# Wheelchair footrest replacement in 2026: wheelchair leg rests and elevating leg rests compared, hangers, footplates, fit, prices and warranty

Source: https://www.mobilitatlas.com/blog/wheelchair-footrest-guide.html
By Anna, founder of Mobility Atlas (https://www.mobilitatlas.com/about/). Published 13 November 2026.

Replacing wheelchair footrests and leg rests: swing-away vs elevating, hangers and hinge spacing, footplates, ground clearance as manuals print it, US prices and warranty.

## In short

- A wheelchair footrest replacement is matched by chair model, not by size: Drive lists LK3JELR elevating leg rests for seven named Drive manual chairs (its Blue Streak diagram limits that by serial number), and ShopINVACARE names eight Invacare chairs as examples for T94HCP and says it is not suitable for Drive wheelchairs.
- Swing-away footrests and elevating leg rests are different parts. Whether a person needs elevating leg rests, a different hanger angle or a different footplate height is a decision for their physician or therapist; Medicare's LCD L33792 lists three conditions for covering elevating legrests.
- Footplate clearance differs by manual: no lower than 2-1/2 inches from the ground in the Drive Silver Sport 2, Blue Streak and Viper Plus GT manuals, no closer than 2.5 inches (6.4 cm) in Medline's Guardian guide, at least 5 cm in Karman's KM-5000 manual; in our view, plan on the larger figure.
- On 13 November 2026, SpinLife listed three Invacare elevating legrest lines at $106 to $192 and ShopINVACARE the T94HCP pair at $59.00; part tiles on the first page of a Walmart.com search ran from $9.59 to $86.99 by the first price each tile printed (one tile also listed options up to $94.98), and Disability Lab universal footplates were $34.99 to $54.99 at WheelchairBearings.com (the $54.99 plate shown as sold out).
- Warranty on riggings follows each document (in our reading, riggings count as parts): thirteen months for remaining components in the Invacare Tracer SX5 manual, one year on parts in the Medline Guardian and Ki Rogue 2 documents, three years in the Drive Silver Sport 2 manual, six months on parts in Karman's KM-5000 manual.

## The short answer

A wheelchair footrest replacement covers the parts at the front of a manual or transport chair, which stick out ahead of the chair and, as SpinLife's footrest listing puts it, "can take a beating over time." Makers call these parts front riggings: swing-away footrests, elevating leg rests (legrests in the Invacare and Medline manuals), the hangers that carry them, the footplates your feet rest on, and the calf pads, calf straps and heel loops around them. This guide compares what makers and US sellers list in November 2026: swing-away versus fixed versus elevating legrests, hangers and their angles, receivers and hinge spacing, composite, aluminum and angle-adjustable footplates, one-piece footplates on rigid chairs, how high a footplate must sit above the ground, prices, and warranty.

Which wheelchair footrest replacement will fit my chair? On the pages we read, the one the chair's maker lists for that model, because a footrest hooks onto the frame through a hanger whose hinge pins, spacing and latch can differ by maker. Mobility Atlas read the manuals, order forms and product pages named in this guide, plus the listings of four US sellers. On those pages a replacement is matched by the chair model, not by a size: Drive's elevating leg rest page lists LK3JELR for seven named Drive chairs (see the Blue Streak caveat below); ShopINVACARE names eight Tracer and 9000 chairs as examples for T94HCP and says it is "NOT suitable for use with Drive Wheelchairs." The pages we saved that call a part universal print no hinge spacing, or, for one aftermarket footplate, a bolt hole range of 2 to 6 inches. In our view, order the maker's part for your model and serial number, or get fit confirmed in writing.

Two more questions settle most orders. First, swing-away footrest or elevating leg rest: they are different parts, priced differently, and Medicare treats them differently. Second, which footplate: composite, aluminum, angle-adjustable or, on a rigid chair, a one-piece footplate that bolts across the frame.

The first of those is partly a clinical question. Whether a person needs elevating leg rests, a different hanger angle or a different footplate height belongs to their physician, physical therapist, occupational therapist or seating clinician. Ki Mobility's Rogue 2 manual says: "The footrest height should be [...] determined by working with your clinician to [...] ensure the proper fit for your needs." This guide explains the options, what each maker's document says and what to ask, and then stops.

## How we compared, and our interest

Mobility Atlas earns a fee or margin when you order through us; the comparison below uses the makers' published documents, sellers' listings and public FDA and Medicare records. We did not buy, fit or test any footrest or legrest, and we did not ask any maker or seller a question.

Our method was simple. On 13 November 2026 we opened each page named below in a browser and saved its text, with the address and the date, before writing. For PDF manuals and order forms we extracted the text in the browser and saved the pages that deal with footrests and legrests, marking the gaps. Several documents had been saved a few days earlier and are reused with their own read dates: the Medline Guardian user guide, the Drive Silver Sport 2 and Viper Plus GT manuals, the Karman LT-1000 and KM-5000 documents, the safety and warranty pages of Invacare's Tracer SX5 manual, Medicare's rules and the FDA page on its report database were read on 9 November 2026; Drive's swing-away footrest, elevating leg rest and heel loop pages, the Drive Blue Streak page and manual, and Medline's parts guide were read on 12 November 2026. Where we did arithmetic, such as a price gap or a conversion from centimeters to inches, a script computed it from the saved text.

The makers' documents read on 13 November 2026 were: Invacare's Tracer SX5 user manual (the front rigging, legrest and footplate pages); Ki Mobility's Rogue 2 and Rogue XP manual, its Rogue 2 order form and its Catalyst 5 order form; Permobil's TiLite ZR and ZRA order form dated March 2026; and the ShopINVACARE page for the T94HCP legrests. The sellers were SpinLife (two category listings and two product pages), WheelchairBearings.com (its footplate collection and one product page), Walmart.com (the first page of a search and one product page) and ShopINVACARE. All are US pages and the prices are in US dollars. We also ran openFDA word searches of device reports and recalls and looked up the Medicare codes in the National Library of Medicine's HCPCS table.

Where two documents give different figures for the same thing, such as how high a footplate must sit above the floor, we give both and say which document printed which. Where a page gives no figure, we say so. We tried to read 1800wheelchair.com, but its search page answered with a security check, so we left it out. Prices checked November 2026. Documents checked November 2026.

## Footrests and leg rests at a glance: the core table

Six kinds of front rigging turn up in the documents we read. The table gives one line each, with the document that shows it. Prices are in the price section further down.

| Type | What it does | Where we saw it |
| --- | --- | --- |
| Swing-away footrest | Swings aside and lifts off | Drive, Invacare, Medline, Karman manuals |
| Swing-away elevating leg rest | Also raises the leg, calf pad | Drive, Invacare, Medline, Karman pages |
| Fixed front (folding chair) | Frame and hanger in one, 70 or 80 deg | Ki Catalyst 5 order form |
| One-piece footplate (rigid) | Plate across the front frame | Ki Rogue 2, TiLite ZR forms |
| Flip-up or flip-back footplate | Plate folds out of the way | Ki and TiLite forms, SpinLife |
| Universal aftermarket plate | Bolts onto existing hardware | WheelchairBearings.com |

Two warnings recur in the manuals. Footrests are not steps: Medline's Guardian guide says "DO NOT stand or put pressure on the footrests. When getting in or out of the wheelchair, make sure the footplates are in the up position." And they are not handles: Karman's general user guide, linked from the LT-1000 page, says "Never lift the wheelchair by the swing-away footrests or elevating legrests or armrests. These parts are detachable." In our view, anyone who helps you lift a chair should know both lines before they touch the front riggings.

## Swing-away footrests: how they hang and come off

A swing-away footrest is the front rigging on the folding chairs whose manuals we read from Drive, Invacare, Medline and Karman. In our reading of these manuals, it hangs from hinge pins on the front of the frame, locks facing forward, and swings out to the side when you release a lever, so you can transfer or get closer to a bed or toilet. Then it lifts off. Five manuals print the sequence in similar words.

