# Scooter lift for car in 2026: hitch scooter lifts, carriers and hoists matched to your scooter's weight, hitch, plate rules and price

Source: https://www.mobilitatlas.com/blog/scooter-lift-for-car-guide.html
By Anna, founder of Mobility Atlas (https://www.mobilitatlas.com/about/). Published 13 November 2026.

Hitch scooter lifts, carriers and inside hoists matched to real scooter weights, from Harmar, Bruno and Silver Spring documents, with plate rules, warranties and dated US prices.

## In short

- Choose by the scooter first: its weight with batteries and its wheelbase. Harmar rates the AL015 hitch lift at 150 lb for wheelbases up to 36 inches, the AL160 at 350 lb for 30 to 42 inches, and the AL100 and AL100HD at 350 and 400 lb.
- Pride prints 103.4 lb with batteries for the Go Go Ultra X Gen 3 and 201 lb for the Victory 10 4-Wheel with 40Ah batteries; the Victory is 51 lb over the AL015's limit by our arithmetic.
- Add the lift, the scooter and any swing-away and keep the total under the hitch's tongue weight: a Go Go Ultra X Gen 3 on an AL100 with Harmar's AL105 swing-away comes to 226.4 lb by our sum of printed weights, within the platform's printed length and width.
- A hitch lift can hide the plate: Harmar warns of state plate obstruction laws, Discount Ramps lists 19 states where it says its powered carrier needs a plate riser, and California section 5201(e) has a decal rule for wheelchair lifts and carriers.
- On 13 November 2026 SpinLife listed 16 lifts and carriers with Scooter in their names from $920 to $3,795; the VA schedule sets $3,195 as its maximum for a hitch mount lift.

## The short answer

A scooter lift for a car is chosen by the scooter first and the car second. Write down what your mobility scooter weighs with its batteries, how long it is and where its wheels sit, then find a lift whose printed capacity and platform size clear those numbers, then check that your car, its hitch and your parking space can carry the lift and the scooter together. Four kinds of mobility scooter lift for a car appear in the documents we read: an inside hoist that swings the scooter into the cargo area on a strap, an inside platform that slides it in on a tray, a powered hitch platform that carries it behind the car, and a manual hitch carrier with a ramp that you push the scooter up yourself.

The numbers on the makers' pages show how much room there is. Harmar rates its AL015 hitch lift at 150 lb for scooters with up to a 36 inch wheelbase, its AL160 at 350 lb for wheelbases between 30 and 42 inches, and its AL100 and AL100HD at 350 and 400 lb. Bruno rates the Out-Sider hitch lift at 350 lb and the Curb-Sider hoist at 250, 400 or 450 lb, the last "only when configured by Bruno," its manual says. Pride prints 103.4 lb with batteries for the Go Go Ultra X Gen 3 and 201 lb for the Victory 10 4-Wheel with its optional 40Ah batteries. The Victory would be 51 lb over the AL015's limit, by our arithmetic, and under the AL100's 350 lb, though at 47 inches long it is longer than the AL100's 46 inch extended cradle.

On 13 November 2026 the US seller SpinLife listed 16 lifts and carriers with the word Scooter in their names from $920 to $3,795; a powered hitch carrier sold by Discount Ramps was $1,199.99 and a steel manual carrier $229.99. Whether you can transfer to the car seat safely, and whether you can guide a scooter onto a platform or up a ramp, is a question for your physician, physical therapist or occupational therapist, and whether you can drive is one for a driver rehabilitation specialist. This guide explains the lifts, the paperwork and the questions to ask, then stops.

Mobility Atlas earns a fee or margin when you order through us; the comparison below uses only the makers' published pages, manuals and warranty terms, sellers' dated listings, the VA's pages and one state statute, each read on the date we give. We do not rank the makers.

Mobility Atlas can find and quote a scooter lift or carrier for you, including models and parts that are not listed on our pages. The process: you send an enquiry or a part request, we reply with a written quote that includes delivery to your country, and nothing is charged before you accept it. Our [vehicle adaptations page](https://www.mobilitatlas.com/c/vehicle-adaptations.html) lists a wheelchair-accessible van, hand controls, a docking system, a swivel seat and one car hoist, the BraunAbility Carolift 100, but no hitch scooter lift, so for a hitch lift or carrier send a part request that names your scooter, your car and the lift you have in mind.

This guide goes deeper on scooters than our [car wheelchair lift guide](https://www.mobilitatlas.com/blog/car-wheelchair-lift-guide.html), which covers lifts for every kind of mobility device, the general rule on hitch class and tongue weight, roof boxes, pickups, UK prices and the funding map. We do not repeat those parts here. If you are still choosing the scooter itself, start with our [buying guide for mobility scooters](https://www.mobilitatlas.com/blog/buy-mobility-scooter-guide.html) or the [travel mobility scooter guide](https://www.mobilitatlas.com/blog/travel-mobility-scooter-guide.html); if you need to ride in your chair, the [wheelchair van guide](https://www.mobilitatlas.com/blog/wheelchair-van-guide.html) is the right page.

## How we checked

On 13 November 2026 we read and saved, as text, Harmar's hitch-mounted and hoist lift category pages, its AL100/AL100HD, AL160, AL015, AL001, AL425/AL425HD and AL600 product pages with their specification tabs, its FAQ page, its outside lifts owner's manual (630-00105 B, 18 March 2022), its outside lifts installation and service manual (630-00106 B, 4 April 2022), its inside lifts installation and owner's manual (Rev F, 18 December 2017) and its vehicle lift warranty form (RevC, 16 October 2020). The same day we read Bruno's scooter lift page and its Out-Sider, Curb-Sider and Joey pages, the Out-Sider ASL-275 specification guide and the Curb-Sider VSL-6000G/6900G operator manual of 7 April 2022 (both PDFs hosted by SpinLife), Discount Ramps' pages for two Silver Spring carriers and the SSECC-350 instruction manual, the four pages of SpinLife's vehicle lift list and its AL100 product page, 1800wheelchair's scooter lift page, the VA's Automobile Adaptive Equipment page and schedule, and section 5201 of the California Vehicle Code, as amended effective 1 January 2026.

We also used scooter documents saved earlier for neighboring guides, each with its own read date: Pride's specification pages for the Go Go Elite Traveller 3-Wheel, Go Go Ultra X Gen 3 and Victory 10 4-Wheel (read 9 November 2026) and for the Revo 2.0 4-Wheel, Pursuit 2 and Maxima 4-Wheel (read 12 November 2026); Pride's Scooter Consumer Safety Guide and Golden Technologies' owner's manuals for the Buzzaround Lite and the Patriot (read 13 November 2026); and Medicare.gov's wheelchairs and scooters page (read 9 November 2026).

Our method: we read each page and PDF as text, saved it with the date, and quote only what we saved word for word. Price ranges and weight sums are computed by script from the saved files, with the counting rules stated where they are used. Advice of our own starts with the words In our view, and our reading of a rule or a document starts with In our reading. We tested no lift, placed no order and asked no seller or maker anything.

Limits. Bruno's warranty and brochure links open in a third-party page viewer, which we did not save, so Bruno warranty terms here come from the Curb-Sider operator manual only. SpinLife's product page for the E-Z Carrier 2 did not open its specification section for us; we use only its price line. We did not read a Bruno owner's manual for the Out-Sider or the Joey, and Harmar's hitch lift category has a second page that we did not open.

