Ki Mobility parts in 2026: Ki wheelchair parts for the Catalyst 5, Rogue2 and Rogue XP, Focus CR, Liberty and Little Wave, part numbers, retail prices and warranty
Ki Mobility parts: how Ki sells them, Ki Parts page by page, Catalyst 5 parts and Ki Mobility Rogue parts, retail prices from Ki's own list, warranty and recalls.
Contents
- The short answer
- How we compared, and our interest
- The Ki chairs this guide covers
- How Ki sells parts: dealers, Ki Parts and the retail price list
- Reading a Ki part number and the notes above each table
- Wheel locks: Catalyst 5 and Rogue2 share the thru-post locks
- Other Ki wheel locks: Hemi, Focus CR, Liberty and Little Wave
- What the manuals let an owner do with wheel locks
- Casters, forks and caster bearings
- Quick-release axles and axle plates
- Rear tires, tubes and wheels
- Anti-tips: four systems, different numbers
- Footrests, hangers and footplates
- Armrests and side guards
- Backs, push handles and upholstery
- What the manuals let an owner adjust
- What Ki parts cost on Ki's US retail list
- Pair or two singles: what the arithmetic shows
- What seller pages show for Ki parts
- Warranty on Ki parts: what the two manuals print
- Recall records for Ki chairs
- Medicare and other funders
- Ordering Ki parts through Mobility Atlas
- Three traps
- Three composite scenarios
- Questions to ask before you order a Ki part
- Sources and documents
- Common questions
- Sources
The short answer
Ki Mobility parts come from Ki Mobility, the Stevens Point, Wisconsin maker of the Catalyst, Rogue, Focus CR, Liberty and Little Wave wheelchairs, but Ki sends riders to a dealer for them. Its Contact page says: "For service or repair parts for your personal device, please click here to find a dealer near you."
What Ki does publish is an online parts manual called Ki Parts, with a part-number table on each assembly page for each chair, and a US retail parts price list of 1,532 pages headed "US Ki Retail Parts Pricing"
, marked "Effective 04/01/2026". This guide reads both for the Catalyst 5 and the Rogue2, the two Ki chairs we went deepest on, and for the wheel locks and anti-tips of the Catalyst 5Vx, Rogue XP, Focus CR, Liberty and three Little Wave chairs (anti-tips only for the Little Wave XP).
How do you buy Ki Mobility wheelchair parts? Start with the model, the serial number and, if you have it, the invoice date, because Ki's parts manual splits some parts by when the chair was invoiced or by serial number. Mobility Atlas read Ki Parts for nine Ki chairs, Ki's US retail price list, the Catalyst 5 and Rogue 2 / Rogue XP owner's manuals, two seller sites and FDA recall records on 13 November 2026. On those pages a Ki part has a six-digit number, such as 124094 for a right push-to-lock thru-post wheel lock that Ki lists under both the Catalyst 5 and the Rogue2, at $43.29 on the April 2026 retail list. In our view, write down the model, serial number and part number, photograph the old part, and ask the dealer for a written price with fitting.
Two things set Ki apart from the Sunrise Medical catalog we read for our Quickie parts guide. Ki's price list names its column "Retail (USD)", so the figures in this guide are Ki's own published retail prices, not an unlabeled column. And Ki's parts pages show no prices at all to a visitor who is not logged in; the prices come only from the separate PDF. A dealer may charge more or less than the retail list, and fitting, shipping and tax come on top.
Setup is not a parts decision. Where the rear axle sits, how the footrests and anti-tips are set and which back a rider uses change balance and posture, and the Catalyst 5 manual says "Wheelchair set up should be done only by an authorized technician."
Which setup suits a rider is for their physical therapist, occupational therapist or seating clinician to decide; this guide explains the parts and what to ask, and then stops.
How we compared, and our interest
Mobility Atlas earns a fee or margin when you order through us; the comparison below uses only Ki Mobility's published parts manual, price list, manuals and web pages, US seller pages, public FDA records and, where named, rows of our own catalog. We did not buy, fit or test any Ki part, and we did not ask Ki or any seller a question.
Our method was simple. On 13 November 2026 we opened each page named below in a browser and saved its text, with the address and the date, before writing. For Ki Parts we listed the assembly pages under nine chairs (1,871 assembly pages in all) and saved 76 of them in full: the notes Ki prints above each table and every row of the table (item, part number, description, quantity). For the price list, a PDF of 1,532 pages, we extracted the text in the browser, rebuilt its 53,611 rows and then looked up, by exact part number, the 148 numbers this guide uses; every price below is the row printed for that number. For the Catalyst 5 manual we saved the English pages in full. Four extracts of the Rogue 2 / Rogue XP manual that our team saved on 13 November 2026 for earlier guides cover its wheel locks, footrests, armrests, anti-tips, maintenance and warranty, and we quote from those. Where we did arithmetic, such as two single locks against a pair, a script computed it from the saved text.
A part number belongs to the model, assembly page and row it is printed under. When the same number is listed under two chairs, we say so and name both pages; we never say a part fits a chair whose page does not list it. The price list names parts, not chairs, so a description such as "Wheellock Clamp CAT" is Ki's wording, not our fitment claim. Prices checked November 2026. Documents checked November 2026.
The Ki chairs this guide covers
Ki Parts opens with a Categories menu; under Search By Wheelchair it splits chairs into Rigid, Folding and Tilt-In-Space, and on 13 November 2026 those three held 23 model folders, from the Rogue2 and Catalyst 5 to discontinued chairs such as the "Tsunami Ti (Discontinued)"
. We listed every assembly page under the nine chairs in the table. The counts are pages, not parts; one page can hold more than a hundred rows.
| Chair (Ki Parts folder) | Assembly pages listed | Pages we saved in full | Owner's manual read |
|---|---|---|---|
| Catalyst 5 (Folding) | 303 | 34 | Yes, English pages |
| Catalyst 5Vx (Folding) | 265 | 3 | No |
| Rogue2 (Rigid) | 176 | 26 | Yes, extracts (Rogue 2 / Rogue XP manual) |
| Rogue XP (Rigid) | 221 | 3 | Same manual as Rogue2 |
| Focus CR (Tilt-In-Space) | 218 | 2 | No |
| Liberty (Tilt-In-Space) | 154 | 2 | No |
| Little Wave XP (Rigid) | 185 | 2 | No |
| Little Wave Clik (Rigid) | 178 | 2 | No |
| Little Wave Flip (Tilt-In-Space) | 171 | 2 | No |
Older parts stay in Ki Parts. Of the 1,871 assembly pages listed under the nine chairs, 266 carry the word discontinued in their name or folder, from 9 under the Liberty to 55 under the Rogue XP; the Catalyst 5 has 39, such as "(Discontinued) Catalyst 5 Standard Axle Plate" and a folder of discontinued wheel locks. In our reading, a page marked discontinued shows what was fitted to older chairs; whether a part on it can still be supplied is a question for the dealer. Rows on current pages that name the number they replace, covered below, show how Ki carries some numbers forward.
For the Catalyst 5 and the Rogue2 we saved the pages for wheel locks, casters and forks, anti-tips, axles, tires (and, for the Catalyst 5, tubes), footplates and hangers or footrests, armrests, side guards and push handles. For the other seven chairs we saved only their wheel lock and anti-tip pages (anti-tip pages only for the Little Wave XP), so for them this guide says less. We did not read back upholstery pages for any chair. What each chair is, what it costs new and how Ki's warranty reads across all seven manuals are in our Ki Mobility guide; this page stays on parts.