The Drive Silver Sport 2 manual says: "Release lock by pushing on the front rigging lever. Swing- away foot rest /leg rest out and sideways. Lift to remove." The Drive Viper Plus GT and Blue Streak manuals print the same three steps. The Medline Guardian guide says to fold the footplate up, then "Release the legrest lock by pushing on the legrest lever," and "Swing the legrest outward and to the side." Invacare's Tracer SX5 manual puts the release first: "Push the front rigging release lever inward," then rotate the assembly outward and "Lift the swingaway front rigging assembly off the hinge pins."

Fitting a footrest back on is the same in reverse, and the manuals agree on the shape of it: hinge plates on the footrest drop over hinge pins on the frame, and the footrest locks when you swing it to the front. The Guardian guide says to "Push the legrest rigging to the front until it locks securely into place." The Tracer SX5 manual adds that "it may be necessary to [...] pull release lever toward front of chair to assist the [...] front rigging to lock in place," and that "The footplate will be on the inside of the wheelchair when locked in place." That last line tells you which footrest is left and which is right: the footplate points in.

The Karman KM-5000 manual describes a different mounting: you put the bracket of the swing-away footrest into the front tube of the frame, put the footrest pivot into the end hole, and swing the footrest "to make the release pins fall into the hole of hanger lock base." Karman's general user guide, linked from the LT-1000 page, describes a footrest whose axle pushes into the frame and is held by a bolt. These are three different ways to hold a footrest; in our reading, that is why a footrest from one maker may not fit another maker's chair.

Several footrest listings we read are pairs. Drive's swing-away footrest page names its PH-SF item "Footrests, SentraHD EC XW, 1/pr", SpinLife's T93HEP listing says "Sold as a pair", and ProActive's PP-SF is titled "(Pair)"; but one Walmart.com tile sells a single left side and another prints a price "$20.00/ea". Each side has its own latch, so one side can fail while the other keeps working. In our view, check which part failed before you buy a whole pair: Invacare's Tracer catalogs, as our Invacare parts guide explains, list some legrest parts one by one and mark others as not sold alone.

## Elevating leg rests: what changes and who decides

In the manuals we read, an elevating leg rest is a swing-away footrest with a calf pad and a mechanism that holds the leg at the height you lift it to; Medline's guide names a ratchet rod. The Drive and Medline manuals say to lift it by the footplate until it locks; Invacare's Tracer SX5 manual says the assistant should hold the support tube to raise it. Each manual has a lever to lower it. Drive's Silver Sport 2 manual says to "Lift foot plate on leg rest assembly to desired position. Release leg rest assembly and it will automatically lock into place." Medline's Guardian guide says the legrest "will automatically lock in place due to the ratchet rod." Karman's KM-5000 manual says "You can elevate the footrest directly and stop at any position you desire."

Lowering one is where the manuals print their warnings. Invacare's Tracer SX5 manual says: "Ensure hands and fingers are clear of elevating legrest mechanism before pushing release lever to lower the elevating legrest. Otherwise injury may occur due to pinch points." It adds: "The wheelchair user's leg MUST be supported by an assistant before attempting to lower legrest." The manual's steps then say to support the leg with one hand, push the release lever down with the other, and "Gently, lower user leg down and rest against the legrest."

Elevating leg rests also interact with wheel locks on some chairs. The Tracer SX5 manual says that if the chair has push-to-lock wheel locks, elevating legrests and wheel lock extension handles, "the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side, otherwise injury or damage may result." Medline's guide asks you to "Check to make sure that the legrests do not unlock the wheel locks when they are swung back." Our [wheel lock guide](https://www.mobilitatlas.com/blog/wheelchair-wheel-lock-guide.html) covers the locks themselves.

Should you swap swing-away footrests for elevating leg rests on your wheelchair? Only if your physician or therapist says so, because it is a seating decision, not an upgrade. Mobility Atlas read Medicare's rule for these parts, LCD L33792 in the version in effect in November 2026. It first requires a wheelchair that meets Medicare coverage criteria and a medically necessary accessory; it then covers elevating legrests if the person "has a musculoskeletal condition or the presence of a cast or brace which prevents 90 degree flexion at the knee," or "has significant edema of the lower extremities that requires an elevating legrest," or "meets the criteria for and has a reclining back on the wheelchair." An elevating leg rest also adds a calf pad and a lowering lever someone must work safely. If your therapist agrees, order the maker's elevating leg rest for your model, because, in our reading of the Invacare and Medline manuals, it installs on the same hinge pins.

CMS policy article A52504, which goes with that LCD, separates the two parts in billing: "There is no separate billing/payment if fixed, swingaway, or detachable non-elevating legrests with or without calf pad are provided. Elevating legrests may be billed separately." The Medicare section below says what that means for a replacement.

## Hanger angles: 60, 70, 80 and 90 degrees as the order forms print them

The hanger is the tube that drops from the hinge to the footplate. In our reading, its angle decides how far forward your feet sit: a 90 degree hanger keeps the feet closest under the knees and a 60 or 70 degree hanger puts them further out in front. None of the standard-chair manual pages we saved (Drive, Invacare, Medline, Karman) prints a hanger angle for its swing-away footrest. The angles appear in order forms for configurable chairs.

Ki Mobility's Catalyst 5 order form, effective 8/17/2026, lists four frame types: "Swing Away", "Super Low - Swing Away", "70° Fixed Front" and "80° Fixed Front". Its footrest hanger table has columns for 60°, 70°, 80° and 90° hangers. In our text copy the check marks in that grid are lost, so we only report the angles that the row labels themselves print: 60°, 70° and 80° for extension tube hangers; 70°, 80° and 90° for short and medium front mount hangers; 70° and 80° for long front mount hangers; and 70° and 80° for the fixed front frame. The form also notes that its Extension Tube Hanger and Fixed Front Frame lengths "are based on 70º Hanger / Front Frame Bend." Elevating leg rests on the same form are a separate hanger choice, priced at $307 for "Elevating Leg Rests" and $354 for "Pro Elevating Leg Rests E0990" as options on a new chair.

Rigid chairs have no hanger, so the angle is bent into the frame. Ki's Rogue 2 form lists a "Front Frame Bend" of 90°, 85°, 80°, 75° or 70°, with 90° priced at $157 and the others at no charge. Permobil's TiLite ZR and ZRA form lists a frame angle of 70°, 75°, 80°, 85° or 90°. Both forms tie the angle to other choices: on the Rogue 2, 6 inch casters are not offered with the 85° and 90° bends and a straight footrest taper is required with the 70° bend; on the TiLite ZR, 85° is not offered with 6 inch front wheels and 90° not with 5 or 6 inch front wheels. The reason, in our reading, is space: a steep front frame brings the feet back toward the casters.

For a replacement this matters in two ways. On a folding chair with swing-away hangers, a new hanger at a different angle changes where the feet sit, and Ki's form says its extension tube and fixed front lengths "are based on 70º Hanger / Front Frame Bend". On a rigid chair you cannot change the angle with a part: it is the frame. In our view, keep the angle the chair was prescribed with unless your therapist changes it, and give the seller the angle printed on your order paperwork or chair label if you have it.

## Fixed fronts and one-piece footplates on rigid chairs

On rigid chairs such as the Ki Rogue 2 and the TiLite ZR, the front frame tubes come down to a single footplate, often called a footrest on the order forms, that spans both tubes. The order forms show one footplate across the frame rather than swing-away hangers, though the Rogue 2 manual's transfer steps still say to remove or swing away the footrests. A replacement is therefore a footplate or a footrest assembly for that frame, not a pair of hangers.

The Rogue 2 order form, effective 8/17/2026, lists ten footplate choices. A tubular "open" footplate comes at no charge; priced options run from $32 (tubular footplate with ABS cover) to $283 (high mount angle adjustable flip under), with aluminum angle adjustable at $102, the same with a riser at $172, the hybrid angle adjustable at $94 and an "Angle Adjustable Flip Under (K0040, K0037)" at $236. The TiLite ZR and ZRA form, dated March 2026, makes an angle adjustable footrest standard and lists a "Titanium Footrest w/Flat ABS Cover" at $217, a "Titanium Open Loop Footrest" at $277, an "Angle Adjustable Flip-Back Footrest" at $244 and an "Angle Adjustable High Mount Footrest" at $109. These are option prices on a new chair, not replacement part prices, but they show the range of footplates each frame accepts.