## Start with the scooter: weight with batteries, length and wheelbase

Every lift in this guide prints a maximum weight. The number to hold it against is the weight of the scooter as it will ride on the lift, which usually means with its batteries, seat and basket. Scooter makers print that figure in different ways, so read the footnotes on the specification page.

| Scooter (maker page, read date) | Weight as printed | Overall length |
| --- | --- | --- |
| Go Go Elite Traveller 3-Wheel (9 Nov) | 95 lb with 12 Ah batteries | 37 in |
| Go Go Ultra X Gen 3 (9 Nov) | 103.4 lb with 12 Ah batteries | 41.5 in |
| Revo 2.0 4-Wheel (12 Nov) | 182 lb with batteries | 47 in |
| Victory 10 4-Wheel (9 Nov) | 185 lb (U1), 201 lb (40Ah) | 47 in |
| Pursuit 2 (12 Nov) | 242.6 lb with standard battery | 57.5 in |
| Maxima 4-Wheel (12 Nov) | 196.8 lb without batteries | 47.5 in |

All six rows are Pride specification pages, and Pride footnotes several of these weights and dimensions as subject to a variance of plus or minus 3 percent. Two details matter for a lift. First, the battery choice moves the weight: the Victory 10 4-Wheel is 16 lb heavier with the optional 40Ah batteries than with U1 batteries, by our subtraction of Pride's two printed totals. Second, some pages print no total with batteries. The Maxima page gives 196.8 lb "Without Batteries" and a battery weight of 36.5 lb each, and its battery line does not print how many; in our view, ask the dealer for the weight on a scale before anyone picks a lift for it.

Golden Technologies prints its weight differently again. The Patriot owner's manual says the scooter "weighs approximately 152 lbs. with the seat, batteries, and tiller basket removed." That is a figure for lifting the frame by hand, not for a lift. A lift carries the seat and batteries too unless you take them off. The same manual's specification table gives "Weight of Unit: (assembled) 302 lbs." and a front-axle-to-rear-axle distance of 40 inches; plan a lift on the 302 lb figure.

### Length is not wheelbase

Harmar rates two of its hitch lifts by wheelbase, the distance between the front and rear axles. Its AL160 page says the lift is optimal for power scooters with a wheelbase between 30 and 42 inches, weighing up to 350 lb, and its AL015 page gives a wheelbase of up to 36 inches. Bruno's Out-Sider guide gives a maximum wheelbase of 38 inches on the standard platform and 46 inches on the large one. None of the Pride specification pages we saved prints a wheelbase; they print a length figure, not a wheelbase. In our reading, a 37 inch scooter can still fit a 36 inch wheelbase limit, and a 41.5 inch scooter may or may not; the overall length does not settle it. In our view, measure axle to axle with a tape, or ask the dealer to, before you rely on a wheelbase rating.

Harmar's wheel cradles depend on tire size too. Its installation manual says, of the AL100, AL160 and AL300 cradles: "Always adjust for tire size." A dealer who sees the scooter on the platform can set the cradle; a number on a page cannot.

## Four ways to carry a scooter, and what each asks of you

The general description of hoists, hybrids and hitch platforms is in our [car wheelchair lift guide](https://www.mobilitatlas.com/blog/car-wheelchair-lift-guide.html). Here is what each kind asks of a scooter rider in particular, in the makers' own words where they print them.

| Kind | Where the scooter rides | What you do | Example and rating |
| --- | --- | --- | --- |
| Inside hoist | Cargo area, on its wheels | Hook docking device, guide by hand | Curb-Sider 250 to 450 lb |
| Inside platform | Cargo area, on a tray | Guide onto tray, strap | Harmar AL600 350 lb |
| Powered hitch platform | Outside, behind the car | Walk scooter on, press switch | Harmar AL100 350 lb |
| Manual hitch carrier | Outside, behind the car | Guide scooter up a ramp, strap | Silver Spring SC500-V3 500 lb |

The ratings are from Bruno's Curb-Sider manual, Harmar's AL600 and AL100 specification tabs, and Discount Ramps' SC500-V3 page.

For a scooter, each choice has a cost the other avoids. A hoist keeps the scooter dry but needs a docking device fitted to the scooter and room in the cargo area. A hitch platform keeps the cargo area free but puts the scooter in the weather and behind the bumper, where it lengthens the car and can cover the plate and the lights. A manual carrier is light and inexpensive but asks you to guide a scooter that, in our table above, weighs 95 to 242.6 lb (the five rows printed with batteries) up a ramp, which in our view is a question to put to your therapist before you buy one.

## Matching scooter to lift: capacity, platform and wheelbase

Which scooter lift for a car fits my scooter? Mobility Atlas read Harmar, Bruno, Discount Ramps' Silver Spring and Pride specification pages on 9, 12 and 13 November 2026, and the fit comes down to three numbers. The first is weight: the scooter as it rides, with batteries and seat, must be under the lift's printed capacity, and Bruno's Curb-Sider manual adds that factors found at dealer installation may reduce the effective rating. The second is wheelbase: Harmar's AL015 takes up to 36 inches and its AL160 30 to 42 inches, and Bruno's Out-Sider 38 inches on the standard platform or 46 on the large one. The third is width: Bruno prints 28.5 inches of usable width on the standard Out-Sider platform. Length counts too: Pride prints 41.5 inches for the Ultra X Gen 3 and Harmar a 40 inch AL015 platform, so weight alone settles nothing. In our view, have the dealer load your scooter before you sign.

| Lift (document) | Capacity | Platform or limit | Lift weight |
| --- | --- | --- | --- |
| Harmar AL015 (page) | 150 lb | 22.5 x 40 in; wheelbase 36 in | 65 or 70 lb |
| Harmar AL160 (page) | 350 lb | 25 x 25 in, cradle to 33 in | 74 lb |
| Harmar AL100 (page) | 350 lb | 26 x 39 in, cradle to 46 in | 83 lb |
| Harmar AL100HD (page) | 400 lb | 26 x 39 in, cradle to 46 in | 84 lb |
| Bruno Out-Sider (spec guide) | 350 lb | 28.5 in wide; wheelbase 38 or 46 in | 89 lb scooter setup |
| Silver Spring SSECC-350 (seller) | 350 lb | 38 x 27.5 in, cradle to 46 in | 96 or 100 lb |
| Harmar AL001, manual carrier (page) | 500 lb | 28 x 48 in, 60 in ramp | 84 lb |
| Silver Spring SC500-V3, manual carrier (seller page) | 500 lb | 47.5 x 27.5 in basket | 83 lb |

Two rows print two weights. Harmar's AL015 page gives 65 lb with the standard three-wheel cradle and 70 lb with the four-wheel cradle option, while the weight table in Harmar's installation manual gives 62 lb for the AL015; the 3 lb gap is small, but in our view plan on the heavier page figure until Harmar confirms it in writing. Discount Ramps' SSECC-350 page says "Weighs 100 lbs." in its key features and "Weight: 96 lbs." in its specification tab; plan on 100 lb until the seller confirms which is right.

### Pairings that pass the printed weight, length and width limits

We kept only scooter and lift pairs that pass the lift's printed capacity, platform or cradle length and width, and, for carriers, the seller's maximum scooter width and basket length. Our script checks each one against the Pride and lift figures.

- Go Go Elite Traveller 3-Wheel on a Harmar AL015: Pride prints 95 lb with batteries, an overall length of 37 inches and a base width of 19.5 inches; the AL015 takes 150 lb on a 22.5 by 40 inch platform, and Harmar says it "can accommodate a three-wheel scooter." Pride prints no wheelbase, so the 36 inch wheelbase limit still has to be measured.
- Go Go Ultra X Gen 3 on a Harmar AL100, or on a Silver Spring SSECC-350: Pride prints 103.4 lb, 41.5 inches long and 19.25 inches wide; the AL100 takes 350 lb on a 26 inch wide platform with a cradle that extends to 46 inches, and the SSECC-350 350 lb on a 27.5 inch wide platform with a cradle to 46 inches. It does not suit the AL015: at 41.5 inches it is longer than that 40 inch platform.
- Victory 10 4-Wheel with 40Ah batteries on a Silver Spring SC500-V3 or a Harmar AL001: Pride prints 201 lb, 47 inches long and a base width of 22.25 inches; the SC500-V3 takes 500 lb, a scooter up to 26.5 inches wide and has a 47.5 inch inner basket, and the AL001 takes 500 lb on a 28 by 48 inch platform. The length margin is half an inch on the SC500-V3 and 1 inch on the AL001, so confirm with the dealer in writing. Pride footnotes the 47 inch length as subject to a variance of plus or minus 3 percent, about 1.4 inches, more than either margin, so have the scooter measured. On the printed numbers it does not suit the AL015 (51 lb over) or the AL100 (47 inches against a 46 inch extended cradle).
- Revo 2.0 4-Wheel on a Silver Spring SC500-V3: Pride prints 182 lb, 47 inches long and a base width of 20.75 inches, inside the carrier's 500 lb, 26.5 inch width and 47.5 inch basket; the half-inch length margin calls for written confirmation from the dealer. Pride's plus or minus 3 percent footnote on that length is larger than the margin. It is 1 inch longer than the SSECC-350's 46 inch cradle.

