Stair lift parts guide 2026: stair lift battery, stairlift remote, chargers, seat belts, rails, stair lift replacement parts, prices, warranty and recalls
Stair lift parts as Bruno, Harmar, Handicare, Stannah and Acorn documents print them: batteries, remotes, chargers, seats, belts, rails, US prices, warranty and recalls.
Contents
- The short answer
- How we checked, and what we read
- The parts of a stairlift, as the documents name them
- Before you order: model, serial number and the battery label
- Stair lift battery: type, voltage and amp-hours, as printed
- How long a stair lift battery lasts, and what shortens it
- Chargers, charging strips and charging stations
- Stairlift remote and call stations
- Error codes, beeps and lights, as the manuals print them
- Seat, swivel, armrest and footrest parts
- Safety edges, obstruction sensors and seat belts
- Rails, gear racks, folding rails and keys
- Who may replace what, according to the documents
- Warranty by document: motor and gearbox, parts, batteries, labor
- Stairlift recalls: what the FDA and CPSC records show
- What stair lift replacement parts cost: two US sellers on 19 November 2026
- Maker parts, look-alike batteries and used parts
- Medicare, Medicaid and other payers
- Three traps
- Three composite scenarios
- Questions to ask the dealer, the seller or the maker
- Sources and documents
- Common questions
- Sources
The short answer
Stair lift parts fall into two groups. The first group is what the owner's manuals let you change at home: the batteries in the hand-held remote, a charger fuse on one Bruno model, and keeping the lift parked on its charge point. The second group is everything inside the lift and on the rail, in our reading: the main stair lift battery pack, the motor and gearbox, the control board, safety edges, swivel parts, the rail and gear rack. In our reading of the Bruno, Harmar, Handicare and Stannah documents, that second group goes through the dealer or a trained engineer. Harmar's SL600 owner's manual says "Do not attempt to service the lift yourself. Contact your Harmar dealer for assistance."
and, for the main batteries, "Contact your local dealer for proper battery replacement."
This guide goes part by part: stair lift battery type, voltage and amp-hours where a document prints them, chargers and charge strips, the stairlift remote and call stations, seats, swivels, footrests, safety edges, seat belts, rails and keys. For each part we give what the maker's document says, who may replace it, what the warranty says, and what two large US online sellers charged for replacement batteries and chargers on 19 November 2026. We also list the stairlift recalls in the FDA and CPSC records, with their dates and status.
Mobility Atlas earns a fee or margin when you order through us; this guide uses the stairlift makers' own manuals, warranty pages and product pages, two US sellers' search pages, and US Food and Drug Administration and Consumer Product Safety Commission recall records, each read on the date we give.
Mobility Atlas can find and quote a stairlift part for you, including parts that are not listed on our pages. Our transfer and lifting equipment page lists a stairlift but no stairlift parts, so send a part request naming the stairlift maker, the model, the serial number and the part you need. The process: you send an enquiry or a part request, we reply with a written quote that includes delivery to your country, and nothing is charged before you accept it.
If you are choosing a new stairlift rather than repairing one, start with our stairlift guide, and for one maker in depth, the Stannah guide. A platform lift that carries a person seated in a wheelchair is a different device, covered in the wheelchair lift guide. Parts for powered recliners are in the lift chair parts guide.
How we checked, and what we read
Method: we saved each page or PDF as text with its address and the date we read it, extracted the PDFs in the browser, and computed every count and price range by script from the saved text. Quotes are copied from the saved text. Where a fact comes from one model's manual, we name that manual and do not stretch it to other models.
The maker documents are these. Bruno: the SRE-2010 Elite straight rail stairlift operator's manual, P/N 2010-O, dated 08 February 2019, with the "Bruno Gold" stairlift warranty (rev. 04-18) on its last English page; the SRE-3000 Elan installation manual, P/N 3000-I, dated 08 February 2019, a dealer document with the same warranty and an exploded view with part numbers; and the Elan product page on bruno.com. Harmar: the Pinnacle SL600 owner's manual (23JULY2024, 76016 G) and the SL600 product page, both on harmar.com. Handicare: the Handicare 1100 user manual and the Freecurve user manual (11P00388 rev.B, marked UK). Stannah: the 600 Siena user guide, Issue 3, January 2013, a UK document. Acorn: three pages of the Acorn US website and its two-page quick user guide for the 130 and 180 lifts.
Two Bruno manuals, both Handicare manuals and the Stannah guide are copies on a Shopify file server (cdn.shopify.com), not on the maker's website; Bruno's own manual search did not load from our browser. In our view, ask your dealer for the manual that matches your serial number, because a 2013 or 2019 manual may not match a lift built later.
Prices come from the first results page of two US sellers, Zoro and Walmart.com, for the searches "stairlift battery" and "stairlift charger" (Zoro) and "stairlift battery" (Walmart). A second Walmart search, for stairlift remotes, stopped at a robot check, which we did not try to pass; an eBay search for "stairlift remote" showed prices in Thai baht in our browser, so we did not use its prices. Recalls come from the openFDA device recall data (last updated 2026-11-14) and enforcement data (no match, no update date returned), and the CPSC recall database and recall page. We did not read Medicare, Medicaid or VA rules for this guide.
The parts of a stairlift, as the documents name them
Makers use different words for the same part. Bruno calls the hand-held remote a "transmitter" and Stannah a "remote calling control"; Harmar calls it a "call/send hand control unit"
. Bruno says "positioning belt" or "lap belt", Harmar "seatbelt", Handicare "safety belt". In our view, search with the maker's word when you look for a part, and give the seller the maker's part name and number.
| Part | What the documents call it | Who changes it (our reading of each document's service line) |
|---|---|---|
| Main batteries in the carriage | Bruno Elan: "two (2) 12-volt sealed, maintenance-free batteries"; Harmar: "batteries" | Harmar manual: the local dealer; Bruno warranty: authorized dealer for repair work |
| Charger or power supply | Bruno: "Battery Charger", 24VDC; Stannah: "Battery charger", output 24V DC 750mA | Bruno Elite manual: owner may replace the charger's AC fuse with the same type |
| Charge strips and charge points | Bruno: "bronze charge strips"; Harmar: "charge strip stations"; Handicare: "charge points" | Bruno installation manual: dealer, with gloves |
| Remote / call station | Bruno: "remote transmitters"; Stannah: "remote calling controls"; Harmar: "call/send hand control unit" | Owner changes the remote's AA batteries (Bruno, Stannah); reprogramming is in Bruno's dealer manual |
| Seat, swivel, armrests | Bruno: "Folding, Swivel Seat", "Seat Swivel Release"; Harmar: "Seat swivel release bars" | Dealer |
| Footrest | Bruno manual: "Folding Footrest (with obstruction sensors)"; Harmar manual: "Footrest with obstruction sensors" | Dealer |
| Safety edges and sensors | Stannah: "Safety edges"; Harmar: "spring loaded sensors"; Bruno: "carriage safety panels" | Dealer |
| Seat belt | Bruno: "Lap Belt"; Harmar: "retractable seat belt"; Acorn: "Inertia seatbelt" | Dealer |
| Rail and gear rack | Bruno manual: "vertical aluminum extrusion with integral drive gear rack"; Harmar page: "nylon polymer gear rack" | Dealer; Acorn FAQ: shortening by an Acorn approved engineer |
| Key switch | Bruno: "keyswitch"; Stannah: "Power key"; Harmar: optional "Key lock" | Not printed (in our view, ask the dealer for a spare) |
Sources for the table: Bruno SRE-3000 installation manual pages 4 and 7; Bruno SRE-2010 operator's manual pages 4, 14 and 16; Harmar SL600 owner's manual pages 6, 7 and 14 and SL600 page; Stannah 600 Siena guide pages 7 and 18; Handicare Freecurve manual page 11; Acorn US stairlifts page and FAQ.
