# Wheelchair brakes replacement in 2026: wheel locks compared, push, pull and scissor locks, grade aids, brake extension handles, fitting, prices and warranty

Source: https://www.mobilitatlas.com/blog/wheelchair-wheel-lock-guide.html
By Anna, founder of Mobility Atlas (https://www.mobilitatlas.com/about/). Published 13 November 2026.

Replacing wheelchair brakes: wheel lock types, clamps and tube sizes, the depth into the tire as manuals print it, extension handles, grade aids, US prices and warranty.

## In short

- Wheel locks hold a stopped chair; they are not brakes. 8 of the 11 manuals, guides and maker articles we read say so; the Drive Silver Sport 2 and Viper Plus GT manuals say not to use them to slow your descent down an incline, and Motion Composites' unilateral installation sheet does not address it.
- Replace like for like: same style (push-to-lock, pull-to-lock, scissor, one-lever or grade aid), same side, and a clamp that fits your frame tube, which seller pages list as 1 inch or 1.25 inch.
- Set the depth into the tire your documents print: at least 1/8 inch in the Medline Guardian, Drive Silver Sport 2 and Viper Plus GT and Quickie Nitrum manuals, at least 1/8 inch (3/16 inch for pneumatic tires) in the Invacare Tracer SX5 manual, at least 3/16 inch in Out-Front's guides, with the tire inflated first.
- On 12-13 November 2026 complete locks, pairs and grade aids at three US sellers ran from $48.00 (one Out-Front lock, no clamp) to $149.99 (a pair of aluminum push-to-lock levers), leaving out a $996.00 one-handed system, brake pads, extensions, mounts, grips and spare kits; a pair of clamps added $82 to $101; extension handles were $39.99 (generic) and $84.99 (TiLite) a pair at WheelchairBearings.com, and "Starting at $50" each (ProActive) at SpinLife.
- Which style, extension or grade aid suits you is a question for your therapist after a trial; warranties differ by document: one year on parts in the Ki Rogue 2, Quickie Nitrum and Medline Guardian manuals and Motion Composites' terms, thirteen months in the Invacare Tracer SX5 manual, three years in the Drive Silver Sport 2 manual.

## The short answer

Wheelchair wheel locks are the levers beside the rear wheels that press a shoe or arm into the tire so a stopped chair stays put. Many people call them brakes, and in this guide wheelchair brakes replacement means fitting a new wheel lock, a clamp or a wheel lock extension handle. The manuals are blunt about the name. The Invacare Tracer SX5 manual says: "DO NOT attempt to stop a moving wheelchair with wheel locks. Wheel locks are not brakes." This guide compares the wheel locks that makers and US sellers list in November 2026: push-to-lock, pull-to-lock, scissor and under-seat locks, one-lever locks, grade aids, attendant and drum brakes and extension handles. It covers how each one mounts and is adjusted as the manuals print it, which part numbers belong to which chair, what they cost and what the warranties say.

Which wheelchair wheel lock should you buy as a replacement? Usually the same style, side and mounting as the one on your chair now, because the lock must fit the frame tube, line up with the tire and suit how you transfer. Mobility Atlas read ten maker manuals and installation guides, two order forms and the listings of three US sellers on the dates given below. On those pages a replacement lock is sold by style (push or pull to lock, scissor, grade aid), by side (left or right, or a pair), and by mount (with or without a clamp sized to the tube). Complete locks, pairs and grade aids on the seller pages ran from $48.00 for one Out-Front composite lock without a clamp to $149.99 for a pair of aluminum push-to-lock levers; the range leaves out a $996.00 one-handed system, brake pads, extension handles, mounts, grips and spare kits.

Three questions settle most choices: do you push or pull more easily, are your rear tires pneumatic or solid, and do you need help on ramps?

The first question belongs partly to a clinician. Which lock style suits your hands, your balance and your transfers, and whether you need an extension handle or a grade aid, is a decision to make with your occupational therapist, physical therapist or seating clinician, ideally after trying the lock on a chair. This guide explains the options, what each maker's document says and what to ask, and then stops.

## How we compared, and our interest

Mobility Atlas earns a fee or margin when you order through us; the comparison below uses the makers' published documents, sellers' listings, public FDA and Medicare records. We did not buy, fit or test any wheel lock, and we did not ask any maker or seller a question.

Our method was simple. On 13 November 2026 we opened each page named below in a browser and saved its text, with the address and the date, before writing. For PDF manuals, guides and order forms we extracted the text in the browser and saved the pages that deal with wheel locks, marking the gaps. Several documents were saved a few days earlier by our team and are reused with their own read dates: the Quickie Nitrum manual, the Medline Guardian user guide, the Drive Silver Sport 2 and Viper Plus GT manuals, the Karman LT-1000 documents, Medicare's rules and the FDA page on its report database were read on 9 November 2026; Drive's wheel lock extension page, the wheel lock page of Invacare's Tracer parts catalog, SpinLife's wheel lock listing and Medline's parts guide were read on 12 November 2026. Where we did arithmetic, such as a pair price from a per-lock price or a conversion from inches to millimeters, a script computed it from the saved text.

The makers' documents read on 13 November 2026 were: Invacare's Tracer SX5 user manual (the wheel lock pages); Ki Mobility's Rogue 2 and Rogue XP manual and its Rogue 2 order form; Permobil's TiLite ZR and ZRA order form dated March 2026; Out-Front's installation and user guides for its composite push-to-lock and pull-to-lock locks, which Sportaid hosts; Motion Composites' installation sheet for its unilateral wheel lock and its article on wheel lock types. The sellers were Sportaid (its Brakes category and seven product pages, and the first page of its wheel lock search), SpinLife (four product pages) and WheelchairBearings.com (its wheel lock collection). All three are US sellers and the prices are in US dollars. We also ran an openFDA word search of device reports and recalls.

Where two documents give different figures for the same thing, such as how far a lock must press into the tire, we give both and say which document printed which. Where a page gives no figure, we say so. Prices checked November 2026. Documents checked November 2026.

## Wheel locks are not brakes: what the manuals say

The documents we read agree on one point before anything else: a wheel lock holds a chair that has already stopped. It does not slow a moving chair. Of the 11 user manuals, installation guides and maker articles we read, a word search by script finds 8 that say wheel locks are not brakes, in some form; the 2 Drive manuals say instead not to use them to slow your descent down an incline, and Motion Composites' unilateral installation sheet does not address it. Here is the wording, document by document.

- Invacare Tracer SX5 manual: "DO NOT attempt to stop a moving wheelchair with wheel locks. Wheel locks are not brakes." The same safety page adds: "Engaging the wheel locks may not prevent the wheelchair from moving on all floor surfaces including those that may be wet or slick."
- Ki Mobility Rogue 2 manual: "Wheel locks are not to be used as brakes to slow or stop your wheelchair. Using a wheel lock as a brake could cause loss of control or a fall resulting in serious injury or death."
- Quickie Nitrum manual, in its section on rear wheel locks: "Rear wheel locks are NOT designed to slow or stop a moving wheelchair." It says to use them "only to keep the rear wheels from rolling when your chair is at a complete stop."
- Medline's Guardian user guide says: "DO NOT use the wheel locks to stop the wheelchair from moving. Wheel locks are not brakes. DO NOT use the wheel locks to slow your descent down an incline."
- Out-Front's guides for its composite locks say: "Out-Front wheel locks are NOT designed to slow or stop a moving wheelchair - they are NOT brakes."
- Karman's user guide says: "Wheel locks are designed to prevent the rear wheels from turning when the chair is stopped. It is not intended to slow down the chair when it is moving."
- Motion Composites' article on wheel lock types says wheel locks "are not used to stop a moving wheelchair" and that they "keep a stationary wheelchair stationary, occupied or not."

Both Drive manuals give the reason in their paragraph on ramps: "Attempting to use the wheel lock brakes could result in accidental locking, tipping to one side, or cause a sudden stop." The same paragraph says: "Correct techniques on ramp negotiation should be shown to you by a qualified professional." In our view, the parts built to slow a chair are attendant brakes and drum brakes on chairs that have them; how to take a slope is technique for your therapist to show you. A grade aid stops rolling backward, not forward.

Where do the manuals say to lock the chair? The Medline guide says to engage the wheel locks "on both wheels before entering the chair, leaving the chair, leaning forward in the chair or while being transported in an elevator or a wheelchair lift." The Nitrum manual says: "To keep the rear wheels from rolling, always set both rear wheel locks when you transfer to or from your chair." The transfer technique itself belongs to your therapist; the Medline guide, for example, says not to transfer on your own unless you have been "instructed in transfer techniques by a health professional".