A counter-example: the Pursuit 2 at 242.6 lb is under the AL100's 350 lb, but at 29.7 inches wide and 57.5 inches long it is wider than the 26 inch platform and longer than the 46 inch extended cradle Harmar prints, so on the printed numbers it does not fit the AL100; in our view, ask Harmar or a dealer which lift they would fit instead.

These pairings use only the printed numbers and are not fit checks. Harmar's FAQ says its Compatibility Calculator "is only meant as a guide and will often return several results," and that its dealers "will be able to discuss the various distinctions and confirm the proper lift for your specific need."

## Powered hitch scooter lifts: Harmar AL015, AL160 and AL100, Bruno Out-Sider

A hitch scooter lift is a platform on a powered post that plugs into the car's trailer hitch receiver. You get off the scooter, guide it onto the platform, and a switch raises it; when the platform is empty, it folds up against the back of the car. Harmar's AL015, AL160 and AL100 pages list a hold-down foot and a rear wheel cradle; Bruno's Out-Sider guide lists a scooter foot assembly.

### Harmar AL015 and AL160: the lighter scooter lifts

Harmar's AL015 is its "Profile Micro Scooter Hitch-Mount Lift." Its page says the lift is "great for scooters" with up to a 36 inch wheelbase weighing up to 150 lb, and "Compatible with most sedans." It is rated for a class I hitch or greater and comes with an AL126 class II adaptor, an automatic hold-down foot and front and rear wheel cradles. The AL160 is rated at 350 lb, weighs 74 lb installed, needs a class I hitch or greater and comes with an AL123 class III adaptor; Harmar's category page calls it "Lightweight" at "just 74 lbs. installed." Its platform is 25 by 25 inches with a cradle that extends to 33 inches.

### Harmar AL100 and AL100HD: the full-size scooter lifts

The AL100 page says "The AL100 and AL100HD are optimal for scooters up to 350 lb or 400 lb (for HD)" and that they are "Compatible with most minivans, SUVs, trucks, and vans." The specification tab lists an 83 lb installed weight for the AL100 and 84 lb for the AL100HD, a 26 by 39 inch platform with a cradle that extends to 46 inches, a class II or greater hitch for the AL100 and class III or greater for the HD. Included are a class III hitch adaptor, the AL107 hitch post and a license plate mount; options are a battery pack, a license plate riser, a swing-away, a scooter cover and the MultiView backup camera.

Harmar's hitch lift table in its installation manual lists the AL100 for class 2, 3 or 5 hitches and the AL100HD for class 3 or 5. SpinLife's AL100 page, read the same day, prints "Class II Hitch," "Class III Hitch" and "Class V Hitch," and a hitch height of 5 to 18 inches. Harmar's current installation manual (Rev B, 2022) gives a normal operating range of 6 to 16 inches from the ground to the bottom of the hitch receiver, and the 2019 Rev A printed 5 to 16 inches; plan on the narrower 6 to 16 until Harmar confirms in writing. The manual says "Any higher vehicles will require a different hitch adapter." In our view, plan on Harmar's narrower range unless the dealer shows you an adapter that covers your car.

### Bruno Out-Sider

Bruno calls the Out-Sider its "most popular exterior platform lift" and says "If you change mobility devices in the future, the Out-Sider can be easily adapted." Its specification guide lists 3- and 4-wheel scooters as a "Yes" and gives a hitch height range of 6 to 24 inches, at least 6 inches from bumper to chassis, and 45 inches from the car to the end of the platform when loading and when traveling. For hitch class it prints classes II and III with 1.25 and 2 inch receivers, and for applications it marks CUV/SUV, minivan, pickup and full-size van as "Yes" and hatchback or sedan as "Limited." The scooter setup weighs 89 lb, and Bruno notes the weights "do not include hitch adapter or securement option weights": 7 lb for the class III adapter and 5 lb for the scooter foot assembly.

### Getting the scooter on and off

Harmar's outside lifts owner's manual tells you to walk the scooter, not ride it: "Walk the mobility device onto the lifts platform. Driving onto the lifts platform may present complications and/or hazards when stepping off of the mobility device." It also says "The mobility device MUST be unoccupied before operating the lift," and "This lift is NOT meant for human transportation."

Two notes for the AL015, AL100, AL100HD, AL100-DE, AL160 and AL300-FULL apply only to scooters. One: "On some scooters, it may be necessary to temporarily move the steering tiller forward to clear the hold-down foot as it lowers into the lock-down position." Two, for scooters with air-filled tires: "Improper inflation will change the deck height of the scooter and therefore change the amount of clamping force the hold-down foot places on the scooter. The scooter can fall off the lift if not properly secured." The installation manual adds that the hold-down foot setting "is critical to the function of the lift and may cause damage to the lift, scooter and/or person if improperly adjusted." In our view, if you change tires or swap to a different scooter, ask the dealer to reset the foot.

## Manual hitch carriers and powered carriers sold online

A manual carrier is a platform or basket on a hitch bar with a ramp. You guide the empty scooter up the ramp, strap it down and fold the ramp. Some carriers sold by online sellers add an electric jack that raises the tray, which puts them between a manual carrier and a dealer-fitted lift.

### Harmar AL001

On the first page of Harmar's hitch lift category, the AL001 is the one described as a "Fully-manual outside carrier." Its AL001 page says "This fully manual hitch-mounted lift is easy to store when not in use," rates it at 500 lb for manual wheelchairs, power wheelchairs and scooters, and prints an 84 lb installed weight, a 28 by 48 inch platform with a 60 inch folding ramp, and a class II or III hitch. Options are a cover and tie-down straps.

### Silver Spring SC500-V3 (sold by Discount Ramps)

Discount Ramps' page for the Silver Spring Steel Deluxe Folding Scooter and Wheelchair Carrier prints a 500 lb capacity, an 83 lb weight, a class III or IV 2 inch hitch, a hitch height of 11 to 18 inches, a basket of 47.5 by 27.5 inches inside, and a three-position bi-fold ramp of 59 1/8 inches. Its usage guidelines say: "Not recommended for use with hitch adapters/extensions. Not designed to carry scooter or wheelchair while occupied." The same block gives a maximum scooter or wheelchair width of 26.5 inches. The page sells straps and a "Cargo Carrier LED Light Kit" as separate accessories.

### Silver Spring SSECC-350, a powered carrier

Discount Ramps' page for the Silver Spring Electric Scooter Lift & Carrier, item SSECC-350, rates it at 350 lb on a 38 by 27.5 inch platform with a cradle that extends to 46 inches, for class II, III or IV hitches and a maximum hitch height of 18 inches. The page adds that carriers are not recommended for hitches less than 12 inches from the ground to the bottom of the hitch without the use of a riser adapter. It says the carrier "raises or lowers in only 20 seconds" and comes with four self-tensioning retractors, a license plate holder, a warning LED light and a manual back-up hand crank. It also says "Wiring harness not included."

The instruction manual linked from that page is stricter in places. It says "Effective loading and unloading of the carrier tray require a paved level surface," "Do not travel unpaved roads with the carrier attached to your vehicle," and "Never ride an occupied scooter onto, or off, the carrier." Its general guidelines say "tie-down straps are sold separately," yet its loading steps describe "the four retractable tie-down straps," as the product page does; check what is in the box. The manual adds that "the jack needs one minute interval before changing directions," which matters if you lower the tray too far and want to raise it again.