Two numbers on these forms matter for a replacement. The first is footrest width, measured between the front frame tubes: the TiLite form prints a chart from 7.5 to 17.5 inches by rear seat width and taper. A new footplate must fit that space. The second is seat to footrest length, measured from the front of the seat sling to the footplate: the Rogue 2 form offers 8 to 19.5 inches and the TiLite ZR form 13.5 to 19 inches for its standard footrests. SpinLife lists one such part on its own: a TiLite "Flip-Up Footrest Assembly" (model AS100230-Z) at $160, whose overview says it is "Available on TiLite XC, X, SX, YG, and YGS." That list, on the overview we saved, does not name the ZR; ask TiLite or the seller in writing.

Ki's Rogue 2 manual explains how its angle adjustable footplate turns: loosen the two screws that hold it to the clamp, "Once loose, the [...] footplate will easily rotate around the footrest extension tube," pick the angle and retighten "the two M6 screws" to 80 in./lbs; it says "Do not remove the [...] screws from the footplate." For the hybrid angle adjustable footrest it says to loosen two screws under the footrest with a 4mm Allen wrench and "Rotate the footrest to the desired angle." For height on the Rogue 2, it says to loosen a set screw on each side with a 3mm Allen wrench and "Ensure both sides are adjusted equally" before retightening to 40 in./lbs.

## Receivers, hinge pins and hinge spacing

On a folding chair the footrest hangs from a receiver on the frame: hinge pins on the frame and hinge plates on the footrest that drop over them, as the Invacare and Medline manuals describe. The distance between those pins, or between the hinge brackets on the footrest, is the first fitting dimension. Of the seller and maker pages we saved, only one prints it.

Of the pages we read, one prints a spacing. ShopINVACARE's T94HCP page says: "With a 1.5-inch spacing between Swingaway hinge brackets, these elevating legrests are designed to easily integrate with all Invacare wheelchairs." The same page names eight compatible Invacare models and excludes the 9000 Topaz and 9000 Jymni, and says the legrests are "NOT suitable for use with Drive Wheelchairs." SpinLife's tiles for T94HAP and T94HCP say "Made to fit: Any Invacare manual wheelchair"; our [Invacare parts guide](https://www.mobilitatlas.com/blog/invacare-wheelchair-parts-guide.html) goes through that conflict, and in our reading the narrow list is the one to trust.

Drive's swing-away footrest and elevating leg rest pages print no spacing. They list models instead: Drive's elevating leg rest page ties LK3JELR to the "Blue Streak, Silver Sport 1, Silver Sport 2, Silver Sport Reclining, Cruiser III, Cruiser X4, Polyfly", PHELR to the Sentra EC Extra-Wide and STDELR-TF to the "Sentra EC, Sentra HD, Sentra Reclining". Drive's own Blue Streak parts diagram, read 12 November 2026, prints a different footrest for that chair, STDS4S22SF, with the footnote "When stock is gone use STDS4S22SFN", and lists LK3JELR only in its column for serial numbers 4S, 5D, 10H and 21S, with "Not Applicable" in the 5N column. On a Blue Streak, give the seller the serial number and ask Drive or the seller to confirm in writing. Our [Drive parts guide](https://www.mobilitatlas.com/blog/drive-medical-wheelchair-parts-guide.html) has the footrest numbers. The ProActive Medical swing-away footrests on SpinLife (model PP-SF, $65) are described as "compatible with most standard wheelchairs" with no spacing printed on the page we saved. Our own catalog row for a WheelchairParts.Net legrest set (AC-287) records a 3 1/8 in pin spacing; that row and ShopINVACARE's page may measure different points (pins versus hinge brackets), so ask the seller which distance a figure means.

In our view, measure before you order anything sold as universal: the distance between the centers of the two hinge pins on the frame, the outside diameter of the pins, and the distance from the top pin to the frame tube above it. Then send those numbers with a photo and the chair's model and serial number. A seller who knows the part can match it or say no.

## Footplates: composite, aluminum, angle-adjustable and universal

The footplate is the flat part your foot rests on. On folding chairs each footrest has its own footplate that flips up; on rigid chairs one footplate spans the frame. The documents we read name four kinds.

- Composite (plastic) footplates. Drive's Silver Sport 2 page says its footrests include plastic foot plates with heel loops; Drive's swing-away footrest page lists a "Plastic Footplate"; the Catalyst 5 order form lists a composite footplate at no charge.
- Aluminum footplates. Medline's parts guide page lists a "Footplate Assembly, Aluminum" (WCA806900, sold as a pair) for its basic steel transport chair MDS808200; SpinLife's T94HAP legrests come with aluminum footplates.
- Angle-adjustable footplates, which tilt to set the ankle angle. The Rogue 2, Catalyst 5 and TiLite ZR order forms all list them, several with the code K0040.
- Universal aftermarket footplates, sold to replace the plate alone and keep the existing hardware, such as the Disability Lab plates on WheelchairBearings.com.

Folding chairs need the footplates up before they fold. The Tracer SX5 manual's folding steps say: "Pivot footplates upward to vertical position." Drive's Silver Sport 2 manual starts its folding step with "First fold foot plates to vertical", and Karman's KM-5000 manual says to flip up the calf pad and then "Flip up the footplate." A cracked hinge on a footplate is therefore not only a comfort problem: in our view a plate that will not stay up gets in the way of every transfer and every fold.

Invacare prints how its footplates are held at height. The Tracer SX5 manual describes two systems. In the spring button version, "The elevating legrest has two sets of release [...] buttons, one set above the other," and you push the buttons in and slide the footplate assembly to a new hole, then "Ensure that the release buttons fully protrude from holes on both [...] sides of the front rigging support." In the bolt-in-place version, a threaded rivet goes through from the outside and a button head screw from the inside, tightened to "32 in-lbs". So two Tracer SX5 chairs can have different footplate tubes, and a replacement tube should match the system on your chair.

Universal footplates take a different approach. The Disability Lab footplate page on WheelchairBearings.com sells plates by type and size: "Flip-Up" plates that bolt at the back and "Fixed" plates that bolt at the front. The 10 by 7 inch plate we saved is 3/16 inch aluminum 5052 and lists a minimum bolt hole spacing of 2 inches and a maximum of 6 inches. The page tells you to check three things: whether your plate bolts at the back or front, how wide the space between your two downward tubes is, and the distance between your two bolts: "Measure the space between your two bolts on your current footplate." It also warns: "Do not install these footplates on power wheelchairs or wheelchairs that use an individual footrest for each foot." In our reading, these plates are for chairs with one footplate across the front, not for swing-away footrests.

Ki's Rogue 2 manual, in its general warnings about Ki Mobility's footrest options, warns that using a footrest without supportive foot coverings like shoes can result in serious injury to your feet; it says the footplates may be smaller than your feet, will not protect them from bumps against walls or doors, and are intended to be used with supportive foot coverings like shoes; it says a footpad or footbox can be added if you do not wear them. The same warning says that anyone with skin breakdown or other tissue integrity issues should discontinue use and seek advice from a clinical professional trained in skin care, such as a doctor, nurse or therapist.

## Calf pads, calf straps, heel loops and toe loops

Small soft parts keep feet and legs on the riggings. On the pages we read they are also sold on their own and carry their own Medicare codes, which the National Library of Medicine's HCPCS table describes as: E0951 "Heel loop/holder, any type, with or without ankle strap, each"; E0952 "Toe loop/holder, any type, each"; E0995 "Wheelchair accessory, calf rest/pad, replacement only, each"; K0038 "Leg strap, each"; and K0039 "Leg strap, h style, each". A code printed on a maker's page is the maker's coding, not a promise that any payer will cover it.

Heel loops sit at the back of each footplate. Drive sells them as STDS831, named "Heel Loops, 1pr" on its page, with E0951 in its product options tab; the page prints no price for visitors who are not signed in. Ki's Catalyst 5 order form lists "Heel Loops (E0951)" at $44 and "Adjustable Heel Loops (E0951)" at $54 as options on a new chair, and says heel loops are not available with its one piece flip up angle adjustable footplate. SpinLife's T93HEP footrests are listed as "W/O Heel Loops", so in our reading heel loops would be a separate order with that pair.