## Wheelchair wheel locks at a glance: the core table

The table lists the wheel lock types we found on the makers' and sellers' pages we read, with one or two examples each and a price we saw, in US dollars, as printed on the date we read the page. An order form price is the price of that option on a new chair, not a spare part price. Each row's details are in the sections that follow.

| Type | How it engages | Where it sits | Example seen | Price seen |
| --- | --- | --- | --- | --- |
| Push-to-lock | Handle pushed forward | Side frame, above tire | Out-Front composite (Sportaid) | $48.00 one lock, no clamp |
| Pull-to-lock | Handle pulled back | Side frame, above tire | Out-Front composite (Sportaid) | $48.00 one lock, no clamp |
| Scissor | Single action lever | Below the seat (Motion article) | MBL aluminum (Sportaid) | $79.00 one lock, no clamp |
| Under-seat scissor | Not described | Under seat (form name) | Ki Rogue 2 order form | $37 option |
| Unilateral lock | One lever, tension cables | Clamps on both sides | Motion Composites sheet | No price read |
| Grade aid | Lever down, stops rollback | Side frame, on tire | Newton Grade Aid (SpinLife) | $112.00 |
| Extension handle | Slips over lock handle | On the lock lever | ProActive 6 in (SpinLife) | Starting at $50.00, each |
| Attendant brake | Hand lever or loop | Rear of the chair | Karman LT-1000HB | No price read |
| Drum brake | Squeeze levers | Worked by levers (Ki manual) | Ki Rogue 2 manual | No price read |

Two notes on the table. First, one lock means one side: the Out-Front pages sell a left or right lock at the price shown, a pair option that adds $48 ($96.00 by our arithmetic), and a clamp is a separate option. Second, the unilateral, attendant and drum brake rows have no price because we did not find a seller page for them on the sites we read; the documents we have describe how they work, not what they cost.

## Push-to-lock and pull-to-lock wheel locks

Motion Composites' article calls push and pull locks "The most common types of wheel locks". A handle on the side frame moves a shoe or bar into the tire. On a push-to-lock you push the handle forward to lock; on a pull-to-lock you pull it back toward you. The Invacare Tracer SX5 manual's drawing spells out the motion: for push-to-lock, "Push wheel lock handle forward away from the tire to engage wheel lock", and for pull-to-lock, "Pull wheel lock handle backward toward the tire to engage wheel lock".

Which one is easier depends on your arms and how you transfer. Motion Composites' article on wheel lock types says: "Push to lock is generally a safer option for transfers because the handle is pushed down and away when engaged." It adds that "Clients with stronger pulling ability may find the pull to lock wheel lock easiest to operate", and warns that "Some may find interference with push to lock wheel locks and swing away leg rests." These are a maker's general points; which suits you is a question for a trial with your therapist.

What the makers list. Sportaid sells Out-Front's push-to-lock (stock number OF-3RLOCKPS) and pull-to-lock (OF-3RLOCKPL). Each page lists a left lock, a right lock and a pair, all without a clamp, and four clamp choices: 1 inch or 1.25 inch, each or pair. Sportaid's page says the fiber reinforced composite "reduces wheel lock weight by 49% compared to standard aluminum wheel locks"; the page gives no weight in grams or ounces. Quickie push-to-lock brakes are listed by Sportaid as stock number 9078, "Price is per pair", with a note that "Some wheelchair models require different styles."

Motion Composites' Newton push locks are sold by side at SpinLife: model 41056 for the left and 41057 for the right. SpinLife's record for the left lock says the composite lock weighs "1.3 oz. less than traditional wheel locks" and that a 6 inch extension handle is also available for the lock. Motion Composites' own article gives the same saving as "1.3 ounces (38 grams)" and says Newton locks use "reverse tread screws on one side of the chair" to resist loosening. The left lock's record lists a standard version (41056) and a 6 inch extension version (item 9002216).

Generic universal locks also exist. SpinLife lists ProActive Medical's Universal Wheel Lock Assembly (PP-RWLAC), push-to-lock, left or right. SpinLife's page describes it as "Designed to be compatible with a wide range of standard manual wheelchairs" but names no chair it fits and no tube size. In our view, a lock that names no chair and no tube size is one to check against your old lock in hand, with your dealer, before you order.

### Push or pull: what the manuals add

The Tracer SX5 manual warns about one combination. On a chair with push to lock wheel locks, elevating legrests and wheel lock extension handles, it says "the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side", because the top of the legrest can knock the lock off. The Medline guide says to "Check to make sure that the legrests do not unlock the wheel locks when they are swung back." In our view, if your chair has swing-away legrests, test this after fitting any new lock: lock the chair with nobody seated, take off any extension handles first, as the Tracer SX5 manual requires on chairs with push to lock wheel locks and elevating legrests, then swing the legrest and check that the lock stayed on.

## Scissor and under-seat locks

Sportaid's scissor pages say the "single action lever retracts to a position that is completely away from the tire and wheel". Motion Composites' article says: "The low profile scissor lock is positioned below the seat, keeping the device out of the path of transfer and the path of propulsion." The article goes further and calls it "the safest wheel lock to prevent injury to the user"; that is the maker's claim. In our view, the trade-off is reach, because the lever sits lower.

The scissor locks on the seller pages we read are these. Sportaid lists the MBL Performance Aluminum Scissor Lock (stock MBLPASL) at $79.00 for one side, with part numbers 8717-L and 8717-R and a pair option; its page says it "Fits most ultralights with 1″ or 1-1/4″ tubing". Sportaid also lists the Out-Front MBL Composite Scissor Wheel Locks (OF-3RMBLLOCK) at $78.25 for one side. That page says "Fits most ultralights with 1″ or 1-1/8″ tubing", but its clamp options are 1 inch and 1.25 inch. The two figures differ, so in our view ask the seller in writing which clamp fits your tube before you order, and plan on the tube size the clamp option names.

For Quickie chairs Sportaid lists "Scissor Wheelchair Brakes with Clamp for Quickie" (stock 9077, $81.50, "Priced per pair") and a version with clamp and long arm (9077L, $100.00, "Price is per pair"). The long arm page notes that "these are no longer available for the Quickie GT". Both pages ask for your chair's make and model before the order can be processed.

WheelchairBearings.com lists Reckless Wheelchairs' micro adjustable aluminum scissor brakes as a pair in black, red or blue, each tile at $144.99 for the pair against an original price of $174.99 on the collection page. The same collection sells spare parts for scissor locks: an Eagle scissor brake reverse kit at $9.99, a spring and bumper replacement kit at $14.99 and replacement slider nuts for the Reckless brakes at $19.99. In our view, a spare spring or bumper can be the cheaper repair when the arm itself is sound.

On new chairs the order forms price scissor locks as options. The page of Ki Mobility's Rogue 2 order form lists an Under Seat Scissor Lock at $37 ("Not available with User Activated Anti-Tips") and a Low Profile Scissor Lock at $68 ("Not available with Full Poly tires"), against no charge for push or pull to lock. TiLite's ZR and ZRA order form lists the MBL Composite Scissor Lock (ZWLK11) at $158.00 and the MBL Performance Aluminum Scissor Lock (ZWLK12) at $175.

## One-lever locks: Uni-Lock, unilateral and one-handed systems

Some people can reach only one side of the chair, or have use of one hand. Some makers offer locks worked from one lever. TiLite's ZR and ZRA order form also lists a "Uni-Lock" (ZWLK3) at $179.00, without saying how it works, with "Push" and "Pull" choices printed under it, and separate extension handles for it (ZWLK4, $93.00, coded E0961). We did not find a TiLite manual page for it, so we describe it no further.

Motion Composites publishes an installation sheet for its "Unilateral wheel lock" (MC-MKTG-WI-0026, revision date 17/05/2022). The drawing labels a wheel lock mechanism engagement lever, a tension adjustment and "Tension cables", and the steps say to "Pass the tension cables behind the crossbrace" and to repeat the clamp steps on the other side. The materials list names the unilateral wheel lock itself (0004570A-00) and two kinds of brake clamp, 0041017A-00 and 0041501A-00, and the steps print torque values by frame: 7 Nm for carbon, 12 Nm for aluminum. On a carbon frame the clamp goes 2 inches from the wheel lock rail (the sheet prints 2’’), while "On the aluminium frame, the clamp can be installed anywhere without restriction." It also explains how to change a right unilateral lock to a left one by flipping the lever. Its compatibility tables are images that did not extract, so we cannot say which Motion chairs accept it.