Before you order: model, serial number and the battery label
The Bruno, Handicare and Harmar manuals ask for the serial number before service or parts. Bruno's Elite manual says "Serial and model numbers must be provided when filing a warranty claim, requesting service or ordering parts."
It says "The serial number is found on labels affixed to the manual, as well as on the unit itself."
Handicare's 1100 manual says the stairlift serial number "can be found on the label located on the power pack underneath the seat."
Stannah's 600 Siena guide shows a product warning label "Located on the carriage" with the weight limit, the supplier's address and the model, and says "You may be asked for this number if you ring up your stairlift supplier"
(the model number). Harmar's manual has a page for the dealer's name, the date purchased and the "Serial # of the Lift" and says "For service or warranty work, your dealer will require the following information"
.
For a recall check, the serial number is what the records use. The CPSC page for the 2015 Acorn recall says the name "Acorn Superglide 120" and the serial numbers "are located on a silver label on the stair lift's carriage body cover and on the underside of the steel footrest."
For a battery, write down what is printed on the battery itself: voltage, amp-hours (Ah), chemistry (sealed lead acid, AGM, gel, lithium-ion, NiMH) and terminal type (F1, F2). The seller tiles we read print some of those details, and they differ between tiles that name the same lift, as the price section shows. In our view, photograph the battery label and the serial label before you call anyone. In our reading, reaching the batteries means opening the carriage or power pack, and Bruno's installation manual tells technicians to turn the carriage circuit breaker off and ground themselves before touching anything inside, so leave that to the dealer unless your own manual tells you how.
Stair lift battery: type, voltage and amp-hours, as printed
What kind of battery does a stair lift use, and what does the manual say about replacing it? Mobility Atlas read stairlift manuals and pages from Bruno, Harmar, Handicare, Stannah and Acorn on 19 November 2026. Bruno's SRE-3000 Elan installation manual lists "two (2) 12-volt sealed, maintenance-free batteries with 24-volt continuous-duty charger."
Bruno's SRE-2010 Elite manual prints no battery size. Stannah's UK 600 Siena guide prints the charger's "Output to stairlift: 24V DC 750mA."
Harmar's SL600 manual says "On average, replace batteries every 1-2 years based on usage"
and "Contact your local dealer for proper battery replacement."
None of these documents prints an amp-hour rating for the main batteries. Seller tiles naming Bruno (platform-lift tiles excluded) print 3Ah to 9Ah (the one Elan SRE-3000 tile prints 3Ah); in our view, read your old battery's label and ask the dealer before you buy. Handicare's 1100 and Freecurve warranties exclude batteries.
Harmar's SL600 owner's manual, in its section on maintenance and care, prints as a warning: "Non-compliant batteries may lead to product malfunction. Annual inspection is critical to identify battery condition."
Harmar's SL600 product page says the drive "provides up to 60 up and down cycles on batteries during a power outage"
, a maker claim for that model.
Seller tiles also list lithium-ion batteries. Of the 10 lithium tiles on Walmart's first page on 19 November 2026, 6 name the Acorn 180, 3 name only "Acorn Stairlift" and 1 names the "Superglide 130 T700", while other tiles on the same page sell 12V 7Ah batteries for an "Acorn 130 Straight" (chemistry not printed) and an SLA battery for an "Acorn Stairlift Superglide"
; one more tile offers a pair of 12 volt NiMH batteries for a "Bison 50". These are the sellers' claims; we did not find an Acorn document that prints the battery type, so we cannot confirm those tiles. Acorn's US FAQ says only "There are three main components to our lift. The motor, battery, and gear."
| Document | Main battery as printed | Charger as printed | Replacement interval as printed |
|---|---|---|---|
| Bruno SRE-3000 Elan installation manual (2019) | two 12-volt sealed, maintenance-free batteries | 24-volt continuous-duty charger; 24 VDC charger powered by 120-volt outlet | None printed |
| Bruno SRE-2010 Elite operator's manual (2019) | Not printed | 24VDC battery charger powered by 120V wall outlet; "maximum current (2.2A)" | None printed |
| Harmar SL600 owner's manual (2024) | Not printed | Power supply; charges within three feet of a landing | "every 1-2 years based on usage" |
| Stannah 600 Siena user guide (UK, 2013) | Not printed | Input 100 - 240V AC; output 24V DC 750mA | None printed for the lift; remote batteries "about one year" |
| Handicare Freecurve user manual (UK) | Not printed | Not printed | None printed; warranty excludes batteries |
| Acorn US pages and quick user guide | Not printed | Not printed | None printed |
How long a stair lift battery lasts, and what shortens it
Bruno's Elite manual says "Failure to keep the batteries charged, or allowing them to fully discharge, will significantly shorten the life of the batteries."
For best service life it says "Keep the battery charger plugged into a live outlet at all times."
On the Elite, the manual says "The batteries are charging whenever the carriage is at any location on the rail."
That is a design detail of that model; the Harmar and Handicare manuals describe charging at set points.
Harmar's SL600 manual says "Automatic charging occurs when the lift stops within three (3') feet at an upper or lower landing,"
"Keep the power supply plugged in continuously, and the lift can be left on charge indefinitely,"
and that "The stairlift must be turned"
on for charging, because the batteries "do not charge when the lift is turned"
off. Acorn's quick user guide says "IMPORTANT - THE SWITCH SHOULD REMAIN ON WHILE THE LIFT IS PARKED ON A CHARGE POINT."
and "It is important that the stairlift is moved to the nearest charge point to ensure battery drain does not occur,"
in its section for lifts with a hinged rail. Handicare's Freecurve manual says "The lift does not work if the batteries are flat,"
and in its reminders, "Never remove the lift plug from the wall socket."
On the Bruno Elite, the manual ties weak batteries to a slow lift: "A discharged battery will cause the carriage to move more slowly until the voltage drops to the point where the controller will shut off. If this should occur, pause for a moment, then run the carriage down to exit the seat. Partially charged batteries will run the carriage down, but not up. Contact your Bruno dealer to have the unit serviced."
The Bruno Elan installation manual tells the dealer that "Battery voltage should fall within the range of 16-28 VDC."
That is a dealer test, not an owner task.
Going away: Bruno's Elite manual says to turn off the circuit breaker, turn off the charger and unplug it, and that "The batteries may require recharging before normal use if the elevator remained in the OFF position for an extended period of time."
Stannah's UK guide says to switch off "both the master power switch and the wall switch"
for a long absence, which "will ensure that the batteries will still be charged when you return."
The two makers give different steps for the same situation; in our view, follow the manual for your own lift.
Power cuts: Bruno's Elite manual says the lift "will continue to operate for some time during a power outage,"
depending on battery condition, the length of the stairs and the rider's weight, and that "Only in the event of a prolonged power outage (more than one hour) will it be necessary to turn the power off (circuit breaker switch on the carriage) and turn off or unplug the charger from the wall outlet to conserve battery charge."
What to do if a lift stops part way with someone on it is in the stairlift guide.
Chargers, charging strips and charging stations
In our reading of the Bruno and Harmar documents, the charger turns wall power into low-voltage DC and feeds it to the carriage through contacts on the rail. Bruno's Elan installation manual describes "bronze charge strips" slid into a carrier on the back of the rail, with "charge contact" pieces at the ends and a "slow down (communications) strip"
. Its caution says "WEAR PROTECTIVE GLOVES AND EYEWEAR WHEN CUTTING OR HANDLING RAIL ENDS AND INSERTING BRONZE CHARGE STRIPS INTO CARRIER"
and "Sharp edges of the metal may cut bare hands."