Calf straps appear on both order forms for configurable chairs. The TiLite ZR and ZRA form sizes them by footrest width: its Velcro adjustable strap (ZCLF2, $44) comes in small for 9 to 12 inch, medium for 11 to 15 inch, large for 14 to 17 inch and extra large for 16 to 19 inch footrest widths. The Bodypoint padded version (ZCLF3) is $109 and a buckle strap (ZCLF1) $34. Ki's Catalyst 5 form lists three calf straps at $43, $75 and $139. On a replacement, in our view, the footrest width is the number to send.

Calf pads belong to elevating leg rests. Medline's parts guide lists an elevating legrest assembly with calf pads (WCAA0020, one pair) on its Guardian K1 page. ShopINVACARE lists T94HCP with padded calf pads, and SpinLife lists T94HEP with "(Non-Padded Calf Pads)" in its title. Karman's KM-5000 manual says its calf pad "can be adjusted upward and downward, forward and backward, rightward and leftward to suit the user's calf."

Ki's Rogue 2 manual explains why these small parts exist. Ki Mobility recommends heel loops and calf straps and says that, used properly, they help keep the legs and feet from slipping off the footplate, which could let the feet become entangled in the chair or strike the ground; it calls riding without properly fitted heel loops and calf straps a potentially hazardous situation. Which strap, loop or positioner a person needs, and how tight, is a seating question for their therapist.

## How high the footplate must sit: ground clearance as the manuals print it

How low can a wheelchair footrest sit above the floor? No lower than the figure in your own chair's manual, and the manuals disagree. Mobility Atlas read the footrest pages of seven manuals, Karman's user guide and three order forms. Drive's Silver Sport 2, Blue Streak and Viper Plus GT manuals each say the "Footrest should not be lower than" 2-1/2 inches "from the ground to ensure clearance." Medline's Guardian guide says "DO NOT adjust the footrests any closer than" 2.5 inches (6.4 cm) "from the floor." Karman's KM-5000 manual says: "The footrest height must be at least 5cm above the ground." That is about 1.97 inches, about 0.53 inch less than the Drive and Medline figure. In our view, plan on the larger clearance unless your chair's maker confirms its own figure in writing. The Tracer SX5 and Rogue 2 manual pages we saved print no footplate clearance. A longer replacement footrest can break the rule the day it is fitted, so measure after fitting.

In our reading, the floor clearance is there because a footplate that is too low can catch on thresholds, curb cuts and ramp edges and stop the chair. Ki's manual, in its section on riding, warns about "surface transitions" that could cause the front casters or footplate to catch, causing the wheelchair to abruptly stop, which it says could cause it to tip unexpectedly resulting in a fall or loss of control. The same manuals also set a limit in the other direction, at the seat. Drive's Silver Sport 2 manual says "Front rigging should not be so low that it causes uncomfortable pressure to thighs at front of seat upholstery." Medline's guide says the front rigging "should not be lowered to the point that it causes pressure on the thighs at the front of the seat upholstery." Karman's KM-5000 manual says to make sure "the user's thigh is safe on the seat upholstery, and inner knee does not interfere with the front edge of seat upholstery."

The order forms for configurable chairs turn this into a measurement rule for new chairs. Ki's Rogue 2 form says seat to footrest length "Should be at least" 2.5 inches "shorter than Front Seat Height", and its Catalyst 5 form recommends a footrest length of at least 2.5 inches shorter than front seat height. Permobil's TiLite ZR and ZRA form says the seat to footrest measurement "must be at least" 2 inches "shorter than Front Seat Height". Worked through by our script for a chair with a 19 inch front seat height, Ki's recommendation allows a seat to footrest length up to 16.5 inches and TiLite's rule up to 17 inches. The cushion on the seat changes where the thighs actually sit, so in our view these numbers are a check on a replacement, not a way to choose your length.

Who sets the height? Drive's manual says that when adjusting length, the "user should be sitting in wheelchair with feet on the foot plates." Ki's says the height "should be [...] determined by working with your clinician to [...] ensure the proper fit for your needs." Karman's KM-5000 manual says the footplate height should be adjusted "according to the user's calf length to reduce pressure on the body." In our view the person who prescribed the chair should set or check the length after any replacement.

## Setting footrest length: the steps as the manuals print them

In the manuals we read, footrest length is set by sliding a tube or axle and locking it. The locking method differs, and a replacement may use a different one from the part it replaces. Here is what each manual prints.

- Drive Silver Sport 2 and Viper Plus GT manuals say: "Loosen bolt on the clamp around support assembly. Raise or lower foot plate to desired position that will provide maximum support of thighs." The person sits in the chair with feet on the footplates while this is done. Drive's current Silver Sport 2 page says its riggings have "tool-free adjustable length riggings", while the 2014 manual describes a bolt clamp; ask Drive or the seller which system your chair has before ordering a replacement.
- Medline Guardian guide says: "Loosen the plunger by pulling out", adjust the length "by pushing the push button", then "Let go of the push button and engage the plunger by pushing down."
- Invacare Tracer SX5 manual, spring button version: remove the front rigging, lay it on a flat surface, pull the cam lock lever up, push in the release buttons, move the footplate assembly, check the buttons protrude on both sides, then "Rotate cam lock lever down to locked position."
- Invacare Tracer SX5 manual, bolt-in-place version: remove the front rigging and lay it on a flat surface, pull the cam lock lever up, remove the threaded rivet and button head screw, line up the holes, insert the rivet from the outside and the screw from the inside, tighten to 32 in-lbs, then "Rotate cam lock lever down to locked position."
- Karman KM-5000 manual: loosen the bolt at the side of the footrest tube with the tool provided, choose the height, tighten the screw, "Then tighten the nut as a locknut from outside."
- Karman's general user guide, linked from the LT-1000 page: it says to push the axle into the frame "until a desirable length and then tighten the bolt to secure the footrest."
- Ki Rogue 2 manual (rigid chair): loosen the set screw on each side with a 3mm Allen wrench without removing the screws, move the footrest tube, adjust both sides equally and retighten to 40 in./lbs.

Two points follow, in our view. First, keep the old footrest until the new one is set to the same length, and measure the old one from the footplate to the hinge before it goes. Second, a manual's torque figure, where one is printed (32 in-lbs on the Tracer SX5 bolt, 40 in./lbs and 80 in./lbs on the Rogue 2), needs a torque wrench; if you do not have one, a supplier or technician should do it. Medline's guide says: "A qualified wheelchair technician must perform any repair or change to this wheelchair or serious injury may occur."

## Transfers, folding and transport: what the manuals say about front riggings

The transfer steps in the manuals move or remove the front riggings, so the transfer pages are footrest pages too. Invacare's Tracer SX5 manual, in its section on transferring, says: "Remove or flip up the armrest. Engage wheel locks. Swing away or remove front rigging." Medline's Guardian guide says: "Remove the armrest and the footrests that are in the transfer path." Ki's Rogue 2 manual lists, before transferring: engage the wheel locks, rotate the casters forward, and "Remove or swing away the footrests."

The Drive, Karman, Medline and Invacare manuals we read warn against standing on the footrests. Drive's Silver Sport 2 manual says: "When getting in or out of wheelchair, do not stand on or apply weight to foot rests." Karman's KM-5000 manual says: "Never stand on the footplates when getting in or out of the chair." Karman's general user guide, linked from the LT-1000 page, says: "Never stand on the footrests, for the chair may tip forward." Medline's warning is quoted in the table section above. Invacare's Tracer SX5 manual, in its general warnings, says: "DO NOT use the footplate as a platform. When getting in or out of the wheelchair, make sure that the footplates are in the upward position."

Medline's guide, in its passage on taking an occupied chair up or down stairs, where it says "Two assistants with adequate body strength and endurance must be present", says "DO NOT lift the chair by any removable parts (i.e. swing-away footrests)." Karman's general user guide, in its folding section, warns against lifting the wheelchair by the swing-away footrests or elevating legrests. For storing and carrying, the Rogue 2 manual points readers to the sections on removing options and accessories "to decrease size for [...] stowing", and Invacare's Tracer SX5 specifications give the chair's weight "without front riggings". In our view, when footrests come off for a car trip, put them where they cannot slide or fly about in the vehicle, and check both latches click home when you refit them.