WheelchairBearings.com lists the "PUSH LOX One-Handed Wheelchair Locking System" at $996.00, the highest price in that collection. Its product page on the same site (read 13 November 2026) describes a "patented LEVER and HUB LOCK design" using standard bike cables, says it is "Made to Fit these Spinergy Wheels" and lists 11 Spinergy wheel models, with main tubing sizes from 3/4 inch (19mm) to 1.25 inch (32mm). It names no other wheels, so in our view do not assume it fits other wheels; ask the seller in writing.

In our view, a one-lever lock is a decision for you and your therapist or seating clinician; ask the dealer for the maker's instructions for your exact chair before ordering.

## Grade aids and hill holders

A grade aid, also sold as a hill holder or anti-rollback device, lets the wheels turn forward but not backward, so you can rest on a ramp without rolling back. Ki Mobility's Rogue 2 manual says: "Grade Aids are an assistive device to prevent wheelchair roll back when traveling on an incline such as a hill or ramp." Its steps are two lines: "Engage the Grade Aid to prevent roll back by pushing down on the lever end." and "Disengage by pulling upward on the lever."

What does a grade aid not do? In our reading, it does not slow you going downhill, and it is not an anti-tipper. Motion Composites' article says that, when engaged, "the grade aid device prevents the wheelchair from rolling backwards while maintaining unobstructed forward movement." It also says: "Space on the side frame must be shared by both the grade aid device and the wheel lock." In our reading, that is why Newton sells a combined unit. SpinLife's record for the Newton Grade Aid Wheelock (model 900) says it "disengages to prevent thumb injury" and that "The unit weighs only 156gm versus a 225gm conventional lock"; a script puts that gap at 69 g, or 30.7 percent of the conventional lock's weight, close to the "30% weight saving" SpinLife's bullets print. Motion Composites' article says the combination unit has "three positions, free wheel, grade aid, and wheel lock."

Tire type limits grade aids on the order forms we read. Ki's Rogue 2 form says its Grade Aids option (E0974, $157) is "Available only with Push to Lock Wheel Locks and Pneumatic or Pneumatic with Airless Insert tires". TiLite's form lists Grade Aids Push to Lock (ZWLK15, $190.00) as "Not available with solid rear tires." On SpinLife, the Newton Grade Aid was $112.00 against a struck price of $150.00, sold as a left or a right unit (items 9001582 and 9001581).

One FDA report involves an anti-rollback device and a tip-over. By a word search of device reports filed under FDA product code IOR, which FDA names "Wheelchair, Mechanical", for grade aid, hill holder and anti-rollback, the openFDA database (last updated 4 November 2026) returned one report, received in 2005 and filed by the maker. It states that a facility had installed an anti-rollback device on a wheelchair as a demonstration unit and that the resident was later found with the chair tipped over; the event type is recorded as a death. The maker's narrative says "IT APPEARS THE EVENT WAS THE RESULT OF A TIP OVER" and that "PRODUCT WAS NOT AND IS NOT DESIGNED TO BE AN ANTI-TIP DEVICE." One report proves no cause, and we do not draw one; in our view it is a reason to ask your therapist whether you also need anti-tippers before adding a grade aid.

## Attendant brakes, drum brakes and hub locks

These are the parts that can slow a moving chair, and they are different from wheel locks. Three kinds appear in the documents we read.

Attendant hand brakes are for the person pushing. Karman's LT-1000 product page mentions "companion hand brakes, which allows caretakers to safely and smoothly bring the wheelchair to a controlled stop, as well as engage a parking brake to assist in safe transfers." Its literature sheet lists a "Hand loop brake system for attendant" and, separately, "Manual lock brakes". In our reading, the chair has both: loop brakes for the attendant and ordinary wheel locks. Motion Composites' article describes attendant wheel locks more generally: "The attendant lock is mounted to the rear of the wheelchair in order to be operated by a caregiver standing behind the chair." It adds that some are worked by hand and others by foot.

Drum brakes are worked by levers. Ki Mobility's Rogue 2 manual has a section on them. Its operating steps say to squeeze the brake levers on both sides to brake, and: "Each side is operated independently and may be squeezed with more or less force to get more or less braking action." For parking, the manual describes squeezing each lever and flipping a locking lever into the teeth on the lever mount. Its warning reads: "Using your wheelchair without properly adjusted drum brakes can affect the stability of the wheelchair causing a loss of control resulting in serious injury." The adjustment is done with a 10mm wrench at a jam nut and adjuster; the manual says: "It is recommended to adjust the brake until there is a slight bit of drag on the wheel when spun." It then says to thread the adjuster inward until all drag is gone, and ends by checking that the brake, fully on, still holds the occupied chair.

Hub locks lock the wheel at its hub rather than at the tire. Motion Composites' article says: "Hub locks utilize a piston at the end of a cable to engage the locking mechanism at the wheel's hub." It says they "work regardless of changes in wheel size, tire tread, or tire pressure." The only hub lock product page we read is the Push Lox page described above.

One recall returned by our word search concerns a hub brake. By a word search of recalls under product code IOR for brake or lock, openFDA (last updated 12 November 2026) returned one record: Invacare's recall Z-0785-2013 of the Solara 3G custom manual wheelchair, initiated on 10 September 2012 and now terminated, for 3 units with three listed serial numbers. The reason is printed as: "The potential exists for the wheel to rotate freely despite engagement of hub brake." The fix was a retrofit kit fitted by the provider. In our view, the record is a reminder that a brake of any kind needs testing after it is fitted.

In our view, if a manual chair has drum brakes or attendant brakes, have the dealer's technician adjust and replace their cables and pads unless the manual shows you how, because these are the parts that slow the chair.

## Wheelchair brake extension handles

How do you choose a wheelchair brake extension handle? Start with the lock you have: an extension slips over the lock's handle so it is easier to reach and needs less force, and the pages we read sell them for named lock families. Mobility Atlas read the Ki Mobility and Invacare manuals, two order forms and three sellers' pages on 13 November 2026, and Drive's extension page and Invacare's parts catalog page on 12 November. Invacare's Tracer SX5 parts catalog lists a 6 inch black extension (1058899); Drive's page ties STDS601, STDS801 and STDS801GT to named chairs; Ki's form prices extension handles at $88 and TiLite's at $93.00 on a new chair. SpinLife lists a ProActive extension at $50.00 for 6 inches and $55.00 for 8 inches, and a pair of generic 6 inch extensions with lanyards at $39.99. Ki's manual says to remove extensions for transfers; the Tracer SX5 manual, on chairs with push-to-lock locks and elevating legrests, before swinging the legrests aside.

How they fit, as the documents print it. The Tracer SX5 manual's steps are two: "Remove the existing rubber tip from the wheel lock handle" and "Install the extension handle over the wheel lock handle". Ki's manual says: "Wheel Lock Extension Handles are designed to slip over the existing wheel lock handle to provide better access to the wheel lock and increase leverage during activation and deactivation." Motion Composites' article says: "These extensions are often removable for transfers but often remain tethered to the chair." In our reading, that is why some seller listings include a lanyard.

When they must come off. Ki's manual says: "Extension handles should be removed during transfer to ensure wheel locks are not deactivated." The Tracer SX5 manual's warning covers chairs with push to lock wheel locks, elevating legrests and extension handles: the handles "MUST be removed before swinging the elevating legrests to the side". The manual prints this warning on three pages, and they differ by one word: the safety page and the extension handle page say the interference "causes the wheel lock to disengage"; the operation page says it "may cause the wheel lock to disengage." In our view, treat it as the stronger version.

### Which extension for which lock

Fit is by lock family, and the pages say so in different ways. TiLite's order form lists ZWLK10, "Extension Handles for Compact Composite Push/Pull to Lock", and ZWLK4, "Extension Handles for Uni-Lock". Ki's form says its extension handles are "Available only with Push to Lock or Pull to Lock Wheel Locks". SpinLife's Newton push lock record lists a 6 inch extension version. WheelchairBearings.com's product page for TiLite's extensions with lanyard (read 13 November 2026) says they "fit all current TiLite wheelchairs with composite (Out-Front) wheel locks" and prints TiLite part numbers CP105920 and RW100214 (lanyard). That pair was $84.99, which is $45.00 more than the generic pair at $39.99.