How Ki sells parts: dealers, Ki Parts and the retail price list
Ki's own documents describe a dealer route. Besides the Contact page line quoted above, the maintenance section of the Catalyst 5 manual says: "Only use Ki Mobility approved parts when replacing components."
It then says to contact your authorized service representative, with a pointer to the dealer locator on Ki's website, "for parts information, identification, ordering and additional technical information or instruction"
, and that most components "are illustrated in" Ki Parts on Ki's website. The Rogue 2 / Rogue XP manual prints the same lines.
Ki Parts sits on Ki Online, a site whose menu shows New Quote and Log In links. Its Support menu links three price lists: "Retail Price List - US", "Retail Price List - Canada"
and "Retail Price List - AADL". When we opened the parts manual without logging in, each assembly page showed the notes and a table with the columns Item #, Part #, Description and Qty., and no price. We did not log in, add anything to the cart or start a quote.
The US price list is a separate PDF. Its pages are headed "US Ki Retail Parts Pricing"
, carry three columns (Part Number, Description, Retail (USD)) and print "Effective 04/01/2026". The list is sorted by part number, not by chair, and runs to 53,611 rows by our extraction, including screws and other fasteners as well as wheels and locks. A description sometimes carries a model tag, such as "CAT" or "Tilt", and sometimes does not; in the 342 rows whose description contains "wheel lock", 27 name the Catalyst (CAT, Cat or Catalyst) and 32 name Tilt or Focus. In our reading, the price list tells you what a numbered part costs, and only the parts manual tells you which chair it belongs to.
Who fits the part is a separate question from who sells it. Ki's Warranty page says "Warranties are found within the User Instruction Manuals"
, and both manuals we read make warranty claims go through an authorized supplier, covered in the warranty section below. The general steps for any brand, from the label to the part group, are in our wheelchair parts guide, and the power chair maker's route is in our Permobil parts guide; the sections below apply them to Ki.
Reading a Ki part number and the notes above each table
On the pages we saved, part numbers are six digits, such as 124094 or 000143, some with a suffix (INST or a color code). Several patterns on the pages we saved change what you order:
- Side and pair. Many parts come as a right, a left and a PAIR number. On the Catalyst 5 page, Ki's thru-post push lock is 124094 (right), 124095 (left) and 124896 (PAIR); the description, not the number, tells you which.
- Color suffix. Some rows end in underscores, such as 500509_ _ _, which the fork page calls a
"Color Anodized/Color Accent Fork Assembly"
. In our reading the blanks stand for a color code that the plain number (500509, black) does not carry; ask the dealer which code your chair has. - Instruction kits. Some numbers end in INST, such as 003225INST, which the hanger page calls
"Assembled 4-Way In Line Hanger Release with Instruction"
, next to 003225 without the instruction. - Replacements. Some rows name the number they replace: the row for 100807, a 5 inch soft roll caster, says
"Replaced part number 100518"
. An old invoice may show the old number. - Date and serial notes. Some pages split parts by invoice date or serial number, quoted below where they matter.
The notes above a table matter as much as the rows. The Catalyst 5 page "Catalyst Push and Pull to Lock"
opens with "If invoiced prior to 7/2025 pair of wheel lock will be needed"
, "Implemented August 2022" and "Notice: Chair configuration review required prior to parts being quoted or ordered"
, and tells the reader to check a reference sheet to decide between standard and reversed locks. The Rogue2 / Rogue XP fork page says it was "Used on Rouge XP starting 3/12/2025"
, spelled as printed. The Catalyst fork page says that a Heavy Duty chair (it gives "350 lbs weight capacity") that "has a serial number of C40043964, C50099247, CVX0099946 or after"
should use a separate heavy duty page. The Little Wave Flip foot lock page says: "This design effective starting with serial number FLP007536."
In our view, these notes are why a part number alone is not enough. Give the dealer the model, the serial number from the chair's label, the invoice date if you have the paperwork, and the page name and row you found. Ki's Catalyst 5 manual says that a UDI label is "located on your product as indicated in the figure"
; the figure is a drawing we cannot quote. In our view, find the label using the manual's figure and photograph it.
Wheel locks: Catalyst 5 and Rogue2 share the thru-post locks
The push and pull locks on the current wheel lock pages for both chairs are what Ki calls thru-post wheel locks; the Catalyst 5 keeps older locks in a folder named "Discontinued Wheel Locks". The Catalyst 5 page "Catalyst Push and Pull to Lock"
lists 27 rows; the Rogue2 page "Rogue2 Wheel Locks - Push and Pull to Lock"
lists 28; 26 part numbers appear on both. The prices below are the rows of Ki's April 2026 US retail list for those numbers.
| Part # | Description (Ki price list) | Retail (USD) |
|---|---|---|
| 124094 | Thru Post Wheel Lock Push Right Standard | $43.29 |
| 124095 | Thru Post Wheel Lock Push Left Standard | $43.29 |
| 124896 | Thru Post Wheel Lock, Push PAIR | $84.88 |
| 124098 | Thru Post Wheel Lock Pull Right Standard | $43.29 |
| 124899 | Thru Post Wheel Lock, Pull PAIR | $84.88 |
| 124102 | Thru Post Wheel Lock Push Right Reverse Mount | $45.45 |
| 124897 | Thru Post Wheel Lock, Push, Reversed PAIR | $89.12 |
| 124096 | Thru Post Wheel Lock Push Right with Extension Handle | $56.85 |
| 124901 | Thru Post Wheel Lock, Push w/ Extension PAIR | $113.71 |
| 112804 | Wheel Lock Extension | $18.31 |
| 115610 | Wheel Lock Extension with Bushing | $19.80 |
| 200369 | Wheel Lock Extension | $41.60 |
Three details on these pages change the order. Both pages say "If invoiced prior to 7/2025 pair of wheel lock will be needed"
, so an older chair may need both sides even if one lock broke. The Catalyst page adds "Notice: Chair configuration review required prior to parts being quoted or ordered"
. And the extension rows differ by page: the Catalyst page lists 200369, "Wheel Lock Extension" ($41.60), while the Rogue2 page lists 112804 ($18.31), for "replacing an extension on a wheel lock that already has one"
, and 115610 ($19.80), "when adding an extension to a wheel lock that does not already have an extension"
.
The clamps are where the two chairs part. The Catalyst page "Catalyst Wheel Lock Clamps"
lists 100641, "Wheellock Clamp CAT" ($29.86), which Ki says is "Not used with Grade Aids", and the extended top and bottom clamps 000143 and 000144 ($13.50 each), which are "Always used with Grade Aids and when Flip Back or Flip Back Height Adjustable armrests are present."
The Rogue2 page lists two complete clamp assemblies at $35.86 each: 501001, "Rigid, Standard", for the scissor locks, and 501002, "Rigid, Modified", for the push, pull and extension locks and Grade Aids. The Catalyst page also lists 500758, "Wheel Lock Ext. Clamp Assembly CAT"
($35.37), and ties the clamp to the armrest and axle plate: 100641 is used with T-Arms "when there is no Amputee Axle Plate"
, and the extended clamps "in combination with Amputee Axle Plate"
. In our reading, a lock number shared by both chairs does not make the clamp shared; order the clamp from your own chair's page.