## Part numbers by chair, as the makers print them

Maker part numbers for front riggings are model specific. We list the numbers we found on the pages we read; for Drive and Invacare chairs, our neighboring guides go through the parts catalogs and diagrams line by line, so we do not repeat them here.

- Drive: the swing-away footrest page lists STDS3J24SF, STDSF-TF, PH-SF and RTLREB-12 by model, with the Blue Streak under STDS3J24SF; for the Blue Streak, see the diagram caveat in the hinge spacing section above. Our Drive parts guide covers the diagrams.
- Invacare: our Invacare parts guide shows that Invacare's Tracer and 9000 catalogs list the T93H series as the swing-away footrest and the T94H series as the elevating legrest, split by build date. ShopINVACARE sells T94HCP; SpinLife lists T94HAP, T94HCP, T94HEP and T93HEP. Our Invacare parts guide covers the catalog tables.
- Medline Guardian K1: Medline's parts guide page headed "Guardian K1" lists WCAA0015, "Footrest Assembly, Swing Sway" (one pair), and WCAA0020, the elevating legrest assembly with calf pads (one pair).
- Medline basic steel transport chair MDS808200: the same guide's page lists WCA806965HEMI, "Footrest Assembly with Aluminum Footplate" (one pair), WCA806900, the aluminum footplate assembly (one pair), and WCA806910, "Footrest Mounting Pin" (4 each).
- TiLite: SpinLife lists the Flip-Up Footrest Assembly AS100230-Z for the TiLite XC, X, SX, YG and YGS.

A caution on the Medline numbers: in our text copy of the guide the order dots do not line up with the model columns, so we tie each number only to the page heading and the row it sits on. If your chair is not the model on that page heading, ask Medline or the seller to confirm in writing. The same applies to every number in this list: a part number fits the models its page names, and we did not infer fit for any model a page does not name.

The serial number label is the other half of the answer. Invacare's catalogs split front riggings by date, as our Invacare guide shows, and the Tracer SX5 manual describes two footplate height systems. Send the model and serial number with any order, and a photo of the hinge and the footplate.

## What footrests and leg rests cost at US sellers

These are the prices printed on the pages we saved on 13 November 2026, all in US dollars at US sellers. Prices differ by country, seller and sales period, and funding changes what you pay; a page's price is an offer on that day, not a promise.

| Seller and item | Model or item no. | Price as printed |
| --- | --- | --- |
| SpinLife: Invacare hemi elevating legrests, aluminum footplates, padded calf pads | T94HAP | $191 |
| SpinLife: Invacare hemi elevating legrests, composite footplates, padded calf pads | T94HCP | $192 (also shown struck through) |
| ShopINVACARE: the same legrests, 1 pair | T94HCP | Regular price $59.00 USD |
| SpinLife: Invacare elevating legrests, non-padded calf pads (pair) | T94HEP | $106, $117 struck through |
| SpinLife: Invacare swingaway composite footrests without heel loops (pair) | T93HEP | $69 |
| SpinLife: ProActive swing away foot rests (pair) | PP-SF | $65 |
| SpinLife: TiLite flip-up footrest assembly | AS100230-Z | $160 |
| SpinLife: ProActive Protekt footrest extender / legrest pad | 4700X | Starting at $50 |
| SpinLife: Ki Mobility Dynaform ankle positioner (pair) | DYNAAP | $182, $202 struck through |
| WheelchairBearings.com: Disability Lab universal footplates, 5 tiles | no item no. on tiles | $34.99 to $54.99 |
| Walmart.com: Drive elevating legrest, 1 pair | LK3JELR | $51.08 |

The two T94HCP lines differ by $133 by our arithmetic, and the pages do not say why; our [Invacare parts guide](https://www.mobilitatlas.com/blog/invacare-wheelchair-parts-guide.html) covers Invacare prices across sellers. In our view, ask each seller for a written total with delivery.

SpinLife's two footrest listings held 6 and 2 items. Its Elevating Leg Rests listing included the ProActive PP-SF set, whose own title and page call it swing away foot rests, not elevating leg rests; the page says the Protekt footrests are "compatible with most standard wheelchairs" and prints no hinge spacing. The TiLite and ProActive product pages each show the words "No Warranty" in a box headed "THE SPINLIFE DIFFERENCE INCLUDES:". We did not read SpinLife's warranty terms for these items, so in our view ask SpinLife in writing what warranty applies before buying.

WheelchairBearings.com's footplate collection held 5 tiles, all Disability Lab universal footplates, from $34.99 for 7 by 6 inch front bolt fixed plates to $54.99 for a 12 by 7 inch rear bolt flip up plate shown as sold out; the filter counted 4 in stock and 1 out of stock. The tiles print no item numbers.

Walmart.com's search for wheelchair elevating leg rests printed 133 results; we read the first page as it loaded. It carried 46 distinct tiles with a price line. We counted a tile as a part when it sells a leg rest, footrest, footplate or pad on its own; 33 tiles offered a whole wheelchair or transport chair (titles giving a seat size, arms, recline or a weight capacity) and are left out. The 13 part tiles ran from $9.59 to $86.99 by the first price each printed; the "Elevating Wheelchair Leg Rest" tile also printed options up to $94.98. Search tiles do not name the seller; Walmart.com includes marketplace sellers.

| Walmart.com tile (title as printed, shortened) | Price on tile |
| --- | --- |
| Universal Wheelchair Elevating Legrests | $69.00 |
| drive Elevating Legrest For drive Power Wheelchair LK3JELR | $51.08 |
| Elevating Wheelchair Leg Rest - Elevated Foot Rest | $59.99 (options from $59.99 to $94.98) |
| Invacare Wheelchair Elevating Legrests - Padded Calf Support | $49.99 |
| Wheelchair Footrest Leg Rest Elevating Pads | $44.80 |
| Sugagale Wheelchair Elevating Legrests | $52.00 |
| Wheelchair footrest pad,Elevating Leg Rest,Swing-Away Footrests | $49.99 |
| 2Pcs Wheelchair Elevating Legrests | $9.59 + $1.95 shipping |
| 2 Pack Wheelchair Leg Rest Footrest, Hammock | $19.98 |
| Elevating Legrest, 1 Pair | $59.99 |
| Healthline Wheelchair Foot Rest Swing Away Legrest | $39.99 ($20.00/ea) |
| Dynarex Heavy Duty Plus Wheelchair Elevated Leg Rests | $86.99 |
| Invacare Wheelchair Legrest with Heel Loops | $39.24 |

Read those tiles with care. The cheapest, "2Pcs Wheelchair Elevating Legrests", is $9.59 plus $1.95 shipping, $11.54 in all by our arithmetic, for a title that names no maker, model or fit. The Healthline tile prints $39.99 and "$20.00/ea". The Drive tile says "For drive Power Wheelchair", while Drive's own page lists LK3JELR for manual chairs (see the Blue Streak caveat in the hinge spacing section): the Blue Streak, Silver Sport 1, Silver Sport 2, Silver Sport Reclining, Cruiser III, Cruiser X4 and Polyfly. Its product page says "Sold and shipped by Simply Medical" and lists one more seller "Starting from $57.45". In our view, trust the maker's model list over a marketplace title.

Drive's own pages for its footrests, leg rests and heel loops print "SIGN IN TO VIEW PRICE", so we have no maker price for them. Mobility Atlas can find and quote footrests, elevating leg rests, footplates, calf pads, heel loops and hinge hardware, including parts that are not listed. Send an enquiry or part request through the [wheelchair parts and accessories page](https://www.mobilitatlas.com/c/wheelchair-parts-accessories.html) with the chair's make, model and serial number, which side, and photos of the hinge and footplate; you receive a written quote with delivery to your country, and nothing is charged before you accept it.

## Leg rest and footplate options on a new chair: the order forms

If a replacement is not the only route, because the chair is due for renewal, the order forms show what a configurable chair can carry from the factory. Ki's Catalyst 5 form, effective 8/17/2026, is the clearest on elevating leg rests. Its standard ELR comes with an extension tube in three ranges: short 11.75 to 16.75 inches, medium 13.75 to 18.75 inches and long 16.25 to 21.25 inches. Its Pro ELR has a low pivot setting (short 12 to 18 inches, long 14.5 to 21.5 inches) and a high pivot setting (short 10.5 to 16 inches, long 13 to 19.5 inches). On that form the Pro ELR costs $47 more than the standard ELR as a new-chair option, and both are marked as available only with the classic hanger release.