For Drive chairs, Drive's Wheel Lock Extensions page (read 12 November 2026) ties each item number to a list of chairs; our [Drive Medical parts guide](https://www.mobilitatlas.com/blog/drive-medical-wheelchair-parts-guide.html) covers them. For Medline chairs, Medline's parts guide lists a "Brake Extender", MDS85157PR, in the accessory lists that follow its Excel 2000 and K4 Lightweight tables. For the ProActive extension, SpinLife's page says it is "compatible with most standard manual wheelchairs" and names none; SpinLife lists it with "No Warranty" and a 20% restocking fee.

## How a wheel lock mounts: clamps, tube sizes and hardware

The seller pages we read sell locks with or without a clamp that fits the frame tube's outside diameter; the Tracer SX5 manual's patient operated locks are secured by a bolt and locknut, and its clamp-on locks by a "bolt and locknut or socket screws". Out-Front's push, pull and scissor pages on Sportaid offer clamps for 1 inch or 1.25 inch tubing, at $41 each or $82 a pair for 1 inch and $50.5 each or $101 a pair for 1.25 inch. WheelchairBearings.com lists a pair of Top Gear brake mounts for 1 inch and 1.25 inch tubing at $39.99. The Push Lox product page prints main tubing sizes from 3/4 inch (19mm) to 1.25 inch (32mm). A script converts the two common sizes: 1 inch is 25.4 mm and 1.25 inch is 31.8 mm.

How to measure, in our view: use calipers on the frame tube where the old clamp sits, not on the clamp. The documents we read give no clamp for oval tubes, so for those ask the maker's dealer.

How the clamp goes on: each Out-Front guide for its composite push-to-lock and pull-to-lock locks says: "Place the wheel lock clamp onto the frame and slightly tighten one of the two Allen screws that secure the wheel lock clamp to the frame." Then: "Slide the wheel lock into the wheel lock clamp." Then adjust the clamp's position for the depth into the tire and "Securely tighten the two Allen screws". The tool named is a 3/16 inch Allen wrench. The guides add that, depending on rear wheel spacing and center of gravity, "it may be necessary to use an extended clamp or an offset clamp."

Ki Mobility's Rogue 2 manual uses a 5mm Allen wrench and gives a note on technique: "Always loosen and tighten wheel hardware by alternating between the two bolts while loosening/tightening a little at a time." The manual says this prevents overclamping on one set of hardware. Motion Composites' unilateral lock sheet prints torque values: 7 Nm on a carbon frame and 12 Nm on an aluminum one, and Ki's maintenance table says that, unless otherwise noted, fasteners "should be tightened to 40 in./lbs (4.51 N*m)." These values belong to those two documents; Out-Front's guides print no torque and say "Securely tighten the two Allen screws". The Invacare Tracer SX5 manual adjusts its locks at a bolt and locknut, and the Drive manuals at the nut on a carriage bolt; the Drive manuals say "Adjustments to locks are made by loosening or tightening nut on the carriage bolt."

Why locks work loose. Motion Composites' article says: "Over time, the rotation of the wheel lock assembly will result in the gradual loosening of the screws on one side of the chair." Our [manual wheelchair repair guide](https://www.mobilitatlas.com/blog/manual-wheelchair-repair-guide.html) found loosening to be the most common wheel lock problem in the FDA reports it read; it covers the checks in detail, so we do not repeat them here.

## Adjusting the depth: how far the lock must press into the tire

All but one of the adjustment sections in the table below set one measure: how far the lock's shoe or arm presses into the tire when it is on. The documents do not agree on the number, and they tie it to tire type in different ways. Here is each one as printed.

| Document | Depth into the tire, as printed | Tire condition |
| --- | --- | --- |
| Medline Guardian user guide | at least 1/8 in (3.2 mm) | Not stated |
| Drive Silver Sport 2, Viper Plus GT | at least 1/8 in | Not stated |
| Quickie Nitrum manual | at least 1/8 in | Low pressure noted (lock may slip) |
| Invacare Tracer SX5 manual | at least 1/8 in (3/16 in for pneumatic) | Inflate to sidewall psi first |
| Out-Front composite lock guides | at least 3/16 in | Inflate to sidewall pressure first |
| Ki Mobility Rogue 2 manual | No figure: compresses the tire | Tire wear and pressure noted |

A script converts the two figures: 1/8 inch is 3.2 mm and 3/16 inch is 4.8 mm. The Tracer SX5 manual's wording is: "the wheel lock shoe embeds the tire 1/8 inch (3/16 inch for pneumatic tires) and holds the wheelchair." The Out-Front guides say the wheel stop must embed at least 3/16 inch into the tire "or the chair may roll unexpectedly." Where your manual and the lock's guide differ, in our view, plan on the larger depth that still lets the lock engage and release by hand, and ask the dealer to confirm in writing.

The steps, as the Tracer SX5 manual prints them for its patient operated locks, with the chair on "a flat, level surface" as it says: open the lock; loosen the bolt and locknut; reposition the lock to the depth above; tighten; engage the lock; "Measure the distance the wheel lock is embedded into the tire"; repeat until it holds; do the other side; then "Engage both wheel locks and ensure the occupied wheelchair is held in place when pushed." Ki's manual ends its steps with: "Always test new wheel lock positioning on a flat level surface." The Drive manuals end with: "Test for correct locking action before actual use."

When it still will not hold. The Tracer SX5 manual is clear: "If wheel locks do not hold the occupied wheelchair in place, contact a qualified technician; otherwise injury or damage may occur." Ki's manual says: "If there is any doubt as to the continued safe use of your wheelchair or if any parts should fail or appear to be near failure, stop using the device immediately and contact your authorized representative immediately." In our view, follow those lines as printed: if the lock does not hold, stop using the chair and contact the dealer or a qualified technician.

## Tire pressure, tire wear and axle changes

A wheel lock presses on the tire, so anything that changes the tire changes the lock. The manuals list three causes.

Pressure. The Nitrum manual says: "Low pressure in a rear tire may cause the wheel lock on that side to slip and may allow the wheel to turn when you do not expect it." The Out-Front guides say the same and add a rule for fitting: "If you adjust the locks when the tires are under-inflated, the lock will not operate properly when the tire is fully inflated." The Tracer SX5 manual says to inflate pneumatic tires to "the recommended psi on the side wall of tire" before adjusting or replacing the locks. The Tracer SX5 manual, the Out-Front guides and Ki's maintenance table send you to the tire's sidewall for the pressure. Our [tire and caster care guide](https://www.mobilitatlas.com/blog/tire-caster-care.html) covers the pressure check itself.

Wear. Ki's manual warns: "Underinflated or worn tires may cause your wheel locks to not function properly." Its maintenance table says: "Tire pressure changes and tire wear will require the wheel locks to be adjusted." In our view, re-check the depth into the tire after fitting new tires too.

Axle position and wheel size. The Nitrum manual says: "Adjust the rear wheel locks after you make any change to the rear axles." It warns that if you fail to do so, "the wheel locks may not work." The same section says not to change the axle set-up unless you consult your health care provider first. Motion Composites' article lists more changes that call for a re-check: "If changes are made to wheel size, tire type, air pressure, wheel mounted power assist devices, or axle position, wheel lock function should be reassessed." Invacare's Tracer catalog lists wheel lock shoe spacer kits tied to rear wheel size; our [Invacare parts guide](https://www.mobilitatlas.com/blog/invacare-wheelchair-parts-guide.html) sets out its footnotes.

Solid tires do not lose pressure, but the Ki form allows grade aids only with pneumatic or pneumatic-with-airless-insert tires and the TiLite form says "Not available with solid rear tires", and Ki's form rules out its low profile scissor lock with full poly tires. In our view, if you change tire type, ask the dealer which locks the order form allows with the new tire.

## Replacing a wheel lock: the steps as the guides print them

Is a wheel lock a job you can do yourself? Some guides write the steps for users; others send the work to a technician. Here is what each one we read says.

1. Identify the lock: style (push or pull to lock, scissor), side, maker and any number on it, and the tube size under the clamp. Sportaid's Quickie push brake page asks buyers to "Please specify your chairs make & model & serial number."
2. Check the tires first: the Tracer SX5 manual says to inflate pneumatic tires before adjusting or replacing locks, and the Out-Front guides say to inflate the tires before adjusting.
3. Fit the clamp and lock loosely: Out-Front's guides say to slightly tighten one of the two Allen screws, slide the lock into the clamp, then set the position.
4. Set the depth your document prints, on a flat, level surface, in the lock position it names: the Tracer SX5 manual loosens and repositions with the lock open, then engages it to measure; the Drive manuals slide the clamp with the handle engaged; then tighten. Out-Front names a 3/16 inch Allen wrench, Ki a 5mm Allen wrench.
5. Test: Out-Front's guides say to "engage the wheel locks and push against the tires to verify that the wheel locks prevent the wheels from moving." The Tracer SX5 manual tests the occupied chair.
6. Repeat for the other side, then check legrests, extension handles and armrests for interference.