The flush-mount and Grade Aid locks are shared too. The Catalyst page "Push to Lock Flush Mount Wheel Lock"
and the Rogue2 page "Rogue2 Wheel Locks - Push to Lock Flush Mount"
both list the kits 503828 (left) and 503829 (right); the left kit, the pages say, "contains 100648 wheel lock along with an instruction for reversing the wheel lock"
. The Catalyst page adds the PAIR 124895, which the Rogue2 page does not list. The two Grade Aid pages list the same rows: 503830 and 503831 with instructions, 502655 and 502656 with an extension, the 200369 extension, the 003415 bar and the 001321 mount bar. The Rogue2 also has an under-seat scissor page, with 100642 and 100643 and the PAIR 124914 ($90.06), and its own low profile scissor page, whose kits 117517 and 117518 are tagged "Rogue2 / Rogue DT". We did not price the flush-mount and Grade Aid kits.
Which Ki wheel lock fits a Catalyst 5 or a Rogue2? Mobility Atlas read the Catalyst 5 and Rogue2 wheel lock pages in full on 13 November 2026. For the newer thru-post push and pull locks, the two chairs list the same numbers: 124094 and 124095 for right and left push locks, 124098 and 124099 for pull locks, and PAIR numbers such as 124896. Ki's April 2026 retail list prices the single standard locks at $43.29 and the four pair numbers we looked up from $84.88 to $113.71. The clamps differ: 100641, the extended 000143 and 000144, or the extended clamp assembly 500758 on the Catalyst 5, and 501001 or 501002 on the Rogue2. Both pages say a chair invoiced before July 2025 needs a pair, and the Catalyst page asks for a configuration review before parts are quoted. In our view, send the dealer the serial number, the lock style and a photograph of the clamp.
Other Ki wheel locks: Hemi, Focus CR, Liberty and Little Wave
The Catalyst 5 also has a Hemi wheel lock, a different system with a master lock, a follower and a cable. Its page lists complete assemblies by seat width and side: 122926 and 122927 for widths 14 to 17 inches and 122928 and 122929 for 18 to 22, priced at $462.61 to $465.36 a side on the retail list. The page also lists the cables separately, 126086 and 126087, and notes the option is not available with one-arm drive at the 14 and 15 inch seat depths it names. The Catalyst 5Vx has its own page, "Catalyst 5Vx Hemi Wheel Lock"
, with its own numbers.
The tilt chairs use different hardware. The Focus CR page "Focus CR Wheel Lock" lists push and pull assemblies for each side, such as 501487 ("Wheel Lock Assembly Push Right Focus"
, $56.66) and the PAIR 501113 ($113.34), on wheel lock plates and mounts that Ki tags "Tilt". The page asks whether the chair has a combination wheel lock and points to "Standard vs Inverted Axle Plates"
as a reference. The Liberty page "Liberty Push to Lock Wheel Locks"
lists 506175 and 506176 ($58.72 each) and the PAIR 124917 ($130.00), and says: "Wheel Locks shipped unassembled, please use Technical Manual for proper setup."
For the children's chairs, the Little Wave Clik page "Clik Push and Pull to Lock Wheel Locks"
lists kits such as 503206 ("Wheel Lock Assembly, Push Right w/ Instruction"
, $45.45) and the PAIR 124906 ($80.78), and says "Please confirm wheel lock bar length and style for correct replacement parts"
. The Little Wave Flip has no hand lock page among those we saved; its "Flip Attendant Foot Lock" page lists foot lock kits by seat width from 505470 (10 inches wide) to 505478 (18 inches wide), with the serial note quoted earlier. The Rogue XP wheel lock page we saved, "Push and Pull to Lock Wheel Locks"
, carries the same "If invoiced prior to 7/2025"
note as the Rogue2 page.
General wheel lock types, wear and the questions to ask about any brand are in our wheelchair wheel lock guide.
What the manuals let an owner do with wheel locks
The Catalyst 5 manual's section U gives the same 5 mm Allen wrench adjustment and the same tire and transfer warnings that our wheelchair wheel lock guide quotes from the Rogue 2 / Rogue XP manual; one line it adds is that hangers or footrests must swing through their full range "without disengaging the wheel locks."
It goes on: "Unintentional disengagement of the wheel locks may cause a fall resulting in serious injury or death."
The maintenance table of the Catalyst 5 manual ties the locks to the tires: "Tire pressure changes and tire wear will require the wheel locks to be adjusted."
In our reading, that makes a new tire or a pressure change a reason to recheck the locks before a new lock is bought. The table's check marks sit in columns that our text extraction cannot tie to Weekly, Monthly or Annually, so we give no interval. If a lock still will not hold after adjustment, the manual's general rule applies: "If there is any doubt as to the continued safe use of your wheelchair or if any parts should fail or appear to be near failure, stop using the device immediately and contact your authorized representative immediately."
Casters, forks and caster bearings
Ki lists casters by tire type and size, one page per type. The Catalyst 5 page for 1.25 inch soft roll (poly) casters lists five sizes, 4 to 8 inches, from 100809 to 111863; the Rogue2 page for the same caster type lists 3 of them, the 4, 5 and 6 inch casters 100809, 100807 and 100786. All five soft roll sizes print $68.51 on the retail list. The Catalyst 5 also has 1 inch pneumatic casters (100520, 6 by 1 inch, $68.51, which the Rogue2 1 inch pneumatic caster page also lists; 100524, 8 by 1 inch, $69.74) and a 6 by 2 inch poly caster, 001240 ($97.41). The price list prints each caster row with no unit, so ask whether a price is for one caster or two.
The 1.5 inch soft roll casters follow the same pattern: the Catalyst 5 and Rogue2 pages both list 111842, 111843 and 111844, the 4, 5 and 6 inch sizes, and the Catalyst page adds an 8 inch caster, 105164, whose row says "Discontinued February 8th, 2021"
. The Rogue2 1 inch pneumatic page lists only the 6 inch caster, 100520, where the Catalyst page also lists the 8 inch 100524. We did not price the 1.5 inch casters. In our reading, a Rogue2 owner who wants an 8 inch caster is asking for a setup change, which brings in the fork page's matrix and the rider's therapist.
Every Catalyst 5 caster page we saved carries the same note: "If changing size of casters, new forks may be needed."
The fork page, "Catalyst Caster Forks and Stems"
, lists 67 rows: fork assemblies by caster size and stem length, such as 500509, a black fork with standard stem for 4 inch casters ($78.59), and 500511 for 5 inch casters ($68.30), color versions with the underscore suffix, stems and hardware kits. It adds that a change to 2 inch casters needs wide forks and hardware. The Rogue2 / Rogue XP fork page says to use the standard fork with a 3 to 4 inch caster and the tall fork with a 5 inch caster, and with a 6 inch caster to use the "Rogue2 Tall Fork Matrix"; the standard black fork with stem, 117512, prints at $123.70 and the tall one, 117514, at $161.76, and both rows show a quantity of 2.