The same form prices footplates for the folding Catalyst 5 from $208 (composite angle adjustable, or the one piece flip up angle adjustable with a 3 inch extension) to $337 (the aluminum locking multi-angle adjustable footplate, available only with front mount hangers), with a plain composite footplate at no charge. It lists an ELR foam knee pad pair at $386 and a Pro ELR gel pad cover pair at $468. On the rigid Rogue 2 and TiLite ZR, the footplate choices and prices are in the rigid chair section above.

These are list prices for options on a new chair as each form prints them, and each form adds a note on codes. The TiLite form says "HCPCS Codes are for reference purposes only." Ki's forms say "Proper use of HCPCS Codes does not ensure coverage or payment." The TiLite form says the chairs "must be fitted by a qualified healthcare professional." In our view that applies to a changed rigging on an existing chair too.

## Warranty and returns: document by document

Where a document splits frame from parts, front riggings fall on the parts side in our reading, so the shorter term applies. Each line below belongs only to the document that prints it.

- Invacare Tracer SX5 user manual: side frames and cross members five years; "upholstered materials (seat, back and armrests of the arm assembly) and remaining components" thirteen months, with a copy of the seller's invoice. It says the warranty "does not include any labor or shipping charges incurred in replacement part installation or repair" and is "not transferable or assignable to any subsequent purchaser or owner." Its wear-and-tear table, which it calls "just a general guideline", lists "Footplate Covers" and "Calf Pad (if applicable) Foam and Cover", and the warranty "shall not apply to normal wear and tear".
- Medline Guardian user guide: frame for the life of the chair; the guide says "Medline also warranties the parts and upholstery on the wheelchair to be free from defect in materials and workmanship for a period of one (1) year from date of purchase by the original purchaser." It excludes "normal wear and tear".
- Drive Silver Sport 2 manual: three years from purchase for the original consumer purchaser; "The warranty does not extend to non- durable components, such as rubber accessories, casters, and grips".
- Drive Viper Plus GT manual: a lifetime limited warranty for the original consumer purchaser, with the same exclusion for non-durable components.
- Ki Mobility Rogue 2 and Rogue XP manual: frame and quick-release axles for the life of the original purchaser; "All other Ki Mobility-made parts and components of this wheelchair are warranted against defects in materials and workmanship for one year from the date of first consumer purchase." It applies "in North America only".
- Karman KM-5000 manual (MVP-502 series): it prints two lines that disagree on the frame, "for the lifetime from the date of purchase, 6 months on parts" and "for one year from the date of purchase, 6 months on parts." Both say six months on parts, and it says "Warranty applies in the U.S. only." It says "Warranty is NOT TRANSFERABLE" and that goods need an R.M.A. number before they are returned.
- Karman's general user guide, linked from the LT-1000 page: its warranty names other Karman models (KN-700 to T-2700) with "6 months on parts"; the LT-1000 is not in that list, so ask Karman which terms apply. The guide says labor and freight charges are not included in the warranty, and "Warranty applies in the U.S. only."

Two practical points follow. The Invacare, Drive and Karman documents send warranty questions to a dealer: Invacare's says "please contact the dealer from whom you purchased your Invacare product." In our reading, a replacement bought from another seller carries that seller's terms, not the chair's. Walmart's LK3JELR page printed "Free Holiday returns until Jan 31". Medline's guide says modifications such as using "non-authorized / non-approved parts" may increase the risk of serious injury to the user and "void the warranty"; in our view, a universal part fitted to a chair still under warranty is worth a question to the maker first.

## Medicare, codes and funding

Medicare in the US uses separate codes for front rigging parts. The National Library of Medicine's HCPCS table lists, among others: K0052 "Swingaway, detachable footrests, replacement only, each"; K0053 "Elevating footrests, articulating (telescoping), each"; E0990 "Wheelchair accessory, elevating leg rest, complete assembly, each"; K0195 "Elevating leg rests, pair (for use with capped rental wheelchair base)"; K0043 and K0044 for a footrest lower extension tube and upper hanger bracket; K0046 and K0047 for the same on an elevating legrest; K0051 for a cam release assembly; K0040, K0041 and K0042 for adjustable angle, large and standard footplates; and E0951, E0995 and K0038 for heel loops, calf pads and leg straps.

CMS policy article A52504 (version 61, read 9 November 2026) explains two of these: "Elevating legrests that are used with a wheelchair that is purchased or owned by the beneficiary are coded E0990. This code is per legrest. Elevating legrests that are used with a capped rental wheelchair base are coded K0195. This code is per pair of legrests." It also says that for transport chairs, "Accessories provided with the initial issue of a transport chair are not separately billable with the exception of elevating legrests (E0990, K0195)," and that a replacement accessory for a transport chair is billed with E1399. LCD L33792, version 43 (effective for services on or after 10/01/2025, ending 12/19/2026), sets the coverage criteria for elevating legrests quoted in the elevating leg rest section above; the future version, effective 12/20/2026, prints the same three criteria in the copy we saved.

Medicare's booklet on medical equipment treats owned and rented equipment differently. For owned equipment it says "the supplier who sold it to you isn't required to repair it" and "If you own Medicare-covered DME and other devices, Medicare may also cover repairs and replacement parts." For rented equipment it says "If you rent equipment, your supplier must maintain and repair the equipment and keep it in good working order at all times," and "Any costs for repairs or replacement parts for the rented equipment are the supplier's responsibility." In our reading, that matters here because K0195 is the code for leg rests on a capped rental base. Medicare.gov says that after the Part B deductible you pay 20% of the Medicare-approved amount, if the supplier accepts assignment. Medicare Advantage plans, Medicaid, the VA and private insurers set their own rules; we did not read their rules, so ask them in writing before you order. Outside the US, ask your funder or health service.

## What FDA reports and recalls show about footrests and leg rests

We ran an openFDA word search of device reports for mechanical wheelchairs (product code IOR) whose text uses the words legrest, footrest or footplate, singular or plural. It returned 1,269 reports received from 30 September 1992 to 9 October 2026, as of the database update of 4 November 2026. They are reports, not a rate of failures: the FDA calls its report database a "passive surveillance system" with "under-reporting of events, inaccuracies in reports, lack of verification that the device caused the reported event". The FDA page says the database holds voluntary reports, user facility reports, distributor reports and manufacturer reports.

The counts by year are lumpy. 2013 to 2015 held 797 of them and 2016 to 2025 only 50. In 2026 there were 267, and 264 of those name Medline (under several spellings) as the maker; the other 3 name Drive DeVilbiss, Jiangsu Jumao X-Care and TiSport. Our [manual wheelchair repair guide](https://www.mobilitatlas.com/blog/manual-wheelchair-repair-guide.html) discusses the 2026 Medline batch as a whole.

We read the first 100 of the 267 reports received in 2026, in the order the database returned them (received from 10 March to 1 September 2026). 96 are filed as malfunctions and 4 as injuries. By a word search of their event descriptions, 23 use a form of the word lock and 13 a form of the word weld. Examples: one Medline report states "the legrest will not lock into place"; another says "the weld on the left footrest of the reclining wheelchair came undone"; another states "the bracket that holds the calf pad to the leg rest broke." A report on a Drive Medical-branded wheelchair, with the maker named as Jiangsu Jumao X-Care, says the user reportedly "sustained a laceration to their right calf" while moving a leg onto a footrest. By their report numbers, 99 of the 100 are maker reports and one is a voluntary report. These are reported events, not verified causes.

Recalls tell a quieter story. An openFDA recall search for product code IOR with the same words returned 8 records from 2 recall events, in 2004 and 2008 (recall database updated 12 November 2026); none of their stated reasons names a footrest, legrest or footplate, which appear only in the product descriptions. A search of recall reasons across all product codes returned 45 records, none for product code IOR: they concern x-ray tables, beds, prosthetic and surgical devices. In our view, a latch that will not lock or a weld that cracks is a reason to stop using that rigging and call the supplier, whatever the records say.