Who should do it. Ki's manual says: "Any maintenance check that you are not comfortable performing should be done by an authorized supplier." Its manual also says to use only Ki Mobility approved parts when replacing components. The Tracer SX5 manual says to contact a qualified technician if the locks do not hold. Out-Front adds a line for sport: "Out-Front recommends that you remove the wheel locks from your chair frame prior to engaging in any contact sport." In our view, a like-for-like push or pull lock on a clamp is a job a user or family member can do when the lock's guide prints the steps; a one-lever lock, a drum brake or a lock on a chair still under warranty is a job for the dealer.

In our view, keep the old lock until the new one holds, photograph the clamp before you loosen it, and keep the receipt.

## Part numbers by chair, as the makers print them

A part number belongs to the chair, the side, the style and the catalog heading it is printed under. These are the numbers we found, each with its document. We do not say a part fits any chair its page does not name.

| Chair or family | Part as printed | Document |
| --- | --- | --- |
| Tracer EX2, SX5, flip back arm (After 4/14/07) | 1101452 / 1101453 push R / L | Invacare catalog 02-016 |
| Tracer EX2, SX5, flip back arm (After 4/14/07) | 1101454 / 1101455 pull R / L | Invacare catalog 02-016 |
| Tracer EX2, SX5 (same table) | 1058899 extension, 6 in | Invacare catalog 02-016 |
| Guardian K1 | WCAA0065 wheel lock assembly, pair | Medline parts guide |
| Excel 2000 | WCA806990R lock, pair; WCA806907 tip | Medline parts guide |
| K4 Lightweight | WCA806990R lock, pair; WCA806907 tip | Medline parts guide |
| Quickie (Sportaid stock number) | 9078 push brakes, pair | Sportaid page |
| Quickie (Sportaid stock number) | 9077 scissor with clamp, pair | Sportaid page |
| Newton (Motion Composites) | 41056 left, 41057 right push | SpinLife pages |
| Newton Grade Aid | 9001582 left, 9001581 right | SpinLife record |
| TiLite ZR / ZRA, new chair | ZWLK3 Uni-Lock, ZWLK15 grade aids | TiLite order form |

Notes on the rows. The Invacare table is headed "Link-Pivot Style Wheel Locks Flip Back Arm - EX2, SX5 (After 4/14/07)"; the same page marks some single parts NLA (no longer available). The Medline guide's text runs its model columns together, so we tie each number only to the page heading it sits under. The Quickie numbers are Sportaid's stock numbers; the push brake page says the price "is for most standard Quickie wheelchairs" and that you will be contacted if your chair needs different brakes.

Drive's numbers are in our [Drive Medical parts guide](https://www.mobilitatlas.com/blog/drive-medical-wheelchair-parts-guide.html), and more Invacare numbers in our [Invacare parts guide](https://www.mobilitatlas.com/blog/invacare-wheelchair-parts-guide.html). In our view, read the number off the old lock or the catalog, not off a seller's title alone.

## What wheel locks cost at three US sellers

How much does a wheelchair brakes replacement cost? For a complete lock, pair or grade aid (two Quickie listings include a clamp), on the US seller pages we read, from $48.00 to $149.99 before any extra clamp, shipping or labor; the range leaves out a $996.00 one-handed system, brake pads, extension handles, mounts, grips and spare kits. Mobility Atlas read Sportaid's Brakes category and seven of its product pages, four SpinLife product pages and WheelchairBearings.com's wheel lock collection on 13 November 2026. Two things move the price more than the brand. The unit: Out-Front prices one side and the pair option adds $48 ($96.00 by our arithmetic), while Sportaid's Quickie push brakes are $85.00 a pair. The clamp: a pair of 1 inch clamps adds $82 and a pair of 1.25 inch clamps $101 on Out-Front's pages, so a pair of Out-Front push locks with 1 inch clamps comes to $178.00 by our arithmetic. Prices differ by country, seller, funding and sales period.

### Sportaid, Brakes category (all 8 tiles)

| Tile as printed | Price on tile | Unit, from the product page |
| --- | --- | --- |
| Out-Front Composite Pull to Lock Wheel Locks | $48.00 | One side; pair option adds $48 |
| Out-Front Composite Push to Lock Wheel Locks | $48.00 | One side; pair option adds $48 |
| Out-Front MBL Composite Scissor Wheel Locks | $78.25 | One side; pair adds $78.25 |
| MBL Performance Aluminum Scissor Lock | $79.00 | One side; pair adds $79 |
| Scissor Wheelchair Brakes with Clamp for Quickie | $81.50 | Priced per pair |
| Quickie Push to Lock Wheelchair Brakes | $85.00 | Price is per pair |
| Scissor Wheelchair Brakes with Clamp & Long Arm for Quickie | $100.00 | Price is per pair |
| Corima Absolute Brake – Composite Brake Pads | $23.50 | Not a wheel lock; left out of the range |

The category showed 8 results. Leaving out the Corima brake pads, the 7 wheel lock tiles ran from $48.00 to $100.00. On the product pages Sportaid prints two figures, labeled "Retail:" and "Cost:", and the tile shows the "Cost:" figure: for example "Retail: $65.00" and "Cost: $48.00" on each Out-Front push and pull page, and $120.00 and $85.00 on the Quickie push brakes page. The MBL scissor page prints only "Cost: $79.00". Sportaid's wheel lock search showed 61 results over four pages; on the first page of 16, five were wheel locks, all also in the category above, and the rest were chairs, wheels and rollators.

### SpinLife, product records

| Item as printed | Price | Struck price shown | Warranty field |
| --- | --- | --- | --- |
| Newton Grade Aid Wheelock (model 900) | $112.00 | $150.00 | Lifetime Limited Warranty |
| Newton Left Side Push Wheel Lock (41056) | $98 | $109 | Lifetime Limited Warranty |
| Newton Right Side Push Wheel Lock (41057) | $89 | $109 | Record not saved |
| Wheel Lock Extension, Each (PP-WLE) | Starting at $50.00 | None | No Warranty |
| Universal Wheel Lock Assembly (PP-RWLAC) | $55.00 | None | No Warranty |

The Newton prices are those on SpinLife's wheel lock listing, read on 12 November 2026, with the struck prices styled as such in the page markup; the records we saved on 13 November for the grade aid and the left lock store the same list prices, and the left lock's sale price as $98.1. The Newton locks are sold one side each, so a left and a right together came to $187 by our arithmetic from the listing's displayed prices ($98 and $89). The ProActive extension's 8 inch option adds $5, to $55.00. The "Lifetime Limited Warranty" label is SpinLife's field name; the warranty text under it is Motion Composites' and, as the warranty section shows, gives components one year.

### WheelchairBearings.com, wheel lock collection (all 15 tiles)

The collection showed 15 tiles. Five are complete locks sold as pairs: three colors of Reckless Wheelchairs' micro adjustable aluminum scissor brakes at $144.99 each (original price $174.99), RWC push to lock lever brakes at $100.00, and a tile titled Reckless Wheelchairs all aluminum push-to-lock lever brakes (brand line "Top Gear") at $149.99 (original price $159.99). Over those five, the range was $100.00 to $149.99. The other ten tiles are extensions ($39.99 generic, $84.99 TiLite), brake mounts ($39.99), wheel lock grips ($19.99), spare kits and slider nuts ($9.99 to $19.99) and the Push Lox system ($996.00), which we leave out of the lock range.

Can't find your lock? Mobility Atlas can find and quote wheel locks, clamps, shoes, extension handles, grade aids and attendant brake parts, including parts that are not listed on the site. Send an enquiry or part request through our [wheelchair parts and accessories page](https://www.mobilitatlas.com/c/wheelchair-parts-accessories.html) with the chair's make, model and serial number, the lock style and side, the frame tube size and a photo; you receive a written quote with delivery to your country, and nothing is charged before you accept it.