## Tongue weight, done with real scooters

Harmar's installation manual, the SSECC-350 manual and both Discount Ramps carrier pages say the load must stay within the hitch's tongue rating, and Harmar's manual adds the swing-away to the sum and tells the installer to keep within the vehicle's Gross Vehicle Weight Rating. Our [car wheelchair lift guide](https://www.mobilitatlas.com/blog/car-wheelchair-lift-guide.html) quotes the rule from Harmar's manual and explains hitch classes. Here we do the sums for scooters from the table above, using only printed weights.

| Pair that passes the printed weight, length and width limits | Our sum |
| --- | --- |
| Elite Traveller 3W 95 + AL015 with 3-wheel cradle 65 | 160 lb |
| Ultra X Gen 3 103.4 + AL100 83 | 186.4 lb |
| Same, plus AL105 swing-away 40 | 226.4 lb |
| Ultra X Gen 3 103.4 + SSECC-350 96 or 100 | 199.4 or 203.4 lb |
| Victory 10 4W 40Ah 201 + SC500-V3 83 | 284 lb |
| Victory 10 4W 40Ah 201 + AL001 84 | 285 lb |
| Revo 2.0 182 + SC500-V3 83 | 265 lb |

The scooter weights are Pride's; the lift weights are Harmar's product pages, Harmar's installation manual for the 40 lb AL105 swing-away and Discount Ramps' pages. Straps, covers, a camera and anything left in the basket add more. At the lifts' own limits the sums are larger: 433 lb for an AL100 with a 350 lb scooter, 583 lb for an SC500-V3 with a 500 lb load and 584 lb for an AL001 with a 500 lb load. In our view, a carrier rated 500 lb does not make a hitch rated for less able to carry it.

What hitch does a scooter lift for a car need? Mobility Atlas read Harmar's installation manual and product pages, Bruno's Out-Sider guide, and Discount Ramps' carrier pages and the SSECC-350 manual in November 2026, and the documents point to three checks. First, the hitch class the lift is made for: Harmar's AL015 and AL160 print class I or greater, the AL100 class II or greater, the AL100HD class III or greater, the Out-Sider classes II and III, and Silver Spring's steel carrier class III or IV. Second, the total: the lift, the scooter with batteries and any swing-away added together, kept under the hitch's recommended tongue weight. Harmar's manual tells the installer to stay within the vehicle's Gross Vehicle Weight Rating, and Discount Ramps' carrier pages say "your hauling weight may be limited by your vehicle's suspension." Third, the hitch height the lift can reach. In our view, ask the installer to write all three figures on the quote.

## Inside hoists for scooters: Harmar AL425 and Bruno Curb-Sider

A hoist lifts the scooter by a docking device fitted to the scooter and swings it into the cargo area.

### Harmar AL425 and AL425HD

Harmar's AL425 page rates the AL425 at 400 lb and the AL425HD at 450 lb, with installed weights of 66 and 70 lb. It says "AL425 compatible with vans, SUVs, and trucks" and "AL425HD compatible with trucks only." Harmar's hoist category page lists 30 inches of headroom as required for this series. The securement line reads "Docking device (not included)"; custom docking devices are an option.

Harmar's inside lifts manual describes what the docking device does: it "is an interface between the lift and the power chair or scooter," and "Most power chairs and scooters can be lifted either by the center seat post or the four-post seat frame." For the trial fit, it tells the installer to "Fold the chair or scooter's seat back (or remove seat)" and measure length, width and height. It also says that "To install the lift, you'll most likely need to drill three holes in the vehicle's floor."

### Bruno Curb-Sider

Bruno's Curb-Sider operator manual says the lift "is designed to lift mobility devices weighing up to 250 lb (113 kg), 400 lb (181 kg), and *450 lb (204 kg)," the last "only when configured by Bruno," and tells owners to "REFER TO THE WEIGHT CAPACITY DECAL LOCATED ON THE LIFT BASE" and "Do not abuse or exceed the maximum lift capacity indicated on the decal." Its load rating table words the top rating as "only when configured and assembled at Bruno." The VSL-6900 version has a telescoping head that extends up to 8 inches for narrow door openings and lifts up to 400 lb. Its section on maximum load rating says: "The lift weight rating is the MAXIMUM load rating." It adds that during dealer installation, factors including "vehicle structure and condition, operating environment, and customer ability may reduce the effective weight rating."

The loading steps are written for a scooter. The manual says to park the scooter alongside the vehicle "as close to the rear of the vehicle as possible," facing the other way, with its front wheel even with the rear bumper, and that "Four (4) feet (1.2 m) of clear space behind the vehicle is usually adequate." Its safety page says "Park the vehicle on a horizontal, level surface. Load and unload on as level a surface as possible" and "Avoid unloading into vehicular traffic." It says "Be sure the power source of the device being lifted (scooter, power chair, wheelchair) is OFF before attaching it to the lift," and "Vehicle engine must be shut off, with transmission set in park (parking brake must be engaged on models with manual transmission)." In its section on loading, it warns of a tip-over risk and says "Keep mobility device at a safe distance from raised surfaces (eg. sidewalk)."

### Rules for the ride

Harmar's inside lifts manual says "ALWAYS check the lifting strap before use and while using the lift. If any wear or damage is noticed DO NOT USE THE LIFT" and "Contact the dealer or installer for repair." It also says "Ensure the chair / scooter is firmly sitting on the floor of the vehicle and not suspended by the lift during transportation." Its operating steps add: "Leave some tension on the strap during transport to eliminate movement of the chair or docking device." Bruno's Curb-Sider manual says to set the scooter's parking brake, to check that the lift belt "remains taut" in the standard loading steps but "remains a little slack" in the VSL-6900 steps, and to store the pendant at least 12 inches off the vehicle floor, because, the manual says, "The pendant is water resistant, but NOT WATERPROOF."

Golden Technologies' Buzzaround Lite and Patriot owner's manuals both say the scooter can be equipped with a docking device "for loading onto a vehicle by means of a mechanical lift or hoist," and tell owners to contact their Golden provider about "docking devices and scooter lift devices." In our view, ask the lift dealer and the scooter dealer together whether the docking device bolts to a part that the scooter maker allows.

## Inside platform lifts: Harmar AL600 and Bruno Joey

An inside platform lift carries the scooter on a tray that swings or slides into the cargo area. Harmar calls these hybrid lifts. Its FAQ says that with a hybrid lift "you must get off your scooter or powerchair and guide it onto the platform, then secure it with either four cam buckles or the hold-down bar."

Harmar's AL600 page says it is "optimal for virtually all powerchairs and scooters up to 350 lbs" and "Compatible with most minivans, SUVs, and vans," and lists a 179 lb installed weight and a 28.5 by 45 inch platform. Options include four self-tensioning Q'Straint retractors and a scooter wheel cradle. That installed weight is more than twice the AL100's 83 lb; in our reading, it rides in the cargo area whether or not the scooter is aboard.

Bruno's Joey page says: "Drive onto the platform, press a button and the Joey safely lifts and stores your mobility device inside the vehicle's cargo area." It rates the Joey at 350 lb and lists a backlit hand-held control, a safety barrier and a self-leveling platform, with a wheel chock, a back-off device and a belt kit as options. Harmar's outside lifts manual, written for its hitch lifts, tells users to walk the device on instead of driving; the two makers word this differently for different products. Harmar's installation manual does have the installer drive the scooter onto the platform once, from the driver's side, to set the hold-down foot. In our view you should follow the manual for the lift you buy and ask the dealer to show you the loading on delivery day.

## Rear view, license plate and lights with a hitch scooter lift

A loaded hitch lift sits behind the bumper, so it can hide the plate, the plate lamp and part of the view from the rear window or camera. Harmar's installation manual puts it plainly: "Understand that some states have strict license plate obstruction laws. Acquaint yourself with local and state laws."

### What the lift documents provide

- Harmar AL100: a license plate mount is included, and a license plate riser and the MultiView backup camera are options. Harmar says the camera, "installed on the lift's platform, is designed with two lenses fixed in two positions to automatically provide a clear view when the platform is stowed or deployed with a mobility device."
- Harmar wiring: the installation manual says "The lift includes a standard two-contact trailer connector. Use this connector for the license plate lamp," and its troubleshooting table says "The license plate light runs from the two-prong trailer plug located on the vehicle harness that powers the lift."
- Bruno Out-Sider: the page lists a back-up camera, a swing-away, a vinyl cover and a third brake light among its options.
- Silver Spring SSECC-350: Discount Ramps' page says warning LED lights sit "on the license plate riser," and the manual's switch panel has a light switch to "illuminate an installed license plate if needed." The page also says the carrier "Includes 7-way RV blade connector plug" and that an adapter may be needed on older vehicles.
- Silver Spring SC500-V3: the page lists no light; a "Cargo Carrier LED Light Kit" is sold as an accessory.