In our reading, charge strips are a dealer part, fitted during installation.
Bruno's Elite troubleshooting page says "Do not use outlets which are controlled by a wall switch."
The one charger repair an owner manual describes
Bruno's Elite manual, in its battery charger section, says "If the charger is subject to a power line surge, the AC input fuse may blow."
Its steps: "Turn OFF the battery charger power switch,"
"Remove power cord from wall outlet,"
"Twist the fuseholder cap and pull out to remove the fuse,"
and "Replace with the same size and type fuse: (Bussmann GMD-2A or equivalent) 2A, Slo-Blow, 5 x 20mm."
That is the charger part replacement the Elite manual describes for the owner. If a new fuse blows again, in our view stop and call the dealer.
Reading the charger lights
| Bruno document | Light pattern as printed | What it says it means |
|---|---|---|
| Elite operator's manual, page 14 | Red on, yellow on, green off, blue off | charger delivering maximum current (2.2A); the next row prints the same pattern for "charger at maximum voltage; current continues to drop" |
| Elite operator's manual, page 14 | Red on, yellow off, green on, blue off | batteries fully charged; yellow LED occasionally turns off |
| Elan installation manual, page 39 | red (flashing) | defective batteries in unit; remedy: test batteries for damage or sulfation (load test) |
| Elan installation manual, page 39 | green (flashing) | reverse polarity connection to unit; check wiring to rail charge strips |
The Elite table has more rows than we show, and the PDF text is hard to read column by column, so check it against the printed page in your manual before you act on a light pattern. A defective battery, sulfation or reversed charge strips are dealer jobs in both Bruno documents.
Harmar's SL600 manual says a light on the chassis is "solid green" when the battery is fully charged and "solid amber" while charging, and that a flashing amber light with "an intermittent beep for 30 seconds indicates the lift has been stopped off the charge strip stations. This repeats every 5 minutes until the lift is returned to the charge strip stations."
It also says that if the lift is parked at the charge station and beeping intermittently, "it could be because the power supply is not connected to the AC power."
Handicare's Freecurve manual says that if the lift is not correctly at a charge point, "the lift beeps for three minutes and the LED in the armrest flashes."
In our view, match a replacement charger's output voltage, plug and the maker's number printed on your old charger, and have the dealer confirm it; the price section lists three on Zoro.
Stairlift remote and call stations
How do you replace a stairlift remote or its batteries? Mobility Atlas read the remote sections of Bruno, Stannah, Harmar and Handicare documents on 19 November 2026. Bruno's SRE-2010 Elite manual says to remove the access panel on the back of the transmitter: "Two AA alkaline batteries required. Change batteries annually."
Stannah's UK 600 Siena guide says "Each remote calling control takes three AA batteries"
and that they "will last about one year with average use."
Handicare's Freecurve manual says of flat remote batteries: "replace the batteries in the remote control."
For a new remote, Bruno's Elan installation manual, a dealer document, says remotes are reprogrammed when they "need to be replaced", using dip switches in the remote and a LEARN/ERASE button on the carriage circuit board. In our reading, that makes a replacement Bruno remote a dealer visit. Remote batteries are excluded from the Bruno and Handicare warranties we read.
The documents differ on remotes. Bruno's Elite manual says "The transmitters are NOT designed to move a seat with a person on board,"
and "While riding in the seat, ALWAYS operate the elevator using the rocker switch on the armrest."
Harmar's SL600 manual describes the call/send units for sending the unit "up or down (unoccupied)", but also allows remote operation for a seated person: "If you are operating the lift on behalf of another person, ensure they are securely seated with the seat belt fastened before initiating the remote operation."
It adds that "The remote controls are disabled for 15-seconds after the armrest control is used."
Stannah's guide, as a safety notice: "Make sure no one else is using the stairlift before you call it using the wall mounted calling controls."
Infrared or radio: why a remote stops working
The documents name two kinds of remote. Bruno's Elite manual says the transmitter "uses infrared (IR) communications"
with receivers "mounted on both sides of the SRE-2010 carriage"
. Its advice: "DO NOT mount the transmitters behind an obstacle such as a rail post or around a corner,"
"DO NOT allow direct sunlight to shine on the receivers,"
and "Depleted or nearly-depleted batteries alter the effective range of the transmitter."
It warns against cleaning the lens with "polishes or cleaning products containing wax."
The Handicare 1100 manual also says its wall mounted remotes "operate on a infrared frequency"
. The Freecurve manual's pictures label the remote "868MHz", a radio band, and its text says Handicare does not accept responsibility for the wall buttons failing "due to interference by a source outside this stairlift."
In our view, tell a seller whether your remote is infrared or radio, its part number and the lift serial number. Bruno's Elan manual lists four dip switch settings and says the factory default is "1 up, 2 down".
Part numbers printed for Bruno remotes
The exploded view at the back of Bruno's Elan installation manual, sheet "REV. 11 (6180)(3/17/17)", lists for the SRE-3000 Elan "TMR-00004 IR TRANSMITTER ASSEMBLY W/ 2 'AA' BATTERIES"
(quantity 2) and "SRE-00963A IR TRANSMITTER/BRACKET/HDWR (KEYED)(ROHS)"
. The customer education page names an optional wall bracket kit, "TMR-00005". Those numbers are printed for the SRE-3000 on that sheet; we did not find a Bruno document that ties them to other models.
Error codes, beeps and lights, as the manuals print them
In our view, fault codes, lights and beeps belong to the model, so use the table in your own manual.
Bruno SRE-2010 Elite: diagnostic codes under the seat
| Code | Meaning as printed |
|---|---|
| A2 | Seat in UP Position (Seat Fold Switch Closed) |
| A3 | Seat Out of Riding Position (Swivel Limit Open) |
| A7 | Seat or Footrest Jammed (Actuator Stalled) |
| C1 | Charging |
| C2 | Off Charge (Running) |
| C4 | Parked and Charger Not Detected |
| C5 | Battery Voltage Critical (Charge Immediately) |
| C6 | Battery Voltage Low |
| L1 | Seat Safety Switch Open |
| L2 | Up Limit Switch Open |
| L3 | Down Limit Switch Open |
| L6 | Mid-Rail Park Active |
| L8 | Soft Stop Switch |
Source: Bruno SRE-2010 operator's manual, page 13. C4, C5 and C6 point to the charger or batteries; A3 and L1 to the seat swivel.
Harmar Pinnacle SL600: lights and beeps
Harmar's manual says "A green light indicates the lift is in operating mode,"
"An amber light indicates the lift is touching an obstruction and may be operated only in the direction away from the obstruction,"
and "A red light indicates a problem that may require a service call."
If the light stays red after turning the lift off and on again, the manual says to "contact your local dealer and describe the problem."
Its major-fault table counts beeps: 1 for "Runaway", 2 for "No Power", and 3 to 8 for pairs of "Conflicting switches" (footrest, obstruction and stop switches). A "Single long beep" is a minor fault that "Will reset once fault is cleared"
: seat swiveled out of position, edge safety, footrest, current overload or "A low battery voltage condition"
.
Bruno SRE-3000 Elan: the multi-user beep
Bruno's Elan installation manual says units ship in multi-user mode, in which "when seat is swiveled at top of rail, unit beeps once every three (3) seconds"
, and that a dealer can switch to single-user mode with a jumper inside the carriage. In our reading, a beep every three seconds at the top on that model is this setting, not a fault.