Bearings are where a seller page adds detail. WheelchairBearings.com, a US seller, has a page called "Ki Mobility Wheelchair Bearings Finder"
. It names R8-2RS bearings for several Ki rear wheel types, Rogue XP and Clik forks and the Focus CR and Catalyst Performance caster mounts, and gives "Ki Mobility Bearing Part number: 100902"
; it names 6001-2RS bearings for the Catalyst series standard caster mount with Ki number 100530; and for the caster wheels it lists 608-2RS bearings with "Ki Mobility Bearing Part number: N/A"
. Ki's retail list prints 100902, an R8RS bearing, at $7.34 and 100530, a 6001RS bearing, at $14.00, with no unit. The seller's search page for "ki mobility" showed an R8 four-pack at $24.99 and a 608 four-pack at $19.99; by our arithmetic that is $6.25 and $5.00 a bearing. The fitment there is the seller's statement, not Ki's.
The Catalyst 5 manual's maintenance table asks owners to check that caster wheels, anti-tip wheels and rear wheels spin freely, says "Cleaning or replacement parts may be needed if there are any issues"
, and calls the area around the caster housing and bearings "a common location for hair build up"
. How to replace casters on any chair, and what wobble and flutter mean, are in our wheelchair caster replacement guide.
Quick-release axles and axle plates
Ki's axle pages list quick-release axles by length in millimeters. The Catalyst 5 page "Catalyst Axles" has push-button axles of 99, 104, 110 and 122 mm, plain quick-release axles of 99, 104 and 112 mm, axles with a "Quad Quick Release Lever", and fixed axles with their nuts. The Rogue2 page "Rogue2 Axles" lists a shorter set: the push-button axles of 99, 104 and 110 mm, the 99 and 104 mm plain and quad-lever axles and the quad lever itself. Both pages point to an "Axles and Receivers" reference and a "Quick Release Axle Measuring Guide"
.
| Part # | Description (Ki price list) | Retail (USD) |
|---|---|---|
| 101108 | Axle Quick Release w/ Button 1/2" x 99MM | $64.84 |
| 101182 | Axle Quick Release w/ Button 1/2" x 104MM | $64.84 |
| 101191 | Axle Quick Release w/ Button 1/2" x 110MM | $64.84 |
| 102371 | Axle Quick Release w/ Button 1/2" x 122mm | $64.84 |
| 100755 | Axle Quick Release 1/2" x 99MM | $60.01 |
| 100901 | Axle Quick Release 1/2" x 104MM | $64.84 |
| 113966 | Axle Quick Release 1/2" x 99MM with Quad Quick Release Lever | $166.57 |
| 100910 | Quad Quick Release Lever | $106.56 |
| 107413 | Universal Axle Plate, Black Anodized with Hardware Kit, Curved/Titanium Rear Frame | $184.46 |
| 107415 | Universal Axle Plate, Black Anodized with Hardware Kit, Depth Adjustable Rear Frame | $195.48 |
Each of the four push-button axles we looked up prints $64.84; the plain 99 mm axle prints $60.01, and the quad-lever axles $166.57 to $171.41. The Catalyst 5 axle plates are heavier items: the page "Catalyst 5 Universal Axle Plate"
lists plates with hardware kits for the curved or titanium rear frame (107413, $184.46) and the depth adjustable rear frame (107415, $195.48), heavy duty and color versions, and adds: "If chair was invoiced prior to November 14, 2018 and retrofitting to the universal axle plate and anti-tips are present, new anti-tip receivers are required."
Ki Parts lists no axle plate page under the Rogue2; its axles are listed under "Camber Tube and Tower Components"
, and the Rogue2 Standard Camber Mount page says to use that page when the center of gravity is between 0.5 and 5 inches (an amputee camber mount page is separate); it also says to contact Ki's customer service for some tower parts.
The axle is a safety part. The Catalyst 5 manual's rear wheel section says: "Before operating chair, assure the push button is completely extended and locking balls on the inside are fully engaged."
It warns: "Failure to do so may result in the wheel falling off, which could cause a fall or tip-over resulting in serious injury or death to you or others."
Both manuals add that if the release button does not fully extend and the balls do not lock, "the axle length needs to be adjusted."
In our view, an axle that will not lock is a reason to stop and call the dealer, not to order a longer axle by guess: the length depends on the wheel, the hub and the receiver, which is what Ki's measuring guide is for.
Where the axle sits is a setup choice, not a repair. Moving it changes the center of gravity, and the Catalyst 5 manual says the chair "should be adjusted by an authorized technician when there are changes in your weight or how you sit."
Agree any change with the rider's therapist first.
Rear tires, tubes and wheels
Ki's tire pages are split by tire type, and the Catalyst 5 and Rogue2 pages for pneumatic tires list the same numbers. Each lists kits of tire, inner tube and rim strip, such as 118216 for a 24 by 1 3/8 inch black pneumatic tire ($50.15), and the tires alone, such as 116736 ($29.14). By size, the kits run from $48.93 to $63.67 and the tires alone from $29.14 to $45.31 on the retail list. The page names the numbers they replace, such as "Replacement for part number 100635"
for the 24 inch tire.
The Catalyst 5 inner tube page lists tubes from 18 to 26 inches in 1 3/8, 1 and 2 inch widths. 6 of the 7 tubes we looked up print $14.69; the 18 inch tube, 101588, prints $24.47. For a 24 inch tire, a tire (116736) and a tube (100589) bought separately add up to $43.83 by our arithmetic, against $50.15 for the kit, which also contains a rim strip. Every tire page we saved carries the note: "Please note tab mounted handrims must be installed prior to the tire being installed."
The manuals tie tires to safety. The Catalyst 5 maintenance table says to check inflation and that "The correct inflation levels are found on the tire"
, gives a PSI to kPa conversion table, and says to check the rear tires, anti-tip wheels and caster wheels for wear spots and "Replace immediately if needed."
Tires and tubes are wear items that both manuals' warranties exclude. Tire types, sizes and pressures for any brand are covered in our wheelchair tire replacement guide, and handrims in our push rims guide.
Whole wheels are on a separate page for each type, such as "Catalyst 5 Wheels - MAXX Spoke"
and kits of wheel, tire and handrim by size. We did not save those pages, so we give no wheel prices here.
Anti-tips: four systems, different numbers
Ki's anti-tip pages show how much the right part depends on the chair. The Catalyst 5 page "Catalyst Rear Anti-Tip" lists four tubes by length, and its descriptions name chairs and wheel sizes: 119669 is "Anti Tip Medium 22/24CAT 18/20 Rogue-LW 22/24/25ETHOS"
in the parts manual. The four print $66.25 to $70.83 on the retail list. The page notes: "If changing to or from a reclining configuration, new sized anti-tips may be required."
and "If retrofitting, Anti-Tip Receivers are needed."
The Catalyst 5 also has a swing-in anti-tip, sold as a pair (107720 short, for a rear seat height under 16 inches, and 107721 long, for 16 inches or greater, $367.06 each) or as single assemblies and replacements chosen by the same seat height; its page says it is "Not available with Heavy Duty Option"
.
The Rogue2 / Rogue XP page "Rogue2 / Rogue XP Rear Anti-Tip"
lists anti-tip assemblies by rear wheel size (117468 for 22 inch wheels and 117469 for 24 to 26 inch, $70.83 each) and complete receiver assemblies by wheel size and side (the four we looked up, for 18-20 and 24-26 inch wheels, print $81.19). It also lists 119669, the same medium tube as the Catalyst page. The Rogue2 user activated anti-tip is a different part: complete assemblies 117507 to 117509 and the X-large 117590 all print $277.48, and the page says complete assemblies contain one anti-tip and "Quantity two is required for a pair."