## Three traps when you replace wheelchair footrests

Trap one: a universal part with no fit dimension. Pages that call a footrest universal or compatible with most standard wheelchairs printed no hinge spacing in the copies we saved. The one universal footplate page that printed numbers, Disability Lab's, gives a bolt range and also says which chairs it is not for. Ask for the spacing, or measure yours and ask for a written match.

Trap two: a title that names the wrong chair. The Walmart.com tile for Drive's LK3JELR says "Power Wheelchair", while Drive lists it for seven manual chairs, and Drive's Blue Streak diagram adds a serial-number caveat (see the hinge spacing section). SpinLife's Elevating Leg Rests listing included a pair of swing-away footrests. Go by the maker's model list and the item number, not the listing title.

Trap three: a part that changes the seating. A longer footrest, a different hanger angle or elevating leg rests in place of footrests change where the legs and feet sit, and the manuals tie length to clearance above the floor and pressure under the thighs. On a Tracer SX5 with push-to-lock wheel locks and extension handles, elevating legrests also bring the wheel lock warning quoted above. Ask the person who prescribed the chair before you change the type, and have them check the length after fitting.

## Three composite scenarios

These are composite scenarios, not individual customers. Each uses only the documents for that chair.

Scenario one: a Drive Silver Sport 2 with a cracked swing-away footrest. Drive's swing-away footrest page lists STDS3J24SF for the Silver Sport 2, and Drive's page prints no price without signing in. The manual says to push the front rigging lever, swing the footrest out and lift it off, and that the footrest should not be set lower than 2-1/2 inches from the ground. The Silver Sport 2 manual's warranty is three years for the original consumer purchaser, so the owner checks the purchase date and asks the dealer first.

Scenario two: an Invacare Tracer SX5 whose user's physician has recommended elevating legrests. ShopINVACARE lists T94HCP for the Tracer SX5 at a regular price of $59.00 USD on the day we read it and names the chair among eight compatible models. The Tracer SX5 manual says the user's leg must be supported by an assistant before the legrest is lowered, and that wheel lock extension handles must come off before the legrests swing aside on chairs with push-to-lock locks. Its warranty for remaining components is thirteen months, with the invoice.

Scenario three: a Ki Rogue 2 rider who wants an angle-adjustable footplate. The Rogue 2 order form lists an aluminum angle adjustable footplate (K0040) at $102 as a new-chair option, and the manual says the angle is set by loosening two screws and retightening the M6 screws to 80 in./lbs. Footrest height is set with the clinician, per the manual. Ki Mobility-made parts other than the frame and quick-release axles carry a one year warranty in North America, excluding the wear items the manual lists.

## What to ask the dealer, seller or therapist

- To the seller: which chair models does this footrest or leg rest fit, by the maker's list, and what is the hinge spacing?
- To the seller: is it a pair or one side, and does it include footplates, heel loops and calf pads?
- To the seller: what is the total with delivery to my address, and what warranty and return terms apply?
- To the maker or dealer: is my chair still under warranty, and does fitting a non-maker part affect it?
- To the therapist or seating clinician: should I keep swing-away footrests or change to elevating leg rests, and what length and footplate angle should be set?
- To the technician: can you set the length, check the floor clearance in my manual and tighten to the printed torque?

## Sources and documents

Method in brief: we saved every page used here as text with its address and read date before writing, computed the price ranges, report counts and conversions with a script from the saved text, and quoted only text that a check tool found in those files. The list of documents, with their links, follows this article. Documents read on 13 November 2026: the Invacare Tracer SX5 manual pages on front riggings; Ki Mobility's Rogue 2 manual pages on footrests and its Rogue 2 and Catalyst 5 order forms; Permobil's TiLite ZR and ZRA order form; ShopINVACARE, SpinLife, WheelchairBearings.com and Walmart.com pages; the NLM HCPCS table; and openFDA. Reused with earlier read dates: the Medline, Drive, Karman and Invacare warranty pages, Drive's accessory pages, Medline's parts guide, CMS and Medicare pages and the FDA's page on its report database.

Neighboring guides go deeper on side questions: [wheelchair parts](https://www.mobilitatlas.com/blog/wheelchair-parts-guide.html) for identifying any part, [Drive Medical wheelchair parts](https://www.mobilitatlas.com/blog/drive-medical-wheelchair-parts-guide.html) and [Invacare wheelchair parts](https://www.mobilitatlas.com/blog/invacare-wheelchair-parts-guide.html) for part numbers by catalog, [manual wheelchair repair](https://www.mobilitatlas.com/blog/manual-wheelchair-repair-guide.html) for general repairs, and [wheelchair seat upholstery](https://www.mobilitatlas.com/blog/wheelchair-seat-upholstery-guide.html) for the seat itself.

## Common questions

### Are wheelchair footrests universal?

Not on the pages we read. Makers list their footrests and leg rests by chair model: Drive's elevating leg rest page names the Drive chairs for each part number, and ShopINVACARE says its T94HCP legrests are "NOT suitable for use with Drive Wheelchairs." Pages that call a footrest universal printed no hinge spacing in the copies we saved. In our view, measure the distance between the hinge pins on your frame and ask the seller to confirm fit in writing.

### What is the difference between swing-away footrests and elevating leg rests?

In our reading, both hang on the same kind of hinge and swing aside for transfers. An elevating leg rest also has a calf pad and a locking mechanism (Medline's guide names a ratchet rod), so the leg can be raised and held. The Invacare Tracer SX5 manual says the user's leg must be supported by an assistant before an elevating legrest is lowered. Whether a person needs elevating leg rests is a question for their physician or therapist.

### How high should a wheelchair footrest be off the ground?

Follow your own manual. The Drive Silver Sport 2, Blue Streak and Viper Plus GT manuals say no lower than 2-1/2 inches from the ground, Medline's Guardian guide says no closer than 2.5 inches (6.4 cm) to the floor, and Karman's KM-5000 manual says at least 5 cm. In our view, plan on the larger figure unless the maker confirms its own in writing, and have the footrest length set with the person seated.

### Does Medicare pay for replacement elevating leg rests?

Medicare has codes for them: E0990 per elevating leg rest for an owned chair and K0195 per pair for a capped rental base, among others. LCD L33792 first requires a wheelchair that meets Medicare coverage criteria and a medically necessary accessory; it then covers elevating legrests if a musculoskeletal condition, cast or brace prevents 90 degree knee flexion, if there is significant leg edema that requires one, or if the person meets the criteria for and has a reclining back. After the Part B deductible you pay 20% if the supplier accepts assignment. Medicare Advantage, Medicaid, the VA and private plans set their own rules; we did not read them, so ask in writing.

### Why do prices for the same leg rests differ so much?

Seller pages print different prices for the same model number; our Invacare parts guide shows one example. Prices also differ by country, seller, sales period and funding, so ask each seller for a written total with delivery before you decide.

### Can Mobility Atlas quote a footrest or leg rest that is not listed on the site?

Yes. Mobility Atlas can find and quote footrests, elevating leg rests, footplates, calf pads and heel loops, including parts that are not listed. Send an enquiry or part request with the chair's make, model and serial number, the side, and photos of the hinge and footplate; you receive a written quote with delivery to your country, and nothing is charged before you accept it.