Handicare Freecurve and Stannah 600
Handicare's Freecurve manual links each problem to a cause: a lift that travels one way only with a flashing LED has "an obstacle between the lift and the stairs"
; a lift that will not move may have the seat "not locked" in a swiveled position or the emergency stop pressed (LED flashing), or an armrest not folded down (LED lit). Stannah's UK 600 Siena guide prints eight display codes, from "-/1" to "9/F", with reasons such as "Charging / battery fault."
and "Service Engineer required."
The PDF text does not keep the rows of that table together, so read the code against the printed page in your guide.
Acorn's quick user guide prints no codes; it says "BOTH ARMS MUST BE COMPLETELY DOWN FOR THE STAIRLIFT TO OPERATE."
In our view, a code that comes back after a reset is a reason to call the dealer, not to order a part by guesswork.
Seat, swivel, armrest and footrest parts
In our reading of the Bruno and Harmar manuals, the seat assembly carries the swivel lock, the seat switches and, as an option, a power swivel motor. The Bruno, Harmar and Acorn documents say the lift will not run unless the seat is locked in the riding position. Bruno's Elite manual: "A safety switch prevents operation of the SRE-2010 unless the seat is locked in position at right angles to the rail"
. Harmar's SL600 manual: "An interlock on the swivel seat prevents the lift from being operated unless the seat is in its normal, locked position."
Acorn's quick user guide: "The seat must be swiveled back into position to operate."
Before you suspect a broken part, the Bruno Elan installation manual's troubleshooting table answers a common worry: a unit that "WILL NOT OPERATE UNLESS SEAT IS POSITIONED SO IT FACES OPEN SIDE OF STAIRS"
is "correct lift operation." Harmar's manual says that if the seat is not fully locked, "the seat swivel interlock alarm will sound,"
and users "may need to ensure the swivel levers are fully engaged in the locked position by wiggling in the seat or re-depressing the levers"
.
Power swivel and power footrest
Power options add small motors and fuses. Harmar's SL600 manual says that if the user keeps pressing the control for more than 5 seconds after the power swivel stops, "the resettable fuse will trip to safeguard the rotation motor,"
and users "must wait for approximately 1 minute for the fuse to reset"
. Its troubleshooting page says the fuse "needs to rest for 2-minutes"
. The two times differ on two pages of one manual; in our view, wait the longer one. For the power footrest, Harmar says "DO NOT move the footrest manually or by stepping on it. This may lead to damage and void the warranty,"
and, in its fault section, "DO NOT use the lift if the footrest is not fully lowering."
Bruno's Elite manual says of its power footrest: "Do not try to manually raise or lower the footrest. Always raise/lower the footrest by raising/lowering the seat. Failure to follow this instruction could damage the unit."
If a jam is not cleared by moving the seat, "contact a Bruno Service Representative."
Part numbers printed for the Bruno Elan seat and footrest
| Part as printed | Number | Document |
|---|---|---|
| SEAT ASSEMBLY | SRE-30102 | Bruno SRE-3000 exploded view, REV. 11 (3/17/17) |
| FOOTREST ASSEMBLY | SRE-30100 | same sheet |
| POWER FOOTREST ASSEMBLY (optional) | SRE-30212 | same sheet |
| POWER SWIVEL ASS'Y - LH / - RH (optional) | SRE-30405L / SRE-30405R | same sheet |
| FOOTREST/SEAT INSTALLATION KIT | SRE-K-3011 | same sheet |
| FOOTREST FOLD SWITCH KIT (ARMREST MOUNT) (optional) | SRE-K-3027 | same sheet |
| CARRIAGE ASSEMBLY | SRE-30099 | same sheet |
Left and right matter: Bruno's sheet gives separate numbers for left-hand and right-hand power swivels, and its installation manual says the SRE-3000 "is shipped from the factory ready for a left-hand installation"
. The side is named "as viewed from bottom of the stairs"
in the same manual. Handicare's Freecurve manual prints a page of part numbers on a drawing without labels; we could not tie them to parts, so we do not list them.
Bruno's Elan manual also says "If it becomes necessary to replace any bolts or fasteners, use only metric GRADE 10 9 (hardened steel) hardware"
and that "Bolts without grade markings on the head are not strong enough to be safely used in this application."
In our view, a seat that wobbles, leans or creaks is a dealer call before the next ride, for the reasons in the recall section below.
Safety edges, obstruction sensors and seat belts
Harmar's manual describes safety edges as spring-loaded sensors on the carriage and footrest that stop the lift when they touch something. Harmar's SL600 manual: "There are spring loaded sensors on the top and bottom of the carriage, and the front, back and underside of the footrest. If any of these edges touches an obstruction, the lift will halt immediately, and the armrest LED indicator light will turn orange. The lift may only be driven away from the obstruction."
Stannah's UK guide says the safety edges "stop the stairlift if they come into contact with any obstacles. This stops anything from becoming trapped while the stairlift is being used."
A lift that stops for no visible reason can have an edge that stays pressed. Bruno's Elan installation manual tells the dealer to check that the "Sliding safety tray below footrest should slide freely and should not stick in a position which would depress one of the safety switches,"
and to check that the "footrest safety tray is not dragging on stair nosing or hitting debris on stairs."
For owners, Bruno's Elite manual asks: "Is there an obstruction on the stairway that the footrest is contacting?"
and the same for the "carriage safety panels".
Do not disable a safety edge or switch: Harmar's manual says "Do not disable any safety equipment or switches supplied with this lift."
Handicare's Freecurve manual, in its section for the installer on safety devices, says "The product must never be used if the safety devices are incomplete or absent, or have been put out of action or are defective."
Handicare's 1100 manual says "Don’t use the lift if parts are defective or missing (e.g. track end caps of the slidetrack)."
and "To avoid accidents repairs and preventive maintenance should only be carried out by engineers qualified to do so."
In our reading of the two Handicare manuals, a cracked edge cover or a sensor that sticks is a reason to stop using the lift and call the supplier, not a part to order and fit yourself.
Seat belts
Harmar's SL600 manual says "A retractable seat belt is provided and must be secured around the user to prevent an inadvertent fall."
Acorn's quick user guide says "IMPORTANT - SEAT BELT MUST BE WORN DURING OPERATION."
Bruno's Elite manual says "Fasten your positioning belt before operating the stairlift."
Handicare's manuals say "Always use the safety belt"
and "never stand on the stairlift"
. Stannah's UK guide offers an optional "Immobiliser seatbelt", with which "your stairlift will not start until you have put your seatbelt on."
None of the manuals we read prints a part number or a replacement interval for the belt. In our view, a belt with a frayed strap, a cracked buckle or a retractor that does not pull back is a dealer repair before the next ride, and the replacement should be the maker's belt for that seat
Rails, gear racks, folding rails and keys
The rail is the part cut to your stairs. Bruno's Elan installation manual describes a "vertical aluminum extrusion with integral drive gear rack"
, and its exploded view prints the rail numbers by length and type:
| Rail as printed on the Bruno SRE-3000 sheet | Number(s) |
|---|---|
| 16' standard, left or right | (2) SRE-30094 |
| 20' standard, left or right | (2) SRE-30095 |
| 16' folding, left / right | (1) SRE-30379L or SRE-30379R and (1) SRE-30094 |
| 18' folding, left / right | (1) SRE-30379L or SRE-30379R and (1) SRE-30095 |
| 16' power folding, left / right | (1) SRE-30372L or SRE-30372R and (1) SRE-30094 |
| 18' power folding, left / right | (1) SRE-30372L or SRE-30372R and (1) SRE-30095 |
| Rail installation kits | SRE-K-3001 (16'), SRE-K-3002 (20'), SRE-K-3050 (folding rails) |
The same manual says never to cut a rail shorter than 24 inches (610 mm), or a folding rail assembly shorter than 75 inches (1905mm). Acorn's US FAQ says "Most Acorn stairlifts can be shortened, but this must be carried out by an Acorn approved Engineer"
.