By our arithmetic, a pair is $554.96 at retail.
The tilt chairs use their own anti-tips. The Focus CR page says "Anti-Tip assemblies are based on rear wheel size."
and lists pairs for 12 to 16, 20 to 22 and 24 inch wheels ($171.28 a pair) and single assemblies for each size, such as 501483 (12 to 16 inch, tagged "Tilt", $85.65). The Liberty page lists anti-tips by wheel size, 119676 to 119679, at $47.06 to $58.55. The Little Wave XP page "Rigid Rear Anti-Tip" lists the same four tubes, 119669 to 119672, as the Catalyst page, with the note "Used if Alber Emotion/Twion system is present on a Rogue XP"
; the Flip page "Flip Rear Anti-Tip" lists its own kits, which we did not price.
The Catalyst 5 manual's anti-tip warning says: "Always keep anti-tips in the down position when they are not at risk of interference. Have a clinical or technical professional confirm your anti-tips are installed in the correct position."
and that a wrongly set chair "could result in the wheelchair tipping over. Tipping over could result in damage to your wheelchair, serious injury or death."
In our reading, the tube lengths above are why: the same tube 119669 is listed on the Catalyst, Rogue2 / Rogue XP and Little Wave XP pages, but which length a chair needs depends on its wheel size, seat height and back, and the Catalyst page says a change to or from a reclining back may need new sized anti-tips. The Rogue 2 / Rogue XP manual's anti-tip warnings, and how anti-tippers work on any brand, are in our wheelchair anti-tipper guide.
Footrests, hangers and footplates
The Catalyst 5 and the Rogue2 are built differently at the front, and their footrest pages show it. The Catalyst 5 is a folding chair with swing-away hangers: its "Footrests" folder has hanger pages by angle and mount (60, 70 and 80 degree extension mount; 70, 80 and 90 degree front mount), elevating leg rests, extension tubes and footplates. The Rogue2 is rigid: each footrest page for it lists footrest tubes and footplates that fit into the frame, from "Rogue2 Footrest - Tubular Open"
to angle adjustable and flip-under types.
| Part # | Description (Ki price list) | Retail (USD) |
|---|---|---|
| 100537 | Footplate Composite 14-15" Wide CAT/TILT | $42.82 |
| 100540 | Footplate Composite 16-17" Wide CAT/TILT | $42.82 |
| 100542 | Footplate Composite 18-24" Wide CAT/TILT | $42.82 |
| 107605 | Footplate Kit Aluminum Locking Multi-Angle Adjustable, 14-15" Wide, Right | $378.71 |
| 107620 | Footplate Hardware Kit Aluminum Locking Multi-Angle Adjustable, PAIR | $709.16 |
| 003416 | Classic Hanger Latch Assembly, Right | $74.28 |
| 003225 | Assembled 4-Way In Line Hanger Release | $42.82 |
| 124000 | Angle Adjustable Footplate 6" with Hardware | $91.56 |
| 124001 | Angle Adjustable Footplate 7" with Hardware | $77.21 |
| 124002 | Angle Adjustable Footplate 8" wih Hardware | $99.88 |
| 000214 | Footrest Tubular 12" Rigid | $87.85 |
| 501741 | Footrest Protector w/ Instructions Kit PAIR Rigid | $31.21 |
The first seven rows come from Catalyst 5 pages; the last five from Rogue2 pages. On the Catalyst side, the hanger pages list complete hangers with a color suffix, such as 100419_ _ _ for a right 60 degree extension mount hanger with a classic latch, and the latch and release parts on their own. Those pages warn that "If changing degree of hanger, new extension tubes may be needed."
The composite footplate page says "Sizes for footplates are based on seat width."
and "Only compatible with extension tube hangers."
The aluminum locking multi-angle page says "Only compatible with Front Mount Hangers."
and "Sizes for footplates / assemblies are based on seat width."
On the Rogue2 side, the page "Rogue2 Footrest - Aluminum Angle Adjustable"
lists angle adjustable footplates of 6, 7, 8, 9, 10 and 12 inches (we priced the 6, 7 and 8 inch ones), each row naming the footrest tube widths, tapers or seat-to-footrest lengths it is used on; 124001, for example, is listed for straight footrest tubes 12 inches wide with no taper, among other widths. The tubular footrest page says "If changing seat widths, new foot tubes will be needed."
and the flip-under page says "If changing width of chair, new footrest tubes are required."
In our reading, a Rogue2 footrest is ordered from the chair's width and taper, not from the old footplate alone.
The hanger pages carry more conditions than the footplate pages. Each Catalyst hanger page we saved says: "If chair was built with a fixed front frame or hangers were omitted, then latch blocks need to be ordered with hangers."
The 60 degree extension mount page adds "If changing hanger style, new footplate hardware may be needed."
and "If switching from a contracture footrest to a standard hanger, front seat tubes and latch blocks with hardware will be needed."
In our reading, a hanger is ordered by angle, mount, latch type and side, and a change of any of those can pull in tubes, latch blocks or footplate hardware. Owner adjustment of Rogue2 footrests, from the Rogue 2 / Rogue XP manual, is in our wheelchair footrest guide.
Armrests and side guards
Armrest assemblies print in the hundreds of dollars on Ki's list. The Catalyst page "Catalyst Height Adjustable T-Arm"
lists complete assemblies by side panel length and pad, single and PAIR; 505499 (long side shield, standard full pad, 1 inch receiver) prints $314.89 and its pair 505500 $629.78; the page also lists assemblies without the 1 inch receiver (such as 505491) and notes "Receiver and Hardware update effective 11/25/24"
, so ask the dealer which receiver your chair has. The page says "Short assemblies are used with 14-17 Seat Depths."
and puts the long assemblies on 18 to 20 inch seat depths, and adds "If retrofitting, Receivers are needed."
The Rogue2 page "Rogue2 Armrest - Swing Away"
lists short and tall swing-away arms with receivers; 117134 (short, right) prints $310.60 and the short PAIR 117136 $621.19.
The Rogue2 swing-away page prints a rule for short against tall arms, by rear wheel size and rear seat height. For 24 inch wheels it says to use the tall arm at a rear seat height of 14.5 to 16.5 inches and the short arm at 17 inches or greater, with other lines for 20, 22, 25 and 26 inch wheels. The Rogue2 height adjustable T-arm page says: "Height Adjustable T-Arms cannot be retro-fitted."
The Catalyst flip back armrest page warns that a retrofit needs receivers and new front frames, and that "Extended wheellock clamps may be needed"
, which links back to the wheel lock clamp rows above.
Side guards show a part shared on paper but split by size. The Catalyst 5 page "Catalyst 5 Side Guards - Removable Adult Composite"
lists front drilled assemblies (112575, 112576 and the PAIR 112577) for folding chairs 17 inches deep or less and rear drilled assemblies (112578, 112579, PAIR 112580) for folding chairs 18 inches deep or greater. The Rogue2 page "Rogue2 Side Guards - Removable Composite"
lists only the rear drilled assemblies. Each single assembly prints $95.88 and each pair $191.77. Both pages say receivers may be needed when retrofitting; the Rogue2 receiver page adds "If retrofitting side guards, clamp on receiver is required"
.