## Wheel lock options on a new chair: the order forms

If you are ordering a new chair, the wheel lock is chosen on the order form, and the price of each option is printed there. These are the US prices on the two forms we read; they are option prices on a new chair, not prices for spare parts.

| Option as printed | Ki Rogue 2 (effective 8/17/2026) | TiLite ZR / ZRA (March 2026) |
| --- | --- | --- |
| Push to lock | N/C | No charge (composite) |
| Pull to lock | N/C | No charge (composite) |
| Push to lock, flush mount | N/C | Not listed |
| Under seat or low profile scissor | $37 / $68 | $158.00 / $175 (MBL) |
| Uni-Lock | Not listed | $179.00 |
| Extension handles (E0961) | $88 | $93.00 |
| Grade aids (E0974) | $157 | $190.00 |
| Omit wheel locks | N/C | Not listed |

The TiLite form says its composite push and pull locks are available only within a range of rear wheel spacing, printed on the form. Both forms carry HCPCS codes next to some options, and both say what those codes mean. Ki's form says: "Proper use of HCPCS Codes does not ensure coverage or payment." TiLite's says: "HCPCS Codes are for reference purposes only." In our reading, a code on an order form is the maker's coding, not a promise that any payer will cover the option. By our arithmetic the TiLite grade aids cost $33 more than Ki's on these forms, and its extension handles $5 more.

Omitting locks is an option on the Ki form. Motion Composites' article says some highly skilled users skip them, and warns: "Omitting wheel locks is not a suitable option for everyone and comes with significant safety risks." In our view, that is a decision for you and your seating clinician.

## Warranty and returns: document by document

A wheel lock's warranty depends on who made it and where you bought it. Each line below belongs to the one document that prints it.

- Ki Mobility Rogue 2 manual: "All other Ki Mobility-made parts and components of this wheelchair are warranted against defects in materials and workmanship for one year from the date of first consumer purchase." It says the warranty "applies in North America only" and that you must "Pay any charges for labor to repair or install parts."
- Quickie Nitrum manual: "We warrant all Sunrise-made parts and components of this wheelchair against defects in materials and workmanship for one year" from the first consumer purchase.
- Invacare Tracer SX5 manual: side frames and cross members five years; "remaining components" thirteen months; "This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product." It is "not transferable or assignable to any subsequent purchaser or owner."
- Medline Guardian user guide: it says it covers the frame for the life of the chair, and "the parts and upholstery on the wheelchair to be free from defect in materials and workmanship for a period of one (1) year from date of purchase by the original purchaser."
- Drive Silver Sport 2 manual: a limited three year warranty for the original consumer purchaser, which "does not extend to non-durable components, such as rubber accessories, casters, and grips".
- Motion Composites, as SpinLife's Newton record page prints it: "Components: One year", extended "only to the original consumer purchasers".

Seller terms are separate. SpinLife's records list "No Warranty" for both ProActive items, a 20% restocking fee on those and a 15% fee on the two Newton records we saved, and say "An RA (Return Authorization) from SpinLife must be requested within 30 days of delivery." Sportaid's Out-Front push lock page says that for orders outside the US it emails the exact shipping cost; it creates a preauthorization but does not charge the card until you approve the shipping costs; we did not save Sportaid's returns page, so we say nothing about its return terms.

What this means in practice, in our reading: a wheel lock that fails on a chair still inside the maker's component warranty is a warranty claim through the dealer, and fitting a non-original part can matter. The Tracer SX5 manual's exclusions include products modified "through the use of unauthorized parts or attachments", and Ki's manual says to use only Ki Mobility approved parts. Ask the dealer before you fit a generic lock to a chair under warranty.

## Medicare, codes and funding

In the US, wheel locks have their own billing codes. The National Library of Medicine's HCPCS lookup lists E2206, "Manual wheelchair accessory, wheel lock assembly, complete, replacement only, each"; E0961, "Manual wheelchair accessory, wheel lock brake extension (handle), each"; E2228, "Manual wheelchair accessory, wheel braking system and lock, complete, each"; and E0974, "Manual wheelchair accessory, anti-rollback device, each".

Medicare's rule for wheelchair accessories, LCD L33792 (the version in effect when we read it on 9 November 2026, revision effective 10/01/2025, ending 12/19/2026), says: "Options and accessories for wheelchairs are covered if the beneficiary has a wheelchair that meets Medicare coverage criteria and the option/accessory itself is medically necessary." For grade aids it says: "Anti-rollback device (E0974) is covered if the beneficiary self-propels and needs the device because of ramps." A new version is listed as future effective on 12/20/2026; the parts of it we saved do not include the anti-rollback line, so we cannot say whether that line changes.

The policy article A52504 bundles wheel locks with a new chair. Its table lists E2206 in Column II for manual wheelchair bases, and the article says: "Codes listed in Column II are not separately payable from the wheelchair base and must not be billed separately at the time of initial purchase or rental of the wheelchair." In our reading, that makes E2206 a code for replacement on a chair you already have, as its name says.

For repairs, Medicare's booklet says that if you own Medicare-covered equipment Medicare may also cover repairs, but "the supplier who sold it to you isn't required to repair it", and Medicare.gov says you pay 20% of the Medicare-approved amount after the Part B deductible, if your supplier accepts assignment; our [wheelchair parts guide](https://www.mobilitatlas.com/blog/wheelchair-parts-guide.html) covers Medicare repair rules in full. Medicare Advantage, Medicaid, the VA and private plans set their own rules; we did not read their rules, so ask the plan in writing. Funding rules outside the US differ again.

## What FDA reports and recalls show about wheel locks

We ran an openFDA word search of device reports on 13 November 2026 for "wheel lock", "wheel locks", wheellock or wheellocks in the report text, limited to product code IOR, which FDA's classification record names "Wheelchair, Mechanical". The database, last updated 4 November 2026, returned 1,780 reports received from 1996 to 29 October 2026. These are reports, not failures counted across all chairs, and nothing here is a rate. The FDA's page on the database says this "passive surveillance system has limitations", including "under-reporting of events", and that the data are not intended to evaluate rates of adverse events. The page lists voluntary reports alongside reports from manufacturers, distributors and user facilities; the grade aid report above is a manufacturer report.

The counts are lumpy. 1,215 of the reports were received in 2013 to 2016, and 156 in 2026 so far. Of the 2026 reports, 155 name Medline as the maker, under six spellings of its name, and 1 names Ki Mobility. FDA's page says MDR data are "not intended to be used either to evaluate rates of adverse events, evaluate a change in event rates over time", so we read nothing into the yearly pattern. We did not read the narratives of these reports one by one; our [manual wheelchair repair guide](https://www.mobilitatlas.com/blog/manual-wheelchair-repair-guide.html) read and coded a large set of manual wheelchair reports, wheel locks included, and found loosening to be the most common wheel lock problem in them.

Recalls. A word search of FDA recall records for "wheel lock", "wheel locks" or wheellock (last updated 12 November 2026) returned three records, none for a wheelchair: a Siemens ultrasound system, recalled in part because the part that engages its wheel lock could disconnect, and a transport rollator and a four-wheel walker, both recalled because a caster could detach. The search of wheelchair recalls for brake or lock returned the one Invacare Solara 3G hub brake recall described above. In our view, to check your own chair, search the FDA recall database by maker and model, and ask the maker with the serial number.

## Three traps when you replace wheelchair brakes

Trap one: buying the right lock with the wrong clamp. A lock sold "No Clamp" needs a clamp that fits your tube, and Out-Front's scissor page prints one tube range in its text and different clamp sizes in its options. In our view, measure the tube and read the clamp option, not the headline.

Trap two: adjusting on a soft tire. The Out-Front guides say that if you adjust the locks when the tires are under-inflated, "the lock will not operate properly when the tire is fully inflated." In our view, inflate to the sidewall figure first, then set the depth your documents print, then test.

Trap three: treating a pair price and a side price as the same thing. Out-Front and Newton price one side; the Quickie and Reckless listings we read price a pair. By our arithmetic, a $48.00 lock makes a $96.00 pair before clamps. In our view, check the unit on the product page before comparing.

## Three composite scenarios

These are composite scenarios, not individual customers. Each uses only the documents for that chair.

Scenario one: a Tracer SX5 with flip back arms, built after 4/14/07, and pneumatic tires. The left lock slips during transfers. The owner checks the tire against the sidewall pressure, as the Tracer SX5 manual says to before adjusting. The lock still slips, so they loosen the bolt and locknut and reset it until the shoe embeds 3/16 inch, the figure the manual prints for pneumatic tires, then test the occupied chair. It still moves, so they follow the manual's line to contact a qualified technician. Invacare's catalog lists the push-to-lock left assembly as 1101453 under the flip back arm heading for chairs after 4/14/07; the manual's warranty gives remaining components thirteen months and covers no labor.

Scenario two: a new TiLite ZR for someone who lives at the top of a ramp. The order form lists grade aids (ZWLK15, $190.00) as push to lock and not available with solid rear tires, so the order keeps pneumatic tires. The form prices extension handles for the composite locks at $93.00. The therapist and the user try both before the form is signed, and the dealer notes that the form's HCPCS codes are "for reference purposes only".