Grease or no grease
Maintenance of the rack differs by maker. Bruno's Elan installation manual says "Apply a thin layer of white lithium grease (provided) on gear rack ONLY,"
and its troubleshooting table suggests "a small amount of grease to gear rack only"
for a rough ride. Bruno's Elite manual tells owners to "Keep the rail channel clean and free of debris"
and to have the lift "examined, cleaned and lubricated"
at least once a year by "a qualified, authorized Bruno service technician."
Harmar's SL600 manual says "The drive system does not use grease or lubricants, and no adjustments should be necessary."
Handicare's 1100 manual says "The use of lubricant on the rail is also not permitted."
Stannah's guide says to clean the rail with a damp cloth and not to use solvents, waxes or sprays "without checking with your stairlift supplier first."
In our view, grease that suits one lift is forbidden on another, so check your own manual.
Folding and hinged rails
A folding rail adds a hinge, a motor on powered versions, and a pinch point. Bruno's Elite manual prints, under "PINCH POINT", "Make sure the areas above and below the folding rail are clear before operating the folding rail. Keep children and pets at a safe distance. Failure to observe this warning could result in injury or damage to equipment."
For the manual folding rail it says "Damage to the carriage WILL occur if the carriage is below the mid-park position when the rail is folded up."
For the power folding rail it says "Do not attempt to manually fold the power rail,"
except, marked as for an emergency only, when the rail cannot be moved with the armrest switch or the transmitter: then "switch the disable switch to OFF. Manually, and GENTLY, raise or lower the rail,"
because "Lifting the rail in a quick, sudden motion may result in damage to the folding rail gearbox."
Its Elan installation manual adds: "If power folding rail stops, then slightly reverses direction, and there are NO OBSTRUCTIONS, call BrunoTechnical Service"
.
Keys and key switches
Keys stop other people, including children, from using the lift. Handicare's 1100 manual says "Remove the key after use to prevent unauthorised use."
Stannah's guide says "you can remove the power key to stop others from using your stairlift."
Harmar lists a key lock as an option on the SL600 page. Bruno's Elan installation manual tells the installer "Do NOT lose carriage key attached to cable tie."
None of the documents prints a key part number. In our view, ask the dealer for a spare key at handover and keep it with the manual.
Who may replace what, according to the documents
The documents split the work clearly. Owners clean, charge, keep the lift parked on charge, change remote batteries and, on the Bruno Elite, a charger fuse. Dealers do the rest. Here are the lines, quoted, with their documents.
| Document | Owner tasks it describes | Dealer or engineer line, as printed |
|---|---|---|
| Bruno SRE-2010 Elite operator's manual | Remote AA batteries; charger fuse; cleaning the rail channel; keeping charger plugged in | "contact an authorized Bruno dealer to perform all required service, repair and maintenance operations." |
| Bruno Gold warranty (rev. 04-18) | Maintenance "as called for in the Operator's Manual" | "all maintenance and repair work on the Bruno Stairlift, [...] must be performed by a Bruno Authorized Dealer." |
| Harmar SL600 owner's manual | Cleaning; keeping the power supply plugged in; manual override in a lift failure | "Do not attempt to service the lift yourself."; "Contact your local dealer for proper battery replacement." |
| Handicare 1100 user manual | Cleaning; removing the key | "Installation and servicing should only be carried out by dealers or installers/service engineers authorised by the manufacturer" |
| Handicare Freecurve user manual | Replacing remote batteries; parking on charge | "repairs and preventive maintenance must only be carried out by engineers qualified to do so." |
| Stannah 600 Siena user guide (UK) | Remote batteries; cleaning; emergency drive | Safety page: "Never attempt to dismantle the stairlift." |
| Acorn US servicing page | Not described | Lifetime motor and gearbox cover needs the lift "serviced annually by an Acorn engineer" |
Two of these lines carry warranty consequences. Bruno's Elite manual says "The warranty for the SRE-2010 Stairlift is rendered null and void if the unit is installed or maintained by anyone other than an authorized Bruno dealer."
Harmar's SL600 manual says "Any alterations to the equipment without written authorization by the manufacturer is prohibited and will void the warranty."
Handicare's 1100 manual says "The carrying out of alterations to the product is not permitted and doing so will invalidate the warranty."
Manual override is a deeper task that the Harmar and Stannah owner documents describe, for an emergency. Harmar's SL600 manual says that "In the event of a lift failure where the operator is unable to exit the lift on the stairway,"
a 1/4 inch or 7mm socket and wrench, "depending on your model," can be used to lower or raise the lift after turning it off. Stannah's UK guide describes an "emergency drive" behind an access door, for a lift that has stopped and "is causing an obstruction"
. These steps move a stuck lift; they do not repair it. Harmar's override steps start with "Confirm that the operator cannot exit the lift on the stairway and follow the instructions on the bottom safety flap of the lift."
Stannah's HELP page says "If the checklist doesn't help you to solve the problem, contact your stairlift supplier."
In our view, call the dealer or supplier after any emergency move.
Whether a stairlift still suits the person who rides it, and how they get on and off safely, is a question for an occupational therapist or physical therapist, not for a parts seller. Bruno's Elite manual also recommends that non-ambulatory users carry "a cellular or cordless telephone or an emergency communication device when riding the stairlift while alone in the house."
Warranty by document: motor and gearbox, parts, batteries, labor
Which stairlift parts are under warranty, and for how long? Mobility Atlas read the warranty text in Bruno's and Harmar's manuals, Handicare's two user manuals and Acorn's US pages on 19 November 2026. The Bruno Gold warranty (rev. 04-18) covers "Major Components, including the motor, gearbox, drivetrain, and rail system"
for the lifetime of the lift while the original purchaser owns it, other parts for "two (2) years after the date of installation"
, and labor for "the first thirty (30) days after installation"
. Harmar's SL600 manual covers the motor, gearbox, rail, worm gear and gear rack for life, "other parts and electrical components"
for three years, and says "Supplied batteries are limited to one (1) year from the date of retail purchase."
Handicare's manuals give 24 months "(excluding batteries)". Acorn's page says "Includes 12-months manufacturer guarantee"
; another gives motor and gearbox life if the lift is "serviced annually by an Acorn engineer"
. In our view, ask for the written terms for your serial number.
| Document | Motor, gearbox, rail | Other parts | Main batteries | Labor | Conditions as printed |
|---|---|---|---|---|---|
| Bruno Gold warranty terms, rev. 04-18 (in the Elite and Elan manuals) | Lifetime, original purchaser | 2 years from installation | Not named; "Consumable items such as remote batteries"excluded | 30 days | Installed and maintained by a Bruno Authorized Dealer; starts at installation, "no later than 14 months after it was shipped from the factory" |
| Harmar SL600 owner's manual (2024) | Lifetime: motor, gearbox, rail, worm gear, gear rack | 3 years | 1 year | "Harmar will not be charged for labor" | Return the warranty form within ten days (the manual says of purchase on page 5, of installation on pages 20 and 21); SL600s outdoors or in commercial buildings not covered |
| Harmar SL600 product page | "Lifetime motor warranty – any unit post 9/2018"; "Gear rack: 10 year" | Not printed | "Battery: 1 year" | Not printed | Page says "Rated commerical and residential" |
| Handicare 1100 and Freecurve (UK) user manuals | 24 months | 24 months | Excluded | "repaired free of charge" within 24 months of the purchase date (labor not named separately) | Remote batteries, wear, overloading and misuse excluded |
| Acorn US stairlifts page and servicing page | Lifetime motor and gearbox, original consumer purchaser | "12-months manufacturer guarantee" | Not printed | Extended warranty "covers the cost of all callouts, parts and labor" | Annual service by an Acorn engineer |
The Harmar documents disagree on two points. The 2024 owner's manual gives the gear rack and rail a lifetime term; the SL600 page gives the gear rack 10 years. The manual says SL600s in commercial buildings "are not covered and are not approved for commercial use"
; the page says the lift is rated commercial and residential. Until Harmar or the dealer confirms in writing, plan on the shorter gear rack term and on no cover for commercial use.