Two armrest pages share numbers across the chairs. The Catalyst page "Catalyst Height Adjustable T-Arm"
and the Rogue2 page "Rogue2 Armrest - Height Adjustable T-Arm"
both list four complete assemblies with a short side shield: 505644 ("Height Adjustable T-Arm Assembly w/ Short Side Shield and Standard Pad Full"
) and its pair 505645, and 505646 (the same with a desk pad) and its pair 505647. The Rogue2 page still says the arms "cannot be retro-fitted", so in our reading those shared numbers replace an existing T-arm on a Rogue2 rather than convert a chair that came without one. The swing-away arms are not shared: the Catalyst swing-away page and the Rogue2 page list different numbers. The Catalyst 5 manual, in its section on the height adjustable T-arm, warns: "These arms offer only a lock against rotation and are designed to bear a downward force only. Failure to comply with the instructions above may result in a fall or loss of control and may cause serious injury or death."
The Rogue 2 / Rogue XP manual's armrest warnings, and armrest types across brands, are in our wheelchair armrest guide.
Backs, push handles and upholstery
On the Catalyst 5, push handles are part of the back posts. The page "Catalyst Straight Backrest with Push Handle"
lists back post assemblies in short, medium and tall, with standard or low profile handles; 100715 (short, standard handle) and 100716 (medium) print $84.56 each. It lists separate back tubes for chairs with a drum brake and the locking grip 122545 ($9.84). The page notes: "Low Profile Push Handles are not available with Heavy Duty Option or Drum Brake"
. The fold down push handle has its own page.
On the Rogue2, push handles can bolt to the back. The page "Rigid Bolt-On Push Handle"
lists tubes by back height: angle drilled tubes by side, and straight drilled tubes listed with a quantity of 2; the three 9 to 11 inch tubes we looked up (102458, 102464, 102508) print $47.95, with no unit on the list; the page also offers complete assemblies, 501450 to 501467, each of which "contain one Bolt-On Push Handle assembly"
. The page explains the choice: "Angle Drilled Bolt-On Push Handles are used on chairs with Omit Push Handles or Double Stroller Handles."
and "If an Axiom Back is present on the chair, the Straight Drilled Bolt-On Push Handles are required."
Upholstery is the part this guide covers least. Ki Parts has pages for seat and back upholstery under each chair, such as "Catalyst Standard Back Upholstery"
and five tension adjustable back pages for the Catalyst, but we did not save them and give no numbers or prices. Both manuals we read list upholstery among the wear items their warranties exclude, and the Catalyst 5 maintenance table says: "Check upholstery for signs of wear, fraying or holes. Replace upholstery immediately if needed."
Upholstery choices across brands are in our wheelchair seat upholstery guide.
Grips are small but listed in the same maintenance table: "Check that the hand grips do not rotate or pull off. Replace if needed."
On the Catalyst 5 that is a locking grip from the back post page; on a Rogue2 with bolt-on handles, ask the dealer which grip the handle page lists.
What the manuals let an owner adjust
Ki's manuals draw a line between owner adjustments and technician work. The Catalyst 5 manual's maintenance section says: "Common tools to perform user authorized maintenance include: Tire pressure gauge, open end metric wrenches and metric allen wrenches."
and "Any maintenance check that you are not comfortable performing should be done by an authorized supplier."
Its troubleshooting table marks each fix A, "Self Correct if capable or contact Authorized Distributor"
, or B, "Contact Authorized Supplier or Distributor"
; tightening spokes and optimizing the CG setting are marked B.
On modifications, the Catalyst 5 manual is blunt: "NO ONE SHOULD MODIFY THIS WHEELCHAIR EXCEPT BY ADJUSTING IT ACCORDING TO THIS MANUAL OR BY ADDING KI MOBILITY APPROVED OPTIONS."
It adds that there are no approved options involving drilling or cutting the frame by anyone other than a trained Ki associate, and says to contact an authorized supplier or Ki "before adding any accessories or components not provided by Ki Mobility."
It warns: "Unapproved modifications or options could lead to fall and cause serious injury or death."
In our reading, a non-Ki part that fits by eye is outside what the manual allows.
Within those limits, the Catalyst 5 manual gives owners steps for the wheel locks, rear wheels, armrests, hangers, extension tubes, leg rests, anti-tips and drum brakes. The Rogue 2 / Rogue XP extracts give steps for the wheel locks, footrest height and angle, armrests and anti-tips. Both manuals set fastener torques in places, such as "40 in./lbs" in the Catalyst 5 maintenance table for fasteners unless otherwise noted, which in our view means a torque wrench belongs in the toolkit of anyone doing their own work.
After storage, the Catalyst 5 manual says: "If your chair has been in storage for more than two months, it should be serviced and inspected by an authorized supplier before use."
Repairs that are not part swaps, such as a bent frame or a cracked weld, are covered in our manual wheelchair repair guide.
What Ki parts cost on Ki's US retail list
What do Ki Mobility parts cost? On Ki's own US retail list, effective 1 April 2026, the 33 part numbers in five groups of our price table (single thru-post locks, push-button and plain quick-release axles, casters, inner tubes and pneumatic tire kits) print $14.69 to $97.41, while quad-lever axles, armrests, axle plates and some lock systems print more. Mobility Atlas read the price rows for 148 Ki part numbers on 13 November 2026. A thru-post push lock prints $43.29 a side, a 1.25 inch soft roll caster $68.51 and a 24 inch pneumatic tire kit $50.15. Among the 148 numbers we looked up, the highest is the aluminum locking multi-angle footplate hardware kit PAIR 107620 at $709.16; a Catalyst height adjustable T-arm pair with 1 inch receiver (505500) prints $629.78 and a Hemi lock assembly $462.61 to $465.36 a side. These are Ki's published retail figures; a dealer sets its own price and adds fitting, shipping and tax.
| Group (part numbers priced) | Chairs whose pages list them | Retail range (USD) |
|---|---|---|
| Thru-post locks, one side (7) | Catalyst 5, Rogue2, Rogue XP | $43.29 to $56.85 |
| Thru-post locks, PAIR (4) | Catalyst 5, Rogue2, Rogue XP | $84.88 to $113.71 |
| Wheel lock clamps (6) | Catalyst 5 (4), Rogue2 (2) | $13.50 to $35.86 |
| Hemi lock assemblies (4) | Catalyst 5 | $462.61 to $465.36 |
| Other chairs' lock assemblies (10) | Focus CR, Liberty, Little Wave Clik | $45.45 to $130.00 |
| Quick-release axles, button or plain (7) | Catalyst 5; Rogue2 lists 5; Rogue XP drum brake and Flip foot lock pages list 101108 (Flip also 101191) | $60.01 to $64.84 |
| Casters (8) | Catalyst 5; Rogue2 lists 4 | $68.51 to $97.41 |
| Fork assemblies (4) | Catalyst 5 (2), Rogue2 (2) | $68.30 to $161.76 |
| Anti-tip tubes 119669-119672 (4) | Catalyst 5; Rogue2 lists 3; Little Wave XP lists 4 | $66.25 to $70.83 |
| Rogue2 anti-tip assemblies (6) | Rogue2 | $70.83 to $81.19 |
| User activated anti-tips (4) | Rogue2; Rogue XP lists 3 | $277.48 |
| Focus CR and Liberty anti-tips (8) | Focus CR, Liberty | $47.06 to $171.28 |
| Pneumatic tire kits (4) | Catalyst 5, Rogue2 | $48.93 to $63.67 |
| Inner tubes (7) | Catalyst 5 | $14.69 to $24.47 |
| Footplates (7) | Catalyst 5 (4), Rogue2 (3) | $42.82 to $378.71 |
| Side guard assemblies, one side (4) | Catalyst 5; Rogue2 lists 2 | $95.88 |
Counting rules: each group is the part numbers we looked up for that part type from the saved assembly pages, some of which the text does not name; each price is the row printed for that number in Ki's list. A group lists the chairs whose parts manual pages we saved and that list those numbers; it is not a statement that the part fits any other chair. The price list prints no unit for the rows we looked up, so where a description says PAIR we say pair, and otherwise we say a side or give no unit. Prices checked November 2026.