## Sources

- Invacare: Tracer SX5 wheelchair user manual, Part No. 1110550, front rigging, legrest and footplate pages (PDF, read 13 November 2026): https://status.invacareamerica.com/1110550.pdf
- Ki Mobility: Rogue 2 and Rogue XP user instruction manual and warranty, DCN0935.4 (PDF, read 13 November 2026): https://www2.kimobility.com/OwnersManuals/English-Spanish/Rogue2_XP-Eng-Spa.pdf
- Ki Mobility: Rogue2 order form, USA, DCN1017.14, effective 8/17/2026 (PDF): https://www2.kimobility.com/OrderForms/USA/Rogue2.pdf
- Ki Mobility: Catalyst 5 order form, USA, DCN0011.49, effective 8/17/2026 (PDF): https://www2.kimobility.com/OrderForms/USA/Catalyst5.pdf
- Permobil: TiLite ZR / ZRA order form, US, March 2026 (PDF): https://permobilwebcdn.azureedge.net/media/ffdharrj/us_tilite-zr-zra-2026_03-2.pdf
- Medline: Standard manual wheelchairs user guide, Guardian K1 to K4 (PDF hosted by Vitality Medical, read 9 November 2026): https://www.vitalitymedical.com/pdf/assets-1/guardian-k1-manual.pdf
- Medline: Transport chair, wheelchair and homecare bed parts guide (PDF hosted by Vitality Medical, read 12 November 2026): https://www.vitalitymedical.com/pdf/assets-2/brochure-replacement-parts-guide-medline-wheelchairs.pdf
- Drive Medical: Silver Sport 2 wheelchair page and owner's manual (read 9 November 2026): https://shop.drivemedical.com/us/en/products/mobility/wheelchairs/standard-wheelchairs/silver-sport-2-wheelchair/p/969-1
- Drive Medical: Viper Plus GT owner's manual (PDF, read 9 November 2026): https://shop.drivemedical.com/medias/1157-1?context=bWFzdGVyfGltYWdlc3wyNTEyMDd8YXBwbGljYXRpb24vcGRmfGFHSXdMMmc1WVM4eE1qWXlPREl5TkRNME5EQTVOQzh4TVRVM0xURXxhOTlmODIxMzk1NThkNWQzNTgxOGRjYTE3ZjMyYTAwNDZlZGY1ODQ2MDdjYzFkYjMwMWUzM2YyZWJhMTZlNGJj
- Drive Medical: Blue Streak wheelchair page, manual and parts diagram (read 12 November 2026): https://shop.drivemedical.com/us/en/products/mobility/wheelchairs/standard-wheelchairs/blue-streak-wheelchair/p/978-1
- Drive Medical: Swing-Away Footrests page (read 12 November 2026): https://shop.drivemedical.com/us/en/products/mobility/wheelchairs/accessories/swing-away-footrests/p/1215-1
- Drive Medical: Swing-away Elevating Leg rests page (read 12 November 2026): https://shop.drivemedical.com/us/en/products/mobility/wheelchairs/accessories/swing-away-elevating-leg-rests/p/1226-1
- Drive Medical: Heel loops page, STDS831 (read 12 November 2026): https://shop.drivemedical.com/us/en/products/mobility/wheelchairs/accessories/heel-loops/p/1254-1
- Karman Healthcare: LT-1000 transport wheelchair page and user guide (read 9 November 2026): https://www.karmanhealthcare.com/product/lt-1000-transport-wheelchair/
- Karman Healthcare: KM-5000 (MVP 502 series) manual (PDF, read 9 November 2026): https://www.karmanhealthcare.com/wp-content/uploads/2013/01/KM-5000_Manual.pdf
- ShopINVACARE: Invacare wheelchair legrests, elevating, composite footplates, padded calf pads, 1 pair (T94HCP): https://shop.invacareamerica.com/products/invacare-wheelchair-legrests-elevating-composite-footplates-padded-calf-pads-1-pair
- SpinLife: Footrest Assemblies listing: https://www.spinlife.com/parts/manual-wheelchair-parts/footrests-and-leg-rests/footrest-assemblies/critpath/match.cfm?categoryID=711
- SpinLife: Elevating Leg Rests listing: https://www.spinlife.com/parts/manual-wheelchair-parts/footrests-and-leg-rests/elevating-leg-rests/critpath/match.cfm?categoryID=710
- SpinLife: TiLite Flip-Up Footrest Assembly (AS100230-Z): https://www.spinlife.com/TiLite-Flip-Up-Footrest-Assembly-Foot-Plates/spec.cfm?productID=102276
- SpinLife: Proactive Medical Swing Away Foot Rests (Pair), PP-SF: https://www.spinlife.com/Proactive-Medical-Swing-Away-Foot-Rests-%28Pair%29-Elevating-Leg-Rests/spec.cfm?productID=180968
- WheelchairBearings.com: Wheelchair Footplates and Footrests collection: https://wheelchairbearings.com/collections/wheelchair-footplates-and-footrests
- WheelchairBearings.com: Disability Lab universal wheelchair footplate 10 x 7 in, rear bolt flip up: https://wheelchairbearings.com/products/girl-power-universal-wheelchair-footplate-10-x-7-rear-bolt-flip-up
- Walmart.com: search results for wheelchair elevating leg rests, first page: https://www.walmart.com/search?q=wheelchair+elevating+leg+rests
- Walmart.com: drive Elevating Legrest LK3JELR, 1 pair: https://www.walmart.com/ip/drive-Elevating-Legrest-For-drive-Power-Wheelchair-LK3JELR-1-Pair/214992856
- National Library of Medicine: HCPCS lookup, footrest: https://clinicaltables.nlm.nih.gov/api/hcpcs/v3/search?terms=footrest&df=code,display,long_desc&maxList=30
- National Library of Medicine: HCPCS lookup, legrest, footplate, heel loop, calf and single codes: https://clinicaltables.nlm.nih.gov/api/hcpcs/v3/search?terms=legrest&df=code,display,long_desc&maxList=30
- CMS: LCD L33792, Wheelchair Options/Accessories, version 43 (read 9 November 2026): https://www.cms.gov/medicare-coverage-database/view/lcd.aspx?lcdid=33792&ver=43
- CMS: LCD L33792, future version effective 12/20/2026 (read 9 November 2026): https://www.cms.gov/medicare-coverage-database/view/lcd.aspx?lcdid=33792
- CMS: Article A52504, Wheelchair Options/Accessories policy article, version 61 (read 9 November 2026): https://www.cms.gov/medicare-coverage-database/view/article.aspx?articleid=52504&ver=61
- Medicare: Medicare Coverage of Durable Medical Equipment and Other Devices, booklet 11045 (read 9 November 2026): https://www.medicare.gov/publications/11045-medicare-coverage-of-dme-and-other-devices.pdf
- Medicare.gov: Wheelchairs and scooters coverage page (read 9 November 2026): https://www.medicare.gov/coverage/wheelchairs-scooters
- openFDA: device reports, product code IOR, word search for legrest, footrest and footplate, counts by date received: https://api.fda.gov/device/event.json?search=device.device_report_product_code:IOR+AND+mdr_text.text:(legrest+OR+legrests+OR+footrest+OR+footrests+OR+footplate+OR+footplates)&count=date_received
- openFDA: device reports, same search, received in 2026, counts by maker: https://api.fda.gov/device/event.json?search=device.device_report_product_code:IOR+AND+mdr_text.text:(legrest+OR+legrests+OR+footrest+OR+footrests+OR+footplate+OR+footplates)+AND+date_received:[20260101+TO+20261231]&count=device.manufacturer_d_name.exact
- openFDA: device reports, same search, received in 2026, first 100 records: https://api.fda.gov/device/event.json?search=device.device_report_product_code:IOR+AND+mdr_text.text:(legrest+OR+legrests+OR+footrest+OR+footrests+OR+footplate+OR+footplates)+AND+date_received:[20260101+TO+20261231]&limit=100
- openFDA: device recalls, product code IOR, word search for legrest, footrest and footplate: https://api.fda.gov/device/recall.json?search=product_code:IOR+AND+(reason_for_recall:(legrest+OR+legrests+OR+footrest+OR+footrests+OR+footplate+OR+footplates)+OR+product_description:(legrest+OR+legrests+OR+footrest+OR+footrests+OR+footplate+OR+footplates))&limit=100
- openFDA: device recalls, all product codes, recall reasons naming legrest, footrest or footplate: https://api.fda.gov/device/recall.json?search=reason_for_recall:(legrest+OR+legrests+OR+footrest+OR+footrests+OR+footplate+OR+footplates)&limit=100
- FDA: About the MAUDE database (read 9 November 2026): https://www.fda.gov/medical-devices/mandatory-reporting-requirements-manufacturers-importers-and-device-user-facilities/about-manufacturer-and-user-facility-device-experience-maude-database

Read on 13 November 2026. The wording of the article is our own.

## About the author

Mobility Atlas is run by Anna, who has used a wheelchair for 19 years, since she was ten. She started it because she always wanted one place where a person who needs a chair, a wheel, a cushion or a spare part can see everything that is made, side by side, and simply ask for it. She reads and answers every enquiry herself.

Contact: anna@mobilitatlas.com, WhatsApp +66 65 398 9085. Canonical facts about Mobility Atlas: https://www.mobilitatlas.com/about/facts.html