### Which states, by one seller's list

Discount Ramps' SSECC-350 page says "A license plate riser is required to be used with this carrier in the following states" and lists 19: AK, AL, AZ, CA, CO, FL, HI, ID, KS, MT, ND, NV, OR, PA, SD, TX, UT, VA, WA. It adds: "It is your responsibility to understand your state's laws and regulations, as well as any states you will be traveling through." That is a seller's list for one carrier, not a legal survey, and we did not check it state by state.

Can I keep my license plate legal with a hitch scooter lift? Mobility Atlas read Harmar's installation manual, Bruno's Out-Sider page, two Silver Spring carrier pages and one manual, and California Vehicle Code section 5201 on 13 November 2026; the answer depends on your state. Harmar warns installers that some states have strict plate obstruction laws, includes a plate mount with the AL100 and sells a plate riser, and wires a plate lamp from a two-contact trailer connector. Discount Ramps lists 19 states where it says a plate riser is required with its powered carrier. California's code requires the rear plate to be clearly visible and mounted 12 to 60 inches from the ground, but section 5201(e) makes an exception for plates hidden by a wheelchair lift or wheelchair carrier when the owner has a disability plate, or the person using the wheelchair has a placard, and a department decal is shown in the rear window. In our view, ask your licensing office in writing first.

### The California exception, read closely

Section 5201(e) says "it is not a violation of this section if the reading or recognition of a rear license plate is obstructed or impaired by a wheelchair lift or wheelchair carrier and all of the following requirements are met." The owner must hold a special identification plate, or the person using the wheelchair carried on the vehicle must hold a distinguishing placard under section 22511.55, and the operator must display a decal issued by the department "that contains the license plate number assigned to the vehicle transporting the wheelchair." If the decal is displayed, the code says the rules on lighting the plate do not apply, and "This subdivision does not apply to a front license plate." The text speaks of a wheelchair lift or carrier. In our reading, it does not say whether a lift carrying a scooter is included; ask the California DMV before relying on it.

## Hitch height, ground clearance and the daily drive

A hitch lift must reach the ground to load and clear the road when raised. The documents we read print different hitch height ranges, and each applies only to its own product:

| Lift or carrier (document) | Hitch height printed |
| --- | --- |
| Harmar outside lifts (installation manual) | 6 to 16 in (Rev B); 5 to 16 in (Rev A) |
| Harmar AL100 (SpinLife page) | 5 to 18 in |
| Bruno Out-Sider (spec guide) | 6 to 24 in |
| Silver Spring SSECC-350 (seller page) | 12 to 18 in (below 12 in, a riser adapter) |
| Silver Spring SC500-V3 (seller page) | 11 to 18 in |

Harmar's manual pairs the hitch height with an adapter chart that has standard, short, extra long and drop adapters for class 1, 2, 3 and 5 receivers, and it warns: "Only use Harmar-approved hitch adapters with Harmar lifts. Hitch expanders and extenders are strictly prohibited." The SSECC-350 manual says the carrier cannot be used with hitch receivers higher than 18 inches from the ground at the center of the hitch pin hole, measured at a different point from Harmar's, which measures to the bottom of the receiver opening.

### Driving with a scooter on the back

- Driveways: Harmar's owner's manual says "Do not enter steep driveways straight on. Enter and leave at an angle to the street so that the lift does not drag on the ground."
- Rough roads: it says "Always drive slowly over rough terrain such as potholes, unpaved roads, railroad tracks, speed bumps or other uneven surfaces," and "Excessive loads and rough driving will damage your lift and will not be covered by the warranty." The SSECC-350 manual goes further: "Do not travel unpaved roads with the carrier attached to your vehicle."
- Platform position: Harmar says "Do not move the vehicle with the platform down," and "DO NOT leave the lift's platform on the ground."
- Car washes: the owner's manual says "Hand-wash or only use a touch-less automatic car wash with the lift installed," and also "To prevent damage DO NOT use automatic car wash systems." In our view, hand-washing satisfies both lines.
- Swing-away: the owner's manual says "NEVER open the Swing-Away with the mobility device on the lift," "ONLY open the Swing-Away on level ground," and "Safety Pin must be installed before transit to avoid damage and injury."

## Getting the scooter ready to ride

The scooter makers have their own rules for a scooter in or on a car. Pride's Scooter Consumer Safety Guide, in its section on unoccupied motor vehicle transport, says "Do not remain seated in your scooter while traveling in a motor vehicle," and "The scooter user should never sit on the scooter while it is in a moving vehicle."

The same guide says "all removable scooter parts, including the armrests, seat, and shrouds, should be removed and/or properly secured during motor vehicle transport," and "Always be sure your scooter and its batteries are properly secured when it is being transported." It also says "The scooter should be stowed in the trunk of a car or in the back of a truck or van with batteries removed and/or properly secured." In our reading, that line speaks of stowing the scooter inside the vehicle; the pages of Pride's guide we saved do not mention hitch-mounted lifts by name, and its section on lift systems says "We recommend that you closely review the instructions, specifications, and safety information set forth by the manufacturer of the lift/elevation product before using that product." In our view, ask Pride or your provider in writing before you carry a Pride scooter on one. Golden's Buzzaround Lite manual says "Never sit on your Buzzaround Lite when it is being transported," and warns: "If your scooter and its components are not properly and securely stowed during transportation, the scooter or the components may move or become airborne and cause injury or damage."

Golden's manual also has a paragraph on scooters carried on an outside lift, telling owners to remove the seat or secure it with a tie-down system from the lift maker; the text layer of that sentence is garbled in the copy we saved, so we do not quote it. The next sentence is clean: "Failure to do so could result in the seat coming loose and becoming airborne. This situation could cause problems for the traffic behind you and possibly result in an injury." In our view, on a hitch lift either take off the seat and basket, carry them inside the car and secure them there (not loose on the floor), or have the dealer fit the lift maker's approved seat tie-down; do not travel with the seat unsecured.

### A checklist from the documents

1. Turn the scooter off. Bruno's manual says the power source must be OFF before attaching the device to the lift.
2. Check tire pressure on air-filled tires. Harmar ties deck height and clamping force to inflation.
3. Move the tiller forward if the hold-down foot needs room, as Harmar's manual describes for some scooters.
4. Check every strap, cam buckle or retractor. The Silver Spring manual says to "Pull each strap in the opposite direction to confirm it is securely fastened and effective, in order to prevent safety accidents."
5. Raise the lift fully before driving. Harmar says to stop at the top of travel "when you hear the clicking or ratcheting sound," then remove the key.
6. On a Harmar hoist, check the lifting strap first: the manual says if any wear or damage is noticed, "DO NOT USE THE LIFT" and "Contact the dealer or installer for repair."
7. On a hoist, lower the scooter until it rests on the floor, with the strap tension the manual for your lift describes.

## Installation: dealers, trained installers and self-assembly

The dealer-fitted lifts in this guide all point to a trained installer. Harmar's FAQ says: "It is imperative that you use a qualified Harmar dealer since they are professionals who are trained to install and service Harmar products for safe use." Its installation manual says installation requires one person who "has completed training, has obtained certification on installation, is able to instruct the user on the correct operation and has established a safety and maintenance schedule."

Bruno's Curb-Sider manual says: "Bruno products must be installed and maintained by an authorized Bruno dealer, or the warranty will be null and void." Harmar's inside lifts manual says "DO NOT operate this lift until your dealer has satisfactorily instructed you in its proper operation," and "We strongly recommend having a certified dealer install the lift, configure the docking device and instruct the user on correct operation."

Seller-sold carriers are different. The Silver Spring SSECC-350 manual walks the buyer through assembly and says two people are recommended for the step of loading the carrier into the hitch receiver, and its general guidelines say "It is the user's responsibility to read and follow all instructions." SpinLife, which sells Harmar and Bruno lifts online, says it "reviews each and every vehicle lift purchase to make sure the lift will work with your vehicle and mobility product," and asks for the vehicle, hitch height, hitch type and the mobility device.