Bruno's Elan page, read on 19 November 2026, says "Limited Lifetime Warranty"
; its "Warranty Details" link opens a viewer whose text we could not read, so the terms above are those printed in the 2019 manuals. Stannah's 2013 UK guide prints no warranty terms; Stannah's UK and US warranty pages are compared in our Stannah guide.
Bruno's warranty excludes "Reasonable wear and tear" and "All labor by a Bruno Authorized Dealer after the first thirty (30) days since installation."
Harmar's excludes maintenance and adjustments and says defective parts "must be returned, prepaid, to Harmar for inspection before credit, repair, or replacement, at Harmar's discretion."
Handicare's Freecurve manual lists as "Excluded from guarantee: damage caused by normal wear and tear, overloading or misuse, the replacement of batteries in the remote control."
In our reading of these documents, main batteries are covered for one year by Harmar's manual and not at all by the two Handicare manuals; other parts run two years under Bruno's warranty, three under Harmar's manual and 24 months under Handicare's; labor after 30 days (Bruno) or at any time (Harmar) is not covered.
Stairlift recalls: what the FDA and CPSC records show
Stairlift recalls appear in two US databases. The FDA's recall data lists stairlifts under product code PCD, the code Harmar's SL600 page prints for its lift; a CPSC database search by the product name "stair lift" returned one recall, and a search for "stairlift" returned none. On 19 November 2026 the openFDA recall data (last updated 2026-11-14) held 3 records under code PCD. A word search of product descriptions for "stairlift" or "stair lift" found 6 records across product codes ILK, KNO, PCD, initiated from 2012-08-06 to 2020-03-02. The openFDA enforcement data returned no record under code PCD.
| Recall | Product as stored | Initiated | Status as stored | Quantity as stored | Reason (summary of the stored text) |
|---|---|---|---|---|---|
| Z-0681-2022 (FDA, code PCD) | Acorn 130, Brooks 130, Acorn 180 and Acorn Outdoor Stairlift | 2016-04-20 | Open, Classified | 26,428 | seats "did not consistently have the adequate strength required to support the customers weight with continued use" |
| Z-1530-2016 (FDA, code PCD) | Acorn 180 Curved Stairlift | 2016-02-17 | Terminated 2019-01-29 | 1,290 USA and 9,607 Foreign | aluminum rivets holding the base squab "were seen to elongate and subsequently break" |
| Z-2060-2017 (FDA, code PCD) | Savaria SL-1000 Stairlift | 2017-04-12 | Terminated 2018-03-05 | 1425 in the United States, 734 in Canada | controller and motor feedback damaging a component on the control board, "starting a fire" |
| Z-1882-2017 (FDA, code ILK) | Savaria Stairfriend curved stair lift | 2017-04-12 | Terminated 2017-10-16 | 226 | "poor quality of welding holding the seat post" |
| Z-0557-2013 (FDA, code ILK) | ThyssenKrupp Accessibility LEVANT Stairlift | 2012-08-06 | Terminated 2014-01-29 | 5,413 stairlifts | seat could break if the unbuckled seat belt is trapped under the folding seat |
| Z-1632-2020 (FDA, code KNO) | Merits E604 Pilot Navigator Stairlift, "To transport patients up stairs" | 2020-03-02 | Terminated 2023-09-18 | 82 units | "Pinion gear may disengage from track allowing lift to slip or jolt." |
| CPSC 15-189 | Acorn Superglide 120 and versions, made March 2007 to March 2011 | Recall date July 21, 2015 | Remedy: Repair | About 34,500 | "The stair lift's seat post can separate from the main seat support, posing a fall hazard." |
The Merits E604 record, under product code KNO, describes it only as a device "To transport patients up stairs"
; we did not read what kind of device it is. It appears because its description contains the word "Stairlift". Z-0681-2022 was initiated on 2016-04-20 and was still stored as "Open, Classified" when we read it.
Several of these recalls are about seat parts, which matters when you order a replacement seat, seat base or "squab" for an older Acorn. The FDA record for Z-0681-2022 says the firm phoned owners to say "they are going to replace one of the components on the stairlift,"
and its mailed notice said "the seat base could weaken over time causing a remote possibility the seat base could crack or separate from the seat assembly."
The CPSC page for the Superglide 120 says "Consumers should immediately contact Acorn for a free in-home repair,"
and "If a consumer is able to use the stairs safely, then he or she should not use the lift until it is repaired."
It reports that Acorn "received two reports of incidents of the seat post separating from the main seat support and resulted in deaths in the United Kingdom. There have been no reports of incidents or injuries in the United States."
In our view, if you own an older Acorn, Brooks, Savaria or ThyssenKrupp lift, check the serial number with the maker before you buy any seat part, and use the recall remedy, not a used part.
A recall record counts lifts, not failures, and the CPSC and FDA records are separate lists. For how to read FDA device reports about stairlifts, see the stairlift guide.
What stair lift replacement parts cost: two US sellers on 19 November 2026
We read the first results page of three searches. Prices are US dollars as printed on the tiles, before tax and shipping, and change from day to day. The tiles are sellers' listings of replacement batteries and chargers from battery brands (Mighty Max, AJC under the Battery Clerk and BSC Preferred names, Liftcharger and others), not parts sold by Bruno, Harmar, Handicare, Stannah or Acorn. A tile that names a stairlift is the seller's claim of fit; we did not find a maker document that confirms any of them.
Zoro, "stairlift battery"
Zoro printed "148 results"; the first page loaded 36 tiles, and we read those 36. Counting rule: we kept the 35 battery tiles, dropped the 7 whose titles name a platform lift ("Vertical Platform", "Lifting Platform" or "Backpacker"), and split the remaining 28 stairlift battery tiles by whether the title prints a pack count. One tile was a charger.
| Group | Tiles | Lowest as printed | Highest as printed |
|---|---|---|---|
| Stairlift batteries, no pack count in the title | 16 | $19.99 /ea (Mighty Max 12V 7Ah tile naming Bruno Electra-Ride) | $34.29 /ea (AJC Acorn 130 Outdoor Stairlift Replacement Battery 7Ah, 12V, F1) |
| Stairlift batteries, packs of 2 to 10 | 12 | $37.99 /ea (three 2 Pack tiles) | $214.99 "/pk of 10, $21.50/ea" (12V 8Ah Bruno Electra-Ride, 10PK) |
On Zoro's page, all 16 no-pack tiles print 12V; 14 print 7Ah and 2 print 8Ah. AJC tiles name the lift: "AJC Bruno Indoor Straight Stairlift Replacement Battery 7Ah, 12V, F1"
at $33.45, the Bruno indoor curved, outdoor straight and outdoor curved tiles at $33.99 each, and "AJC Harmar Pinnacle Stairlift Replacement Battery 7Ah, 12V, F1"
at $33.99. Zoro's unit labels need care: the 10 pack of 7Ah Electra-Ride batteries printed $159.99 /ea, while the 10 pack of 8Ah printed $214.99 /pk of 10, $21.50/ea. In our view, ask the seller what one order line contains before you buy.