Pair or two singles: what the arithmetic shows
Because Ki prints both a single and a PAIR number for many parts, we checked whether a pair costs less than two singles. For the standard thru-post push lock, two singles (124094 and 124095) come to $86.58 and the PAIR 124896 prints $84.88, $1.70 less. For five of the other seven pairs we checked, the difference is two cents or less either way: the push lock with extension pair prints $113.71 against $113.70 for two singles, the Rogue2 short swing-away arm pair $621.19 against $621.20, and the Catalyst front drilled side guard pair $191.77 against $191.76. Two lock pairs go further: the Liberty push PAIR 124917 prints $130.00 against $117.44 for two singles, $12.56 more, and the Clik push PAIR 124906 prints $80.78 against $90.90 for the two single kits (which add a reversing instruction), $10.12 less.
In our view, for most of the pairs above the reason to order a pair is not price. The Catalyst 5, Rogue2 and Rogue XP push and pull lock pages say a chair invoiced before July 2025 needs a pair (the Focus CR, Liberty and Clik pages we saved carry no such note); a pair keeps both sides at the same wear; and the Catalyst 5 manual, in its anti-tip warnings, says "Ki Mobility recommends using two anti-tips on your wheelchair. Use of a single anti-tip increases the risk of tipping over backwards. Tipping over backwards could result in damage to your wheelchair, serious injury or death."
The reason to order a single is that only one side is damaged and the pages allow it. Ask the dealer which applies to your chair and serial number.
One more comparison concerns tires. A 24 inch kit (118216) prints $50.15, while the tire (116736) and tube (100589) alone come to $43.83; the kit adds a rim strip. Whether the old rim strip can be reused is a question for whoever fits the tire.
What seller pages show for Ki parts
Ki parts were hard to find on the US seller pages we checked. Sportaid's site search for "ki mobility" printed "Showing 1–16 of 29 results"
; on the first page we loaded, none of the 16 tiles named Ki, and they were chairs, parts and supplies from other makers. Its search for "catalyst" returned a single result, a digestive enzyme product. We did not load Sportaid's second results page.
WheelchairBearings.com's search for "ki mobility" returned 9 results, all bearings, tools and Reckless Wheelchairs parts, with no Ki-made part among them; its "Ki Mobility Wheelchair Bearings Finder"
page is the seller's own guide to which bearing it says fits which Ki part, quoted in the caster section above. Its scissor brake pair tiles print "Original price" $174.99 and "Current price" $144.99. Those are Reckless Wheelchairs brakes, not Ki locks, and no page we read says they fit a Ki chair.
In our reading, the absence of Ki-made parts on these pages fits Ki's own instruction to buy through a dealer. It also means the retail list is the main public price reference for Ki numbers. We found no Ki part priced by a US seller below or above Ki's list, so we make no claim either way.
Warranty on Ki parts: what the two manuals print
Both manuals we read list "Wear items: Upholstery, tires, armrest pads, tubes, armrests and push-handle grips."
among what they do not warrant, and both say the owner must "Pay any charges for labor to repair or install parts."
The full terms for each Ki manual, including how claims run through an authorized supplier, are in our Ki Mobility guide.
Recall records for Ki chairs
Our searches of openFDA recall data on 13 November 2026 (last_updated 2026-11-12), by recalling firm and by a word search for Ki model names, returned one record, Z-0467-2022 (initiated 2021-11-19, status Terminated), about the manual supplied with the Little Wave Tyke, a chair outside this guide; none named the Catalyst, Rogue, Focus CR, Liberty or the Little Wave chairs we covered. The record is set out in our Ki Mobility guide, and both Ki manuals we read say: "Contact Ki Mobility for information on safety recalls and notices."
Medicare and other funders
We did not read Medicare's, Medicaid's or the VA's rules for this guide, so we say nothing about whether a program pays for a Ki part. How Medicare treats repairs and replacement parts in the US, and who may bill for them, is set out with its sources in our wheelchair parts guide; for any other plan, ask the plan.
Ordering Ki parts through Mobility Atlas
Mobility Atlas can find and quote a Ki part, including parts that are not listed in our catalog. Our catalog lists Ki chairs but no Ki-made parts, so for a Ki part you send a part request naming the chair, the part and, if you have it, the Ki part number and serial number. The wheelchair parts and accessories page shows the parts we list and the part request link.
The process is short: you send an enquiry or a part request, we reply with a written quote that includes delivery to your country, and nothing is charged before you accept it. In our view, the most useful request includes the model, the serial number, the invoice date if known, the Ki Parts page and row, the side, a photo of the old part and the name of the person who will fit it.
Three traps
The shared number, different clamp. The Catalyst 5 and the Rogue2 list the same thru-post lock numbers, so a lock from one chair's page looks like a match for the other. The clamps are not shared: 100641, the extended 000143 and 000144, or the extended clamp assembly 500758 on the Catalyst 5, and 501001 or 501002 on the Rogue2. Order the clamp from your own chair's page, and remember the note on the Catalyst 5, Rogue2 and Rogue XP push and pull lock pages that a chair invoiced before July 2025 needs a pair of locks.
The invoice date and serial number you did not write down. Several Ki pages change with dates or serials: the Rogue XP User Activated Anti-Tip page says "Used on chairs invoiced starting on 3/12/25"
, while the Clik User Activated Anti-Tips page says "Used on Rogue XP invoiced prior to 3/12/25."
The Catalyst fork page sends heavy duty chairs above certain serial numbers to another page. Without the invoice date and the serial, a dealer cannot tell which page applies.
The price list is not a fitment list. Ki's retail list prints descriptions like "Wheel Lock Assembly, Push Right"
with no chair named, and sorts by part number. A part's presence on the list says nothing about which chair it fits; only the parts manual page does. Likewise, a seller's statement that a bearing fits a Ki chair is the seller's, not Ki's.
Three composite scenarios
These are composite scenarios, not individual customers. Each uses only the documents named for that model.
Scenario one: a Catalyst 5 rider's right push lock no longer holds on a ramp after a new pair of tires. The Catalyst 5 manual says "Tire pressure changes and tire wear will require the wheel locks to be adjusted"
, so the rider first follows the manual's steps with a 5 mm Allen wrench and tests on a flat level surface. The lock still slips, and its handle is cracked. The manual says: "If there is any doubt as to the continued safe use of your wheelchair or if any parts should fail or appear to be near failure, stop using the device immediately and contact your authorized representative immediately."