Harmar's owner's manual also says "Check with a dealer to make sure a new mobility device is compatible with the lift and vehicle before replacing a mobility device." If you plan to change scooters soon, in our view tell the dealer now; Bruno says the Out-Sider "can be easily adapted" when you change devices.

## Power, backup and the car battery

How the lifts draw power from the car, and the Harmar and Bruno manual backups when the car battery dies, are covered in our [car wheelchair lift guide](https://www.mobilitatlas.com/blog/car-wheelchair-lift-guide.html). Two points matter for scooter owners in particular.

For hybrid and electric cars, the current Harmar installation manual (Rev B, 4 April 2022) says its stand-alone battery pack, BAT141386, "can also be used when hybrid or electric vehicles do not have a 12-volt battery capable of supplying power to a mobility lift." An earlier revision (Rev A, 6 December 2019) printed "have" in that line and named the pack AL205. In our view, if you drive a hybrid or an electric car, ask the dealer in writing how the lift will be powered.

For the Silver Spring SSECC-350, sold online, the manual says: "Carry the manual hand crank whenever traveling with the lift in the event your battery has a voltage reduction."

The lift's battery is your car's battery, not your scooter's. For scooter batteries and chargers, see the [mobility scooter repair guide](https://www.mobilitatlas.com/blog/mobility-scooter-repair-guide.html) and the [power wheelchair batteries guide](https://www.mobilitatlas.com/blog/power-wheelchair-batteries-guide.html).

## Warranty, by document

Each warranty below belongs to the one document that prints it. We did not read Bruno's separate warranty page, which opened in a viewer we could not save.

| Document | Term as printed | Labor and transfer |
| --- | --- | --- |
| Harmar outside lifts owner's manual (2022) | 3 years, parts, from retail purchase | Excludes labor; titled transferable |
| Harmar vehicle lift warranty form (2020) | 3 years, parts; installation and retail purchase both printed | Transfer if Calculator approves |
| Bruno Gold warranty (Curb-Sider manual) | 3 years, parts, from installation | Labor first 30 days; original buyer |
| Silver Spring (SSECC-350 manual) | 1 year from accepted delivery | Purchaser pays labor; non-transferable |
| Discount Ramps SC500-V3 page | One Year Warranty | Terms not on the page |

Harmar's warranty form says the warranty "is transferable as long as the application is approved by Harmar's Compatibility Calculator." The form prints two start points: it says the warranty "starts on the date of initial product installation (not to exceed 180 days from the date of manufacture)" and also gives "three (3) years from date of retail purchase"; ask Harmar's dealer which date applies, in writing. Its first sentence requires that the products be "installed, maintained and operated properly by an Authorized Harmar Distributor or Certified Harmar Installer." It also says "Applications involving vehicles or mobility devices not approved by Harmar's Compatibility Calculator will void the warranty." It excludes "labor cost, batteries, paint, rust and covers," and says "Dealers may charge for labor, service, travel, or other associated costs to make repairs, and such charges are not covered by this Limited Warranty." Both Harmar documents ask for the form back within ten days of installation.

Bruno's Gold Limited Warranty in the Curb-Sider manual covers parts for three years after installation and labor by a Bruno dealer "for the first 30 days after installation," and excludes damage from "misuse, abuse, accidents, neglect or modifications NOT made by Bruno Authorized Dealer," consumables and "Reasonable wear and tear." It says "All Service and Warranty issues are handled through the Bruno Authorized Dealer that installed the unit." Bruno's scooter lift pages print "3-Year Limited Warranty" for the Out-Sider, Curb-Sider and Joey.

The Silver Spring manual says its warranties "are NON-TRANSFERABLE and cover only the original end purchaser," that "WARRANTY CLAIMS MUST BE MADE DIRECTLY TO THE ORIGINAL PLACE OF PURCHASE," and that "The purchaser is responsible for labor charges." It also says damage in shipping not noted on the bill of lading at delivery voids the warranty, so in our view inspect the boxes before you sign.

### Maintenance the manuals print

- Harmar outside lifts: the owner's manual says "Oil pivot points on all moving parts every Six (6) months," and grease the vertical tube once a year, or every six months under hard conditions or extreme weather.
- Harmar inside lifts: the manual says "Schedule a preventative maintenance inspection with your dealer at least once a year on motors, lift frame, wiring harnesses, and all moving parts."
- Bruno Curb-Sider: a dealer inspection once a year, or every six months under strenuous use, the manual says.
- Silver Spring SSECC-350: the manual tells owners to check nuts and bolts for tightness from time to time, without an interval.

Harmar's owner's manual is direct about damage: "Stop using the lift immediately if you notice any damage. Do not attempt to transport a mobility device with a compromised lift. [...] Contact your dealer and ask for an evaluation of the lift prior to further use." It also says "Inspect the lift condition often. If ANY parts are worn or damaged, DO NOT USE THE LIFT. Immediately contact the dealer that you purchased the lift from to schedule repairs."

## What a scooter lift for a car costs in the US, November 2026

Bruno and Harmar print no prices; Bruno's scooter lift page says "Costs vary depending on the type of lift, installation and options you may need." The prices below are sellers' figures on 13 November 2026, in US dollars, before tax, as each page printed them. Prices differ by country, dealer, installation, options and funding; what you pay a local dealer can differ from any online figure.

| Item on SpinLife's list | Kind | Tile price |
| --- | --- | --- |
| AL015 Micro Scooter Lift | Hitch, powered | $2,090 |
| AL160 Profile Scooter Lift | Hitch, powered | $2,430 |
| AL100 Universal Platform Scooter Lift | Hitch, powered | $2,305 |
| AL100HD Heavy Duty Platform Scooter Lift | Hitch, powered | $2,805 |
| Bruno Out-Sider Lift | Hitch, powered | $3,128 |
| Universal Outside Carrier (Harmar) | Not printed on tile | $1,155 |
| E-Z Carrier 2 Fold-Up | Hitch, manual | $1,460 |
| AL425 Axis II | Inside hoist | $3,385 |
| AL425HD Axis II | Inside hoist | $4,690 |
| Curb-Sider (Bruno) | Inside hoist | $4,199 |
| AL600 Hybrid | Inside platform | $3,795 |
| Joey Lift (Bruno) | Inside platform | $4,675 |

SpinLife's list printed "51" total items over four pages, and we copied all four. The list tiles print a price and a monthly financing line and no "Starting at" label. The Harmar tile named "Universal Outside Carrier" prints no model number, so we do not tie it to the AL001. SpinLife's AL100 product page printed "Starting at" $2,305.00 with $3,060 next to it; we did not check how that second figure is shown on screen. Its E-Z Carrier 2 page printed "Starting at" $1,460.00.

Our rule for ranges: every tile on the four pages, minus one whose name says it is a patient lift (Hoyer Advance-E Professional Patient Lift). That leaves 50 tiles from $920 to $6,895; the top figure is a tile named "IBIS Wheelchair to Car Access Lift," which we did not open. The 16 tiles whose names contain the word Scooter ran from $920 to $3,795. Bruno's four tiles, including the Out-Sider at $3,128 and the Chariot trailer at $6,519, do not use that word and are outside the second range. These are the ranges of one seller's list on one day, not the market's lowest and highest.

### A second and third seller

1800wheelchair's "Mobility Scooter Lifts & Racks" page printed "8 Result(s)," all on one page. Its tiles name no model numbers; "Harmar's Universal Scooter Lift" was $2,707. The page text shows "Sold-out" just before the Enhance Mobility Hercules Scooter Lift tile at $995; without that tile, the other 7 ran from $1,199 to $3,279.

Discount Ramps' two Silver Spring product pages printed "Pricing shown as of 11/13/2026": the SSECC-350 powered carrier at $1,199.99 with "List Price: $1,299.99," and the SC500-V3 steel carrier at $229.99 with "List Price: $299.99," as each page showed.