Zoro, "stairlift charger"
Zoro's page printed "8 results" and showed all 8. 3 were Liftcharger chargers from $80.89 to $94.59: "Bruno Elan Stairlift Charger for SRE-3000 replace OEM-2401, OEM-2401B, BCR-24022"
at $82.69, "Harmar Stair Lift Adapter Battery Charger for Pinache SL300 SL600 Stairlift"
at $80.89 (spelled as printed), and "Power Adapter/Battery Charger for Bruno Stairlifts, Replace OEM-2402, BCR-24018, BCR-24024"
at $94.59. 4 were Mighty Max battery-and-charger sets from $37.99 to $56.25, three naming an Acorn stairlift and one the Bruno LT SRE-2750; their titles name a 12V charger. In our reading these chargers are for the loose 12 volt battery: the two Bruno manuals we read (SRE-2010 and SRE-3000) print a 24 volt charger for the lift, and we read no Acorn or SRE-2750 document that prints the charger. The eighth tile, a "Stair Climber Charger" at $329.99, is for a different device.
Walmart.com, "stairlift battery"
Walmart printed "107 Results" over several pages; we read page 1, which carried 50 priced tiles in the results grid plus a 3-tile sponsored carousel. Counting rule: we kept tiles whose title names a stairlift or a stairlift model (stairlift, stair lift, stairway, Electra-Ride, Superglide, Bruno Elan or Acorn), and dropped sponsored tiles and the 3 platform lift tiles; that dropped 16 tiles, including car battery chargers and a vacuum battery, and left 34.
| Group (Walmart page 1) | Tiles | Lowest as printed | Highest as printed |
|---|---|---|---|
| Lead-acid or unstated, no pack count in the title | 18 | $18.99 (12V 3AH SLA Replacement Battery for Bruno Elan SRE-3000 Medical Lift) | $117.99 (Bright Way Replacement Battery for Stairlift SLA Sealed Lead Acid Rechargeable Battery 12V 55AH NB) |
| Lead-acid, packs or with a charger | 5 | $39.98 | $198.99 (12V 9Ah for Acorn, 10 Pack) |
| Lithium-ion, 14.4 or 14.8 volt, for Acorn | 10 | $118.00 (1pcs T565 for Acorn 180) | $239.00 (four tiles) |
| NiMH | 1 | $298.00 | (2pcs Bison 50) |
Walmart's tiles print no Walmart item number; a few titles include a battery maker's number, such as UB1270 or ES7-12. The battery size printed for Bruno lifts varies across tiles. On Walmart, stairlift tiles that name Bruno (platform-lift tiles excluded) print 3, 7, 7.5, 8 and 9 amp-hours, and the $18.99 tile is a "12V 3AH SLA Replacement Battery for Bruno Elan SRE-3000 Medical Lift". On Zoro, tiles naming Bruno print 7 or 8 amp-hours. Bruno's Elan manual prints no amp-hour figure, so the tiles cannot settle it: read the old battery's label and ask the dealer.
Both sellers list an AJC 12V 7Ah battery naming the Acorn 120 Superglide: $33.99 at Zoro and $29.49 at Walmart, a difference of $4.50. The titles differ and Walmart's tile prints no part number, so we cannot confirm it is the same item. The Acorn Superglide 120 is the model in CPSC recall 15-189; see the recall section before you work on one.
We found no seller page with a US dollar price for stairlift remotes, call stations, seat belts, safety edges, seats or rails on the pages we could read. In our view, ask the dealer for a written price with the part number.
Maker parts, look-alike batteries and used parts
The documents give three reasons to start with the maker's part. First, Harmar's SL600 manual prints, as a warning, "Non-compliant batteries may lead to product malfunction."
Second, Handicare's Freecurve manual, in its installer section, says "Do not use defective parts; only use original parts."
Third, the Bruno and Harmar warranties are void or limited when someone other than the dealer works on the lift or alters it, as quoted above.
Seller tiles that say a charger "replace OEM-2401" or a battery is "Compatible With" a lift are the seller's statement. They are not the maker's part, and in our view they should be described to the dealer as a charger the seller lists as replacing "OEM-2401" (Zoro's tile does not say whose number that is), so the dealer can check the plug, voltage and output against your lift. In our view, a battery of the right voltage can still have the wrong terminal (the tiles print F1, F2 or NB) or a different chemistry, so match the old battery's label.
On 19 November 2026 an eBay search for "stairlift remote" printed "173 results"; its first page listed pre-owned Bruno, Harmar, Acorn and Handicare remotes, priced in Thai baht in our browser, so we did not use the prices. In our view, buy a used remote when the dealer has confirmed the model and can program it to your lift, not before. Bruno's Elan manual says the "Operating channel of the two (2) remote transmitters included with the SRE-3000 is pre-set at the Bruno factory"
and lists "remotes need to be replaced"
as a reason to reprogram.
Medicare, Medicaid and other payers
We did not read Medicare, Medicaid or VA rules for this guide. What Medicare and other US programs say about stairlifts is in our stairlift guide and Stannah guide. In our view, ask the plan about repair parts.
Three traps
- Buying a battery by the lift's name alone. Stairlift tiles that name Bruno (platform-lift tiles excluded) printed 3, 7, 7.5, 8 and 9 amp-hours on one Walmart page, and Bruno's manuals print no amp-hour figure. Match the label on the old battery, the terminal type and the dealer's advice, and remember Harmar's warning that
"Non-compliant batteries may lead to product malfunction."
- Treating a beep as a broken part. On the Bruno Elan, a beep every three seconds at the top is the multi-user setting; on the Harmar SL600, flashing amber with beeps means the lift is off its charge strip; on the Handicare Freecurve, three minutes of beeping means the lift is not on a charge point. In our view, park the lift on charge and read your manual before you order anything.
- Fixing a part that should stop the lift. A stuck safety edge, a seat that will not lock or a power footrest that will not lower are stop signals in these manuals: in its power footrest faults, Harmar's SL600 manual says
"DO NOT use the lift if the footrest is not fully lowering,"
and Handicare's Freecurve manual says"Do not use the lift if a part is defective."
In our view, call the dealer instead of bypassing a switch.
Three composite scenarios
These are composite scenarios, not individual customers. Each uses the documents for that lift.
Scenario one: a Bruno Elite that runs slowly upstairs
An owner of a Bruno SRE-2010 Elite installed four years ago notices the lift slowing on the way up, and one evening it will go down but not up. Bruno's Elite manual says "Partially charged batteries will run the carriage down, but not up,"
and the next line is "Contact your Bruno dealer to have the unit serviced."
The underseat display shows C6, which the manual lists as "Battery Voltage Low". The owner stops using the lift, leaves it parked on charge with the charger in a live outlet not controlled by a wall switch, and calls the dealer that evening. The dealer tests and replaces the batteries; the owner pays for the batteries and the visit: the lift is past the two years the Bruno Gold warranty gives parts other than major components, and labor is covered only for the first 30 days. The owner also buys two AA batteries for each remote, as the manual says to change them annually.
Scenario two: a Harmar SL600 that beeps on the landing
A household with a Harmar Pinnacle SL600 bought three years ago hears an intermittent beep and sees a flashing amber light after someone sends the lift halfway down. Harmar's manual says this "indicates the lift has been stopped off the charge strip stations"
and recommends that "the lift be immediately moved to the charge strip station located at either end of the rail."
They send it to the landing with the call/send unit. A year later the lift stops on the stairs with a red light that stays red after a reset; the manual says to contact the local dealer. The dealer finds worn batteries; the manual says "On average, replace batteries every 1-2 years based on usage,"
and the warranty limits supplied batteries to one year from the date of retail purchase and says Harmar will not be charged for labor, so the household pays for both.