The rider uses another chair and calls the dealer, who reads the Catalyst page: the chair was invoiced in 2024, so a pair is needed; after the configuration review the page requires and a check of the orientation reference, the dealer quotes the standard push pair 124896 ($84.88 at retail) with fitting.
Scenario two: a Rogue2 rider's right swing-away armrest is bent after it hits a door frame, and it no longer sits firmly. The Rogue 2 / Rogue XP manual says: "If there is any doubt as to the continued safe use of your wheelchair or if any parts should fail or appear to be near failure, stop using the device immediately and contact your authorized representative immediately."
The rider uses a spare chair and calls the dealer. The Rogue2 page "Rogue2 Armrest - Swing Away"
decides the length: with 24 inch wheels and a rear seat height of 17 inches, its rule says the short arm. The dealer quotes 117134, the short right arm with receiver ($310.60 at retail). Armrests are wear items under the manual's warranty, so the rider pays for the part and, as the manual says, "any charges for labor".
Scenario three: a Rogue XP user's family wants a second set of user activated anti-tips. The Rogue 2 / Rogue XP manual says "Ki Mobility recommends training by an Assistive Technology Professional (ATP) or other competent clinical or technical professional in the safe use of this chair prior to use."
and Ki Parts has two pages: "Rogue XP User Activated Anti-Tip"
, "Used on chairs invoiced starting on 3/12/25"
, and the Clik page used on Rogue XP chairs invoiced before that date. The family finds the invoice, dated before March 2025, and sends the dealer the serial number; the dealer checks the page's notes that a pair is "not available if a tipping lever is present"
, not with one arm drive or the E-motion ready option, and that chairs with more than 2 [units garbled in our copy] of variance between front and rear seat height go to Customer Service; the dealer orders two assemblies from the Clik page, because Ki says one assembly is one anti-tip, and the therapist checks the setting.
Questions to ask before you order a Ki part
- Which Ki Parts page and row does this part come from, and does that page sit under my chair's model?
- Does the page carry a date or serial note, such as the July 2025 wheel lock note or the 3/12/25 Rogue XP note, and does my chair fall before or after it?
- Is the price for one side, a pair or a kit, and what is Ki's April 2026 retail price for that number?
- Do I need a matching clamp, receiver, extension tube or fork with this part, as the page's notes say?
- Will the change alter my setup (axle position, anti-tips, footrest height, armrest type), and has my therapist agreed to it?
- Who fits the part, what does fitting cost, and who checks the wheel locks and anti-tips afterward?
- Is the part under warranty, or is it a wear item that both manuals exclude, and who pays labor?
In our view, the answers are worth having in writing before any part is ordered.
Sources and documents
We read every source below on 13 November 2026, including the four Rogue 2 / Rogue XP manual extracts saved by our team that day for earlier guides. The Ki parts manual and the price list are live documents and may change; our figures are as printed on that date.
Ki's documents are the primary sources: Ki Parts (the parts manual), the US retail parts price list, the Catalyst 5 and Rogue 2 / Rogue XP owner's manuals and Ki's Contact and Warranty pages. Seller pages from Sportaid and WheelchairBearings.com show what those sellers printed; openFDA shows the recall record as stored.
This article is general information. Rules and prices differ by country and change, so confirm them before you buy or travel.
Common questions
Can I buy Ki Mobility parts directly from Ki?
Ki's own pages send riders to a dealer. Its Contact page says: "For service or repair parts for your personal device, please click here to find a dealer near you."
Its manuals tell owners to contact an authorized service representative for parts information, identification and ordering. Ki Parts and the US retail price list are public, so you can name the part and its retail price before you ask.
Where do I find the right Ki part number?
Open Ki Parts from the Resources menu on Ki's website, choose Search By Wheelchair, then Rigid, Folding or Tilt-In-Space, your chair, the part group and the assembly. Read the notes above the table, since some pages split parts by invoice date or serial number, and copy the part number, including any suffix, and the side exactly. Give the dealer that number with your serial number.
Do Catalyst 5 parts fit a Rogue2?
Only where both chairs' pages list the same number. On the pages we read, both list the thru-post wheel locks, the 1.25 and 1.5 inch soft roll casters in 4 to 6 inch sizes, the 6 by 1 inch pneumatic caster 100520, the pneumatic and high pressure tires and three of the four full poly tires, the push-button axles of 99, 104 and 110 mm and the plain and quad-lever axles of 99 and 104 mm, three anti-tip tubes (119669, 119670, 119672), the rear drilled side guards and four short height adjustable T-arm assemblies (505644 to 505647). The wheel lock clamps, forks, anti-tip assemblies, footrests and swing-away arms differ. Order from the page for your own chair.
What do Ki wheelchair parts cost?
On Ki's US retail list, effective April 2026, a thru-post push lock prints $43.29 a side and $84.88 a pair, a quick-release axle with a button $64.84, a 24 inch pneumatic tire kit $50.15 and a Catalyst height adjustable T-arm pair with 1 inch receiver (505500) $629.78. Dealers set their own prices, and fitting, shipping and tax come on top.
Are Ki parts covered by warranty?
Many are not: both manuals we read list "Wear items: Upholstery, tires, armrest pads, tubes, armrests and push-handle grips."
among what they do not warrant, and both leave labor to the owner. Ki's full warranty terms, manual by manual, are in our Ki Mobility guide.
Can I fit Ki parts myself?
The manuals allow some owner work, such as adjusting wheel locks with a 5 mm Allen wrench and setting footrest angle, and list the tools for user authorized maintenance. Both say set up should be done only by an authorized technician, and the Catalyst 5 manual warns: "NO ONE SHOULD MODIFY THIS WHEELCHAIR EXCEPT BY ADJUSTING IT ACCORDING TO THIS MANUAL OR BY ADDING KI MOBILITY APPROVED OPTIONS."
and "Unapproved modifications or options could lead to fall and cause serious injury or death."
Both manuals say: "If there is any doubt as to the continued safe use of your wheelchair or if any parts should fail or appear to be near failure, stop using the device immediately and contact your authorized representative immediately."
Sources
- Ki Mobility: Ki Parts (Parts Manual), Search By Wheelchair, category tree for nine chairs
- Ki Mobility: Ki Parts assembly pages for the Catalyst 5, Catalyst 5Vx, Rogue2, Rogue XP, Focus CR, Liberty and Little Wave XP, Clik and Flip (76 pages)
- Ki Mobility: US Ki Retail Parts Pricing, effective 04/01/2026 (PDF)
- Ki Mobility: Catalyst 5 User Instruction Manual and Warranty, English-Spanish (PDF)
- Ki Mobility: Rogue 2 / Rogue XP User Instruction Manual and Warranty, cover dated 2025-02-13 (PDF)
- Ki Mobility: Contact Us
- Ki Mobility: Warranty
- WheelchairBearings.com: Ki Mobility Wheelchair Bearings Finder
- WheelchairBearings.com: search results for ki mobility
- Sportaid: search results for ki mobility (first page)
- Sportaid: search results for catalyst
- openFDA: device recalls, recalling firm ki mobility
- openFDA: device recalls, word search for Ki model names in product descriptions
Read on . The wording of the article is our own.