Scenario three: a Ki Rogue 2 user who uses extension handles. The Rogue 2 manual says extension handles "should be removed during transfer to ensure wheel locks are not deactivated", so the user takes them off before each transfer. After new tires, the manual's maintenance table says tire wear and pressure changes "will require the wheel locks to be adjusted", so they reset each clamp with a 5mm Allen wrench and test on a flat level surface. Ki's warranty covers parts for one year but not labor.

## What to ask the dealer, seller or therapist

- Ask the seller: is this price for one side or a pair, and is a clamp included?
- Ask the seller: which tube diameter does the clamp fit, and do you have an offset or extended clamp if my wheels are set wide?
- Ask the dealer: what depth into the tire does the maker of my chair specify for my tire type?
- Ask the dealer: is my chair still under the maker's component warranty, and will a non-original lock affect it?
- Ask the therapist: push, pull or scissor, given how I transfer and which hand I use?
- Ask the therapist: would an extension handle, a one-lever lock or a grade aid help, and do I also need anti-tippers?
- Ask the attendant brake or drum brake maker's dealer: who adjusts the cables, and how often does the manual say to check them?

In our view, keep the answers in writing.

## Sources and documents

Maker documents, read 13 November 2026: Invacare Tracer SX5 user manual, Part No. 1110550 (wheel lock pages); Ki Mobility Rogue 2 and Rogue XP manual (cover dated 2025-02-13) and Rogue 2 order form DCN1017.14; Permobil TiLite ZR and ZRA order form, March 2026; Out-Front installation and user guides for composite push-to-lock and pull-to-lock wheel locks (hosted by Sportaid); Motion Composites' unilateral wheel lock installation sheet and its article on wheel lock types. Read 12 November 2026: Invacare parts catalog Form No. 02-016, wheel lock page; Drive's Wheel Lock Extensions page; Medline's parts guide. Read 9 November 2026: Quickie Nitrum manual, Medline Guardian user guide, Drive Silver Sport 2 and Viper Plus GT manuals, Karman LT-1000 documents, other pages of the Tracer SX5 manual.

Sellers: Sportaid (Brakes category, seven product pages and the first search page) and WheelchairBearings.com, read 13 November 2026; SpinLife's wheel lock listing, read 12 November 2026, and four SpinLife product records, read 13 November 2026. Government: CMS LCD L33792 (current and future versions) and policy article A52504, Medicare's equipment booklet and Medicare.gov's wheelchair page, and FDA's page on its report database, read 9 November 2026; the National Library of Medicine's HCPCS lookup and openFDA device reports and recalls, read 13 November 2026. Two sellers could not be read: one showed a bot check that we did not try to get around, and one search page returned not found.

Method in brief: how we checked. We copied each page or PDF as text on the dates above and took every figure, quote, part number and price from those copies; quotes and numbers are checked by script against the saved texts. Prices are as printed, with the label the page used, and every range names the tiles it covers and the ones it leaves out. Related guides: [wheelchair parts](https://www.mobilitatlas.com/blog/wheelchair-parts-guide.html), [manual wheelchair repair](https://www.mobilitatlas.com/blog/manual-wheelchair-repair-guide.html), [tire and caster care](https://www.mobilitatlas.com/blog/tire-caster-care.html).

## Common questions

### Are wheelchair wheel locks the same as brakes?

No. Wheel locks keep a stopped chair from rolling; they are not designed to slow a moving one. The Invacare Tracer SX5 manual says: "Wheel locks are not brakes." Parts that do slow a chair are attendant hand brakes on transport chairs, such as Karman's loop brakes, and drum brakes on chairs that offer them, such as the drum brakes the Rogue 2 manual describes.

### How do I know which replacement wheel lock fits my wheelchair?

Match four things to the old lock: the style (push to lock, pull to lock or scissor), the side, the maker's part number if the chair's parts catalog prints one, and the outside diameter of the frame tube under the clamp. Seller pages list clamps for 1 inch or 1.25 inch tubing. Give the seller your chair's make, model and serial number; Sportaid's Quickie push brake page asks for them and says the order "cannot be processed without model of chair."

### How tight should a wheelchair wheel lock be against the tire?

The manuals measure depth into the tire, not tightness. The Medline Guardian, Drive Silver Sport 2, Drive Viper Plus GT and Quickie Nitrum manuals say at least 1/8 inch; the Invacare Tracer SX5 manual says at least 1/8 inch (3/16 inch for pneumatic tires); Out-Front's guides say at least 3/16 inch. Inflate the tire to the sidewall figure first, then lock the chair and push it to test. If it still moves, the Tracer SX5 manual says to contact a qualified technician.

### What is a wheelchair brake extension and do I need one?

It is a longer handle that slips over the wheel lock lever so the lock is easier to reach and needs less force. Whether you need one depends on your reach and grip, which is a question for your therapist. The Ki Mobility manual says extension handles should be removed during transfer to ensure wheel locks are not deactivated, and the Invacare manual says to remove them before swinging elevating legrests aside on chairs with push-to-lock locks.

### Does Medicare pay for replacement wheelchair brakes?

Medicare has codes for them: E2206 for a complete replacement wheel lock assembly, E0961 for an extension handle and E0974 for an anti-rollback device. LCD L33792 (the version in effect on 9 November 2026) covers accessories if the chair meets Medicare criteria and the accessory is medically necessary, and covers E0974 if the user self-propels and needs it because of ramps. Medicare Advantage, Medicaid, the VA and private plans set their own rules; we did not read their rules, so ask them in writing. Prices and funding also differ by country, seller and sales period.

### Can Mobility Atlas quote a wheel lock that is not listed on the site?

Yes. Mobility Atlas can find and quote wheel locks, clamps, shoes, extension handles and grade aids, including parts that are not listed. Send an enquiry or part request with the chair's make, model and serial number, the lock style and side, the frame tube size and a photo; you receive a written quote with delivery to your country, and nothing is charged before you accept it.