Scenario three: a Handicare 1100 with a missing end cap and a new creak
A household with a Handicare 1100 on a slidetrack notices a squeak from the carriage and that one track end cap has come off. Handicare's 1100 manual says "Report unusual noises, such as squeaking and creaking, to your supplier,"
and "Don’t use the lift if parts are defective or missing (e.g. track end caps of the slidetrack)."
So they stop using the lift, read the serial number from the label on the power pack under the seat, and call the supplier, because the manual says "To avoid accidents repairs and preventive maintenance should only be carried out by engineers qualified to do so."
The lift is 20 months old, inside the manual's 24 months for manufacturing and material defects, but the guarantee excludes batteries and damage "caused by normal wear and tear, overloading or misuse"
, so they ask the supplier in writing which parts of the visit are covered. An occupational therapist is checking transfers for the person who rides it; the 1100 manual gives a maximum load of 264 lbs on the slidetrack, lower than its 308 lbs and 286 lbs figures for the two incline ranges without the slidetrack, so the household plans on 264 lbs.
Questions to ask the dealer, the seller or the maker
- What is the exact model and serial number, and is there an open recall for it? (Check the FDA and CPSC records above.)
- Which battery does this lift take: voltage, amp-hours, chemistry, terminal and how many? Do you replace both batteries together?
- Is the part a maker part with its maker number, or a replacement sold as fitting? Will fitting it affect my warranty?
- For a remote: infrared or radio, which maker number, and will you program it to my lift?
- Is this repair covered by the maker's warranty, and does the warranty include labor? Ask for the warranty terms for my serial number in writing.
- For the seat, belt, footrest or safety edges: can I keep using the lift until you replace it? Please put that answer in writing.
Service intervals: Bruno's Elite manual and Stannah's guide say once a year, Harmar's says "An annual inspection is recommended,"
and Handicare's 1100 and Freecurve manuals say at least once a year, twice with more than two users (Freecurve: or more than two floors).
Sources and documents
How we checked: each page or PDF was saved as text with its address and read date, PDFs were extracted in the browser, and the counts, price ranges and the price difference were computed by script from the saved text. Part numbers and fit are given only as a maker document or a seller's tile prints them. We could not read Bruno's owner's manual search tool or its online warranty viewer, and a Walmart search for remotes asked for a robot check, which we did not attempt.
Prices checked November 2026: Zoro and Walmart.com (US), 19 November 2026.
Documents checked November 2026: Bruno, Harmar, Handicare, Stannah and Acorn documents, the openFDA recall data (last updated 2026-11-14) and enforcement data (no match, no update date returned) and the CPSC recall page and database, 19 November 2026.
This article is general information. Rules and prices differ by country and change, so confirm them before you buy or travel.
Common questions
Can I replace a stair lift battery myself?
The manuals we read do not give owners that job. Harmar's SL600 manual says "Contact your local dealer for proper battery replacement,"
and Bruno's warranty says repair work other than the owner's manual maintenance must be done by a Bruno dealer to keep coverage. Bruno's Elan installation manual tells technicians to switch off the carriage circuit breaker and guard against static before touching anything inside the carriage. What owners can do, by the manuals, is keep the lift parked on charge and the charger plugged in.
How long does a stairlift battery last?
Harmar's SL600 manual says "On average, replace batteries every 1-2 years based on usage."
Bruno, Handicare, Stannah and Acorn print no interval in the documents we read. Bruno's Elite manual says letting the batteries run flat "will significantly shorten the life of the batteries,"
and Harmar warns that "Annual inspection is critical to identify battery condition."
What batteries does a stairlift remote take?
Bruno's SRE-2010 Elite manual says two AA alkaline batteries, changed annually; Bruno's Elan exploded view lists the TMR-00004 transmitter "W/ 2 'AA' BATTERIES"
. Stannah's UK 600 Siena guide says three AA batteries per remote calling control, lasting "about one year with average use."
In our view, check the battery cover of your own remote.
Why does my stairlift keep beeping?
In the documents we read, beeps can mean the lift is off charge or the seat is not locked. Harmar's SL600 manual says a flashing amber light with an intermittent beep means the lift "has been stopped off the charge strip stations."
Handicare's Freecurve beeps for three minutes when it is not on a charge point. Bruno's Elan installation manual says units in multi-user mode beep once every three seconds with the seat swiveled at the top. In our view, if the beeping continues on charge, call the dealer.
Where can I buy stair lift replacement parts?
In our reading of the manuals' service lines, remotes, chargers, seats, edges and rails come through the maker's dealer. Replacement batteries and chargers are also sold by general sellers; on 19 November 2026, Zoro and Walmart.com listed them on their first results pages, with the seller naming the lift. Mobility Atlas can quote a part for you: send a part request with the stairlift maker, model, serial number and part, and you get a written quote with delivery; nothing is charged before you accept.
Is my stairlift under recall?
Check the serial number with the maker. On 19 November 2026 the FDA recall record Z-0681-2022 for Acorn 130, Brooks 130, Acorn 180 and Acorn Outdoor stairlift seats was stored as "Open, Classified". The CPSC recall 15-189 covers Acorn Superglide 120 lifts made from March 2007 to March 2011. Other stairlift recalls we found (Acorn 180 rivets, Savaria SL-1000 and Stairfriend, ThyssenKrupp LEVANT) are stored as terminated.
Sources
- Bruno: SRE-2010 Elite straight rail stairlift operator's manual, P/N 2010-O, 08 February 2019, with Bruno Gold stairlift warranty rev. 04-18 (copy on cdn.shopify.com; read 19 November 2026)
- Bruno: SRE-3000 Elan straight rail stairlift installation manual, P/N 3000-I, 08 February 2019, with exploded view REV. 11 (copy on cdn.shopify.com; read 19 November 2026)
- Bruno: Elan Straight Indoor Stairlift product page (read 19 November 2026)
- Harmar: Pinnacle SL600 stairlift owner's manual, 23JULY2024, 76016 G (read 19 November 2026)
- Harmar: SL600 Pinnacle Premium Stairlifts product page (read 19 November 2026)
- Handicare: Handicare 1100 stairlift user manual (copy on cdn.shopify.com; read 19 November 2026)
- Handicare: Freecurve stairlift user manual, 11P00388 rev.B, UK (copy on cdn.shopify.com; read 19 November 2026)
- Stannah: 600 Siena user guide "Looking after your stairlift", Issue 3, January 2013, UK (copy on cdn.shopify.com; read 19 November 2026)
- Acorn Stairlifts (US): stairlifts page (read 19 November 2026)
- Acorn Stairlifts (US): Stairlift FAQs (read 19 November 2026)
- Acorn Stairlifts (US): Stairlift Repairs and Servicing (read 19 November 2026)
- Acorn: Quick User Guide, 130 straight and 180 curved, F509.0.1 (read 19 November 2026)
- openFDA: device recalls, product code PCD, data last updated 2026-11-14 (read 19 November 2026)
- openFDA: device recalls, word search for stairlift or stair lift (read 19 November 2026)
- openFDA: device enforcement reports, product code PCD, no match (read 19 November 2026)
- CPSC: Acorn Stairlifts Recalls Motorized Stair Lifts, recall 15-189 (read 19 November 2026)
- CPSC recall database API: product name "stair lift" (read 19 November 2026)
- CPSC recall database API: product name "stairlift", no result (read 19 November 2026)
- Zoro (US): search results for "stairlift battery", first page (prices read 19 November 2026)
- Zoro (US): search results for "stairlift charger" (prices read 19 November 2026)
- Walmart.com (US): search results for "stairlift battery", page 1 (prices read 19 November 2026)
- eBay (US site): search results for "stairlift remote", first page, prices shown in Thai baht and not used (read 19 November 2026)
Read on . The wording of the article is our own.