A listed price is not an installed price. A hitch if the car has none, an adapter, a swing-away, a plate riser, a camera, a docking device for a hoist, wiring and labor can each add to the total, and the seller pages list several of these as separate choices. In our view, ask for one written quote that lists the lift, every option, the hitch and the labor.

## VA, Medicare and state help

For eligible veterans, the VA's Automobile Adaptive Equipment program is described in our [car wheelchair lift guide](https://www.mobilitatlas.com/blog/car-wheelchair-lift-guide.html). Its schedule, updated 1 October 2026, holds maximum allowable reimbursement amounts that touch scooter owners, among them $3,195 for a "Hitch Mount Lift," $5,190 for an "In-Vehicle Rotary Hoist – Power Wheelchair," $5,084 for an "In-Vehicle Platform Lift," $3,797 for a "Scooter Station," which the schedule lists among securement items and does not describe, and $337 for a "Docking device assembly- Hook N' Go," the schedule says.

Medicare.gov's wheelchairs and scooters page, read 9 November 2026, says Part B "covers wheelchairs and power-operated vehicles (scooters) if you're eligible"; the page as we saved it names no vehicle lift or carrier, and we read no Medicare rule that covers one, so ask your plan in writing. Our [car wheelchair lift guide](https://www.mobilitatlas.com/blog/car-wheelchair-lift-guide.html) sets out the Medicare texts it read. We did not read any state program's rules on vehicle lifts; in our view, ask your state vocational rehabilitation agency and, for veterans, the prosthetic representative before you sign anything.

## Three traps

Trap one: weighing the scooter without its batteries. Pride prints the Victory 10 4-Wheel at 137 lb without batteries and 201 lb with the optional 40Ah batteries, and the Maxima page prints no total with batteries at all. A lift chosen on the lighter figure can be 51 lb short, as the AL015 example shows. In our view, weigh the scooter as it rides, or ask the dealer to.

Trap two: reading overall length as wheelbase. Harmar and Bruno rate their scooter platforms by wheelbase, and the Pride pages we read print overall length only. A scooter that looks short enough on paper may not sit in the cradle, and a scooter that looks too long may fit. Measure axle to axle.

Trap three: forgetting the plate and the rear of the car. A hitch lift can hide the plate, the plate lamp and the rear view; Harmar warns of state plate obstruction laws, one seller lists 19 states where it says its carrier needs a plate riser, and California has its own decal rule for wheelchair lifts and carriers. In our view, settle the plate, the lamp and the camera with the installer before the lift goes on, not after a traffic stop.

## Three composite scenarios

These are composite scenarios, not individual customers. Each one uses only the documents for the scooter and lift named in it, as already quoted in this guide.

Scenario one: a Go Go Elite Traveller 3-Wheel and a sedan. Pride prints 95 lb with 12 Ah batteries, an overall length of 37 inches and a base width of 19.5 inches. Harmar's AL015 page says the lift suits scooters "weighing up to 150 lbs." with up to a 36 inch wheelbase, has a 22.5 by 40 inch platform, can take a three-wheel scooter and is "Compatible with most sedans." With its standard cradle the lift and scooter add up to 160 lb by our sum. The dealer measures the wheelbase, which Pride's page does not print, checks the sedan's hitch label against that total, and fits the AL015 only if both clear.

Scenario two: a Go Go Ultra X Gen 3 and an SUV with a class III hitch. Pride prints 103.4 lb, 41.5 inches long and 19.25 inches wide; Harmar's AL100 is rated at 350 lb, has a 26 inch wide platform with a cradle that extends to 46 inches and weighs 83 lb installed, and the AL105 swing-away adds 40 lb, for 226.4 lb by our sum. The installer compares that total with the hitch's recommended tongue weight and the vehicle's weight ratings, sets the hold-down foot for the scooter's deck, fits the plate mount and wires the plate lamp, and shows the rider the manual override with a 3/8 inch socket.

Scenario three: a Pursuit 2 and a van, with the scooter inside. Bruno's Curb-Sider page names applications for vans, SUVs and trucks. Pride prints 242.6 lb with the standard battery. Bruno's Curb-Sider manual rates the lift at 250, 400 or 450 lb and says the rating is a maximum that a dealer may lower, so the dealer fits a 400 lb configuration and a docking device, explains loading on level ground, away from traffic, as the manual requires, confirms the four feet of clear space behind the van that the manual calls usually adequate, and shows the rider how to park the scooter alongside the van with its front wheel even with the rear bumper and switch it off before hooking it.

## What to ask the dealer or seller

- What does my scooter weigh as it will ride, with batteries, seat and basket, and what is the lift's printed capacity?
- What is my scooter's wheelbase, measured axle to axle, and what does the lift's platform or cradle accept?
- Which hitch class and tongue weight are on my hitch label, and what total did you add up for the lift, scooter and swing-away?
- Which hitch adapter will you use, and will the platform reach the ground and clear the road at my hitch height?
- How will the plate be shown and lit, and is a plate riser needed in my state or any state I drive through?
- Is the hold-down foot or strap setting right for my scooter's deck and tires, and who resets it if I change tires?
- How is the lift powered, where is the manual override, and will you show me how to use it?
- What does the warranty cover, who does the labor, and does the warranty move with me if I change cars or scooters?
- Can you put all of this in one written quote?

If your dealer recommends a specific lift, adapter, docking device or cover and you would like a second quote, send us an enquiry or a part request with the names they used.

## Sources and documents

Each document is listed with its read date in How we checked, near the top, and in the sources list for this guide; the Harmar Rev A installation manual of 6 December 2019 was read on 13 November 2026.

Method in brief: how we checked is set out near the top. Every quote was checked against the saved text by script, every number against the saved files, and every sum and range was computed by script from those files. We do not claim any document says more than the words quoted.

Prices checked November 2026 on SpinLife, 1800wheelchair and Discount Ramps, with the VA schedule of 1 October 2026. Documents checked November 2026: the Harmar, Bruno and Silver Spring manuals and pages, the Pride and Golden scooter documents, the VA pages and California Vehicle Code section 5201, each on the date given above.

If you want us to find a lift, a carrier, an adapter or a docking device that your dealer has named, send an enquiry with your scooter's make, model and weight, your car and hitch, and your town, and ask us to find it or request a quote.

## Common questions

### Can I sit on my scooter while it is on the lift or in the car?

No. Harmar's outside lifts owner's manual says "The mobility device MUST be unoccupied before operating the lift," and Pride's Scooter Consumer Safety Guide says "The scooter user should never sit on the scooter while it is in a moving vehicle." Transfer to the car seat and use its seat belt; how you transfer is a question for your therapist.

### Will a scooter lift fit a sedan?

Some will, by the makers' own words. Harmar says its AL015 is "Compatible with most sedans," and lists the AL001 manual carrier as compatible with sedans, minivans, SUVs and vans. Bruno's Out-Sider guide marks hatchbacks and sedans as "Limited." The hitch, the hitch height and the tongue weight decide it, so ask a dealer to check your car.

### Do I need a dealer to install a scooter lift?

For the Harmar and Bruno lifts in this guide, the documents say yes: Harmar's FAQ calls a qualified dealer "imperative," and Bruno's Curb-Sider manual says its products "must be installed and maintained by an authorized Bruno dealer, or the warranty will be null and void." The Silver Spring carriers sold online come with assembly steps for the buyer.

### How much does a scooter lift for a car cost?

On SpinLife on 13 November 2026, tiles with Scooter in the name ran from $920 to $3,795, and the Bruno Out-Sider was $3,128. Discount Ramps listed a powered Silver Spring carrier at $1,199.99 and a steel manual carrier at $229.99. Prices differ by country, dealer, installation, options and funding, and a hitch, adapter, swing-away and labor can be extra.

### Does the VA or Medicare pay for a scooter lift?

For eligible veterans the VA's AAE program can, after a VHA physician or Certified Drivers Rehabilitation Specialist prescribes it; its schedule of 1 October 2026 sets $3,195 as the maximum allowable reimbursement amount for a hitch mount lift. The Medicare.gov page we read names no vehicle lift, so ask your plan in writing.