## Sources

- Invacare: Tracer SX5 wheelchair user manual, Part No. 1110550 (PDF; wheel lock pages read 13 November 2026, warranty and safety pages read 9 November 2026): https://status.invacareamerica.com/1110550.pdf
- Invacare: Parts catalog Form No. 02-016, Tracer EX2, SX5, link-pivot wheel lock page (PDF, read 12 November 2026): https://status.invacareamerica.com/parts/02_016.pdf
- Ki Mobility: Rogue 2 and Rogue XP user instruction manual and warranty (PDF): https://www2.kimobility.com/OwnersManuals/English-Spanish/Rogue2_XP-Eng-Spa.pdf
- Ki Mobility: Rogue2 order form, USA, DCN1017.14, effective 8/17/2026 (PDF): https://www2.kimobility.com/OrderForms/USA/Rogue2.pdf
- Permobil: TiLite ZR / ZRA order form, US, March 2026 (PDF): https://permobilwebcdn.azureedge.net/media/ffdharrj/us_tilite-zr-zra-2026_03-2.pdf
- Sunrise Medical: Quickie Nitrum owner's manual (PDF, read 9 November 2026): https://www.sunrisemedical.com/getattachment/3362e72c-a8af-47b8-ab99-320159fdd501/.aspx
- Medline: Standard manual wheelchairs user guide, Guardian K1 to K4 (PDF hosted by Vitality Medical, read 9 November 2026): https://www.vitalitymedical.com/pdf/assets-1/guardian-k1-manual.pdf
- Medline: Transport chair, wheelchair and homecare bed parts guide (PDF hosted by Vitality Medical, read 12 November 2026): https://www.vitalitymedical.com/pdf/assets-2/brochure-replacement-parts-guide-medline-wheelchairs.pdf
- Drive Medical: Silver Sport 2 wheelchair page and owner's manual (read 9 November 2026): https://shop.drivemedical.com/us/en/products/mobility/wheelchairs/standard-wheelchairs/silver-sport-2-wheelchair/p/969-1
- Drive Medical: Viper Plus GT owner's manual (PDF, read 9 November 2026): https://shop.drivemedical.com/medias/1157-1?context=bWFzdGVyfGltYWdlc3wyNTEyMDd8YXBwbGljYXRpb24vcGRmfGFHSXdMMmc1WVM4eE1qWXlPREl5TkRNME5EQTVOQzh4TVRVM0xURXxhOTlmODIxMzk1NThkNWQzNTgxOGRjYTE3ZjMyYTAwNDZlZGY1ODQ2MDdjYzFkYjMwMWUzM2YyZWJhMTZlNGJj
- Drive Medical: Wheel Lock Extensions page (read 12 November 2026): https://shop.drivemedical.com/us/en/products/mobility/wheelchairs/accessories/wheel-lock-extensions/p/1234-1
- Karman Healthcare: LT-1000 transport wheelchair page, LT-1000HB sheet and user guide (read 9 November 2026): https://www.karmanhealthcare.com/product/lt-1000-transport-wheelchair/
- Out-Front: Compact Composite Push to Lock Wheel Locks, installation and user guide (PDF hosted by Sportaid): https://sportaid.com/wp-content/uploads/migrated_files/19808/19808_1473260746_OF-3RLOCKPL_installation.pdf
- Out-Front: Compact Composite Pull to Lock Wheel Locks, installation and user guide (PDF hosted by Sportaid): https://sportaid.com/wp-content/uploads/migrated_files/19809/19809_1473264173_OF-3RLOCKPL_installation.pdf
- Motion Composites: Unilateral wheel lock installation/replacement, MC-MKTG-WI-0026 (PDF): https://www.motioncomposites.com/media/How_to/New-tech-docs/MC-MKTG-WI-0026-unilateral-wheel-lock-installation.pdf
- Motion Composites: Wheel locks: Unlocking Safety and Function (published 15 September 2020): https://www.motioncomposites.com/en_us/community/blog/tips-and-tricks/wheel-locks-unlocking-safety-and-function
- Sportaid: Brakes category, wheelchair parts (prices read 13 November 2026): https://sportaid.com/product-category/wheelchair-wheels-tires-tubes-parts/wheelchair-parts-stuff/brakes-wheelchair-parts-stuff/
- Sportaid: Search results for wheel lock, page 1 of 4: https://sportaid.com/search/wheel%20lock
- Sportaid: Out-Front Composite Push to Lock Wheel Locks: https://sportaid.com/product/out-front-composite-push-to-lock-wheel-locks/
- Sportaid: Out-Front Composite Pull to Lock Wheel Locks: https://sportaid.com/product/out-front-composite-pull-to-lock-wheel-locks/
- Sportaid: Out-Front MBL Composite Scissor Wheel Locks: https://sportaid.com/product/out-front-mbl-composite-scissor-wheel-locks/
- Sportaid: MBL Performance Aluminum Scissor Lock: https://sportaid.com/product/mbl-performance-aluminum-scissor-lock/
- Sportaid: Quickie Push to Lock Wheelchair Brakes: https://sportaid.com/product/quickie-push-brakes-without-clamp-p2/
- Sportaid: Scissor Wheelchair Brakes with Clamp for Quickie: https://sportaid.com/product/scissor-brakes-with-clamp-for-quickie/
- Sportaid: Scissor Wheelchair Brakes with Clamp and Long Arm for Quickie: https://sportaid.com/product/scissor-brakes-with-clamp-for-invacare-top-end-p7/
- SpinLife: Wheel Locks listing (read 12 November 2026): https://www.spinlife.com/parts/manual-wheelchair-parts/wheel-locks/critpath/match.cfm?categoryID=721
- SpinLife: Motion Composites Newton Grade Aid Wheelock: https://www.spinlife.com/Motion-Composites-Newton-Grade-Aid-Wheelock-Wheel-Locks/spec.cfm?productID=120246
- SpinLife: Motion Composites Newton Left Side Push Wheel Lock: https://www.spinlife.com/Motion-Composites-Newton-Left-Side-Push-Wheel-Lock-Wheel-Locks/spec.cfm?productID=120245
- SpinLife: Proactive Medical Wheel Lock Extension, Each: https://www.spinlife.com/Proactive-Medical-Wheel-Lock-Extension,-Each-Wheel-Locks/spec.cfm?productID=181551
- SpinLife: Proactive Medical Universal Wheel Lock Assembly: https://www.spinlife.com/Proactive-Medical-Universal-Wheel-Lock-Assembly-Wheel-Locks/spec.cfm?productID=181552
- WheelchairBearings.com: Wheelchair Wheel Locks collection (prices read 13 November 2026): https://wheelchairbearings.com/collections/wheelchair-wheel-locks
- WheelchairBearings.com: PUSH LOX One-Handed Wheelchair Locking System (read 13 November 2026): https://wheelchairbearings.com/products/push-lox-one-handed-wheelchair-locking-system
- WheelchairBearings.com: TiLite Wheelchair Wheel Lock Extensions with Lanyard (Pair) (read 13 November 2026): https://wheelchairbearings.com/products/tilite-wheel-lock-extensions-with-lanyard-pair
- openFDA: device classification, product code IOR: https://api.fda.gov/device/classification.json?search=product_code:IOR
- National Library of Medicine: HCPCS lookup, wheel lock (E0961, E2206, E2228): https://clinicaltables.nlm.nih.gov/api/hcpcs/v3/search?terms=wheel%20lock&df=code,display,long_desc&maxList=20
- National Library of Medicine: HCPCS lookup, E0974: https://clinicaltables.nlm.nih.gov/api/hcpcs/v3/search?terms=E0974&df=code,display,long_desc&maxList=20
- CMS: LCD L33792, Wheelchair Options/Accessories, version 43 (read 9 November 2026): https://www.cms.gov/medicare-coverage-database/view/lcd.aspx?lcdid=33792&ver=43
- CMS: LCD L33792, future version effective 12/20/2026 (read 9 November 2026): https://www.cms.gov/medicare-coverage-database/view/lcd.aspx?lcdid=33792
- CMS: Article A52504, Wheelchair Options/Accessories policy article, version 61 (read 9 November 2026): https://www.cms.gov/medicare-coverage-database/view/article.aspx?articleid=52504&ver=61
- Medicare: Medicare Coverage of Durable Medical Equipment and Other Devices, booklet 11045 (read 9 November 2026): https://www.medicare.gov/publications/11045-medicare-coverage-of-dme-and-other-devices.pdf
- Medicare.gov: Wheelchairs and scooters coverage page (read 9 November 2026): https://www.medicare.gov/coverage/wheelchairs-scooters
- openFDA: device reports, product code IOR, word search for wheel lock, counts by date received: https://api.fda.gov/device/event.json?search=device.device_report_product_code:IOR+AND+mdr_text.text:(%22wheel+lock%22+OR+%22wheel+locks%22+OR+wheellock+OR+wheellocks)&count=date_received
- openFDA: device reports, same search, received in 2026, counts by maker: https://api.fda.gov/device/event.json?search=device.device_report_product_code:IOR+AND+mdr_text.text:(%22wheel+lock%22+OR+%22wheel+locks%22+OR+wheellock+OR+wheellocks)+AND+date_received:[20260101+TO+20261231]&count=device.manufacturer_d_name.exact
- openFDA: device reports, product code IOR, word search for grade aid, hill holder and anti-rollback: https://api.fda.gov/device/event.json?search=device.device_report_product_code:IOR+AND+mdr_text.text:(%22grade+aid%22+OR+%22grade+aids%22+OR+%22hill+holder%22+OR+%22hill+holders%22+OR+%22anti-rollback%22+OR+%22anti+rollback%22)&limit=100
- openFDA: device recalls, product code IOR, word search for brake or lock: https://api.fda.gov/device/recall.json?search=product_code:IOR+AND+(reason_for_recall:(brake+OR+brakes+OR+lock+OR+locks)+OR+product_description:(brake+OR+brakes))&limit=100
- openFDA: device recalls, word search for wheel lock: https://api.fda.gov/device/recall.json?search=product_description:(%22wheel+lock%22+OR+%22wheel+locks%22+OR+%22wheellock%22)+OR+reason_for_recall:(%22wheel+lock%22+OR+%22wheel+locks%22+OR+%22wheellock%22)&limit=100
- FDA: About the MAUDE database (read 9 November 2026): https://www.fda.gov/medical-devices/mandatory-reporting-requirements-manufacturers-importers-and-device-user-facilities/about-manufacturer-and-user-facility-device-experience-maude-database

Read on 13 November 2026. The wording of the article is our own.

## About the author

Mobility Atlas is run by Anna, who has used a wheelchair for 19 years, since she was ten. She started it because she always wanted one place where a person who needs a chair, a wheel, a cushion or a spare part can see everything that is made, side by side, and simply ask for it. She reads and answers every enquiry herself.

Contact: anna@mobilitatlas.com, WhatsApp +66 65 398 9085. Canonical facts about Mobility Atlas: https://www.mobilitatlas.com/about/facts.html