### What happens if my car battery dies with the scooter on the lift?

Three of the four powered-lift manuals we read print a manual backup: Harmar's outside lifts use a 3/8 inch socket in the actuator after you unplug the power, Bruno's Curb-Sider has a hand crank the manual says is only for returning the lift into the vehicle, and the Silver Spring manual says to carry its hand crank whenever you travel with the lift. The Harmar inside lifts manual we saved prints none, so ask the dealer.

## Sources

- Harmar: Hitch-mounted lifts: https://www.harmar.com/products/hitch-mounted-lifts/
- Harmar: AL100/AL100HD universal scooter hitch-mount lift (with specifications): https://www.harmar.com/products/al100/
- Harmar: AL160 Profile scooter hitch-mount lift: https://www.harmar.com/products/al160/
- Harmar: AL015 Profile micro scooter hitch-mount lift: https://www.harmar.com/products/al015/
- Harmar: AL001 universal carrier hitch-mount lift: https://www.harmar.com/products/al001/
- Harmar: Hoist lifts: https://www.harmar.com/products/hoist-lifts/
- Harmar: AL425/AL425HD hoist lift: https://www.harmar.com/products/al425/
- Harmar: AL600 Classic hybrid platform lift: https://www.harmar.com/products/al600/
- Harmar: Frequently asked questions: https://www.harmar.com/faqs/
- Harmar: Outside lifts owner's manual, 630-00105 B (PDF): https://cdn.harmar.com/wp-content/uploads/2025/02/09010934/OutsideLifts_Owners-Manual.pdf
- Harmar: Outside lifts installation and service manual, 630-00106 B (PDF): https://cdn.harmar.com/wp-content/uploads/2025/02/09010938/OutsideLifts-Installation-and-Service-Manual.pdf
- Harmar: Outside lifts installation and service manual, 630-00106 Rev A, 6 December 2019 (PDF, hosted by SpinLife): https://www.spinlife.com/files/Outside%20Lift%20Install%20Manual%20(2)14.pdf
- Harmar: Outside lifts installation and service manual, Rev A, page 31 (troubleshooting, hitch height range): https://www.spinlife.com/files/Outside%20Lift%20Install%20Manual%20(2)14.pdf#page=31
- Harmar: Inside lifts installation and owner's manual, TEC0091 Rev F (PDF): https://cdn.harmar.com/wp-content/uploads/2025/02/09010939/InsideLifts_Owners-Manual.pdf
- Harmar: Vehicle lift three year transferable warranty form (PDF): https://cdn.harmar.com/wp-content/uploads/2025/02/09010932/VehicleLifts_Warranty.pdf
- Bruno: Scooter lifts: https://www.bruno.com/scooter-lifts
- Bruno: Out-Sider scooter lift: https://www.bruno.com/scooter-lifts/out-sider-scooter-lift
- Bruno: Curb-Sider scooter lift: https://www.bruno.com/scooter-lifts/curb-sider-scooter-lift
- Bruno: Joey scooter lift: https://www.bruno.com/scooter-lifts/joey-scooter-lift
- Bruno: ASL-275 Out-Sider specification guide (PDF, hosted by SpinLife): https://www.spinlife.com/files/ASL-275%20Spec%20Guide.pdf
- Bruno: Curb-Sider VSL-6000G/6900G operator manual with Gold Limited Warranty (PDF, hosted by SpinLife): https://www.spinlife.com/files/6000G-6900G-O%20VSL-6000G-6900G%20Operator%2004-07-2022.pdf
- Discount Ramps: Silver Spring Electric Scooter Lift & Carrier, SSECC-350 (prices read 13 November 2026): https://www.discountramps.com/mobility/wheelchair-lifts-carriers/p/SSECC-350/
- Silver Spring: SSECC-350 instruction manual (PDF, hosted by Discount Ramps): https://www.discountramps.com/images/art/SSECC-350-DOC__1.pdf
- Discount Ramps: Silver Spring Steel Deluxe Folding Scooter and Wheelchair Carrier, SC500-V3: https://www.discountramps.com/wheelchair-scooter-carrier/p/SC500-V3/
- SpinLife: Vehicle lifts list, pages 1 to 4 (prices read 13 November 2026): https://www.spinlife.com/vehicle-lifts/critpath/match.cfm?categoryID=82
- SpinLife: Harmar AL100 product page with specifications: https://www.spinlife.com/Harmar-AL100-Universal-Platform-Scooter-Lift-Outside-Power-Vehicle-Lift/spec.cfm?productID=71243
- SpinLife: E-Z Carrier 2 product page: https://www.spinlife.com/E-Z-Carrier-E-Z-Carrier-2-Fold-Up-Scooter-and-Power-Wheelchair-Lift-Manual-Scooter-and-Power-Chair-Lifts/spec.cfm?productID=78899
- 1800wheelchair: Mobility scooter lifts and racks (prices read 13 November 2026): https://www.1800wheelchair.com/category/mobility-scooter-lifts/
- Pride Mobility: Go Go Elite Traveller 3-Wheel specifications: https://www.pridemobility.com/go-go-travel-mobility/go-go-elite-traveller-3-wheel/specifications.asp
- Pride Mobility: Go Go Ultra X Gen 3 specifications: https://www.pridemobility.com/go-go-travel-mobility/go-go-ultra-x-gen-3/specifications.asp
- Pride Mobility: Victory 10 4-Wheel specifications: https://www.pridemobility.com/pride-mobility-scooters/victory-10-4-wheel/specifications.asp
- Pride Mobility: Revo 2.0 4-Wheel specifications: https://www.pridemobility.com/pride-mobility-scooters/revo-2.0-4-wheel/specifications.asp
- Pride Mobility: Pursuit 2 specifications: https://www.pridemobility.com/pride-mobility-scooters/pursuit-2/specifications.asp
- Pride Mobility: Maxima 4-Wheel specifications: https://www.pridemobility.com/pride-mobility-scooters/maxima-4-wheel/specifications.asp
- Pride Mobility: Scooter Consumer Safety Guide (PDF): https://www.pridemobility.com/pdf/owners_manuals/safety_guides/sc_consumer_safety_guide.pdf
- Golden Technologies: Buzzaround Lite GB121 owner's manual (PDF, Golden's shared folder): https://www.dropbox.com/scl/fo/dt94cdynjdzbc446t2eku/AO7isLsAdqi2g2-C7NNpdXY/Scooters/GB121%20Buzzaround%20Lite%20Golden%20OM%2001.14.2022.pdf?rlkey=41svp9ejj7y23p4duzln47h61&dl=0
- Golden Technologies: Patriot GR575 owner's manual (PDF, Golden's shared folder): https://www.dropbox.com/scl/fo/dt94cdynjdzbc446t2eku/ADoljdZNMFPaIzgDs60fotk/Scooters/GR575%20Patriot%20Golden%20OM%2002.18.2020.pdf?rlkey=41svp9ejj7y23p4duzln47h61&dl=0
- VA: Automobile Adaptive Equipment (AAE): https://www.prosthetics.va.gov/psas/AAE.asp
- VA: Automobile Adaptive Equipment Schedule, updated 1 October 2026: https://www.prosthetics.va.gov/psas/AAE_Schedule.asp
- VA: Adaptive Equipment Schedule for Automobiles and Other Conveyances (PDF): https://www.prosthetics.va.gov/PROSTHETICS/psas/Documents/VA-Adaptive-Equipment-Schedule-Automobiles-Other-Conveyances_10_01_2026.pdf
- California Vehicle Code section 5201 (display of license plates): https://leginfo.legislature.ca.gov/faces/codes_displaySection.xhtml?lawCode=VEH&sectionNum=5201
- Medicare.gov: Wheelchairs and scooters: https://www.medicare.gov/coverage/wheelchairs-scooters

Read on 13 November 2026. The wording of the article is our own.

## About the author

Mobility Atlas is run by Anna, who has used a wheelchair for 19 years, since she was ten. She started it because she always wanted one place where a person who needs a chair, a wheel, a cushion or a spare part can see everything that is made, side by side, and simply ask for it. She reads and answers every enquiry herself.

Contact: anna@mobilitatlas.com, WhatsApp +66 65 398 9085. Canonical facts about Mobility Atlas: https://www.mobilitatlas.com/about/facts.html
