Wheelchair oxygen tank holder guide 2026: oxygen cylinder holders, crutch, cane and walker holders compared, how they mount, safety warnings, prices and returns
Oxygen cylinder holders, crutch, cane and walker holders for wheelchairs and scooters from Diestco, Drive, Invacare, Pride, Permobil and Vive: fit, safety, prices.
Contents
- The short answer
- How we compared, and which pages we read
- Cylinder sizes: what the pages print
- Four ways an oxygen holder mounts
- Which holder for which chair
- Fabric oxygen bags compared
- Rigid holders compared
- Oxygen holders on power chairs and scooters
- Oxygen safety: what the manuals say
- Weight, tipping and the load behind the backrest
- In a car, van or bus
- Flying with oxygen or a concentrator
- Crutch and cane holders: the types
- Cane holders for scooters, and walker holders
- What holders cost in November 2026
- Returns and warranties, as printed
- Medicare codes E2207 and E2208
- What FDA reports mention
- Ordering a holder through Mobility Atlas
- Three traps
- Three composite scenarios
- What to ask the oxygen supplier, the dealer and the therapist
- Sources and documents
- Common questions
- Sources
The short answer
A wheelchair oxygen tank holder is a bag, sleeve or metal bracket that carries a portable oxygen cylinder on a manual wheelchair, power chair or mobility scooter, so the cylinder rides with you instead of on your lap or on a separate cart. This guide compares the oxygen cylinder holder for wheelchair use that makers and US sellers list, and the wheelchair crutch holder, wheelchair cane holder and walker holder that do the same job for walking aids. For each one we give what the page prints: how it mounts, which cylinder sizes it names, what it costs, the return terms, and what the chair and scooter manuals say about weight, tipping, oxygen and vehicles. Our general wheelchair accessories guide gives these items one short section each; this page goes into the detail.
What is a wheelchair oxygen tank holder, and which kind fits my chair? Mobility Atlas read the makers' and sellers' pages for 10 priced oxygen holder listings and the chair manuals that mention oxygen, the new ones on 19 November 2026. Fabric bags hang on straps: Diestco's D and E tank holders loop around the push handles or, in scooter versions, wrap around the seatback with a hook and loop strap, and Vive's uses adjustable straps. Rigid holders, such as Drive's 150-0110 (U-bolts, its page says) and Invacare's 1496 (the rear seat frame, 1800wheelchair's page says), are brackets on the frame, or, on Pride scooters, attach to the rear hitch. The pages name D and E cylinders; Ki Mobility's Catalyst 5 manual says its holder is "designed to secure D cylinders to your wheelchair."
Ki's manual also warns that "Oxygen tanks contain a highly pressurized gas that vigorously accelerates combustion,"
and that failing to follow the supplier's instructions "can result in serious injury or death."
Three questions narrow the choice before you look at a single product. Which cylinder will you carry? Your oxygen supplier decides that, and the size letter or M number is printed on the cylinder or the delivery paperwork. Does your chair have push handles, a seatback you can strap around, or a hitch or bracket that the maker sells accessories for? And will the chair ride in a car, van or bus with you in it? In our view, the last answer matters most: Ki Mobility's Catalyst 5 manual says that if the chair has an oxygen tank holder, it must never be used as a seat in a motor vehicle, and Pride's Scooter Consumer Safety Guide says "The scooter user should never sit on the scooter while it is in a moving vehicle."
We quote both further down.
Oxygen itself is a prescription, and how much you use, which cylinder or concentrator you get and how the tubing reaches you belong to your physician and your oxygen supplier. How a load behind the backrest changes your balance, and how a crutch or cane holder fits the way you transfer, are good questions for your occupational therapist or seating clinician; a change to the chair's frame is for the dealer who services it. Mobility Atlas earns a fee or margin when you order through us; the comparison below uses only the makers' and sellers' published pages and manuals, CMS and FAA pages and openFDA records, and none of it is medical advice.
How we compared, and which pages we read
On 19 November 2026 we opened in a browser the maker and seller pages named as new in this guide and saved their text with the address and the date before writing. That covers Diestco's four oxygen tank holder pages and the mounting tag for its scooter and power chair model; Drive Medical's pages for its oxygen E cylinder holder STDS803, its D and E cylinder holder 150-0110 and its cane and crutch holder STDS1034, with their product option tabs; Vive Health's oxygen tank holder page; Pride Mobility's Jazzy oxygen tank holder and walker holder pages and its scooter oxygen tank holder, walker holder and cane holder pages; Permobil's oxygen bottle holder and crutch holder pages; and PDF pages 122 and 124 (printed pages 121 and 123) of Invacare's Tracer parts catalog 02-016, which list the oxygen holders 1496 and 1497, and PDF page 120, the recliner IV rod. We use PDF page numbers below.
For prices we read four US sellers the same day: SpinLife (its search results for oxygen and for cane holder and seven product pages), 1800wheelchair (its Cane, Crutch and Oxygen Attachments category and four product pages with their specification tabs and three of their return tabs), Vitality Medical (its search results for wheelchair oxygen holder and four product pages, plus the Skil-Care instruction sheet and Drive catalog sheet it links) and Vive Health's own store. We did not read Walmart for this guide. For codes and rules we read the October 2026 HCPCS file from CMS, Medicare's LCD L33792 version 43 and policy article A52504 version 61, and two FAA PackSafe pages, all on 19 November 2026.
Some documents were saved earlier for other guides and keep their own read dates, which we give where we use them: Merits' Atlantis order form, Permobil's M3 Corpus order form, Invacare's Tracer SX5 user manual and 1800wheelchair's Golden Compass page on 9 November 2026; Diestco's cane and crutch holder pages and its policies page, Pride's Jazzy cane and crutch holder page and SpinLife's and 1800wheelchair's return pages on 12 November 2026; and Ki Mobility's Catalyst 5 manual, Pride's Scooter Consumer Safety Guide, Pride's Baja safety guide, Hoveround's MPV5 manual, Golden's Buzzaround Extreme manual and Medicare's Benefit Policy Manual on 13 November 2026. Vive's return policy was read on 19 November 2026.
We did not buy, fit, weigh or test any holder, and we did not open any cylinder. Every size, load, price and warning below is what a page or manual prints, with the document named. Where two documents give different figures, we give both and say which one to plan on. Rules are US rules unless we name another country; prices, funding and air travel rules in the UK, the EU and elsewhere differ, so confirm locally before you buy or travel.
Cylinder sizes: what the pages print
The letters and M numbers on oxygen cylinders are size names, and the holder pages we read use them loosely, so measure your own cylinder. Vive's page is the one that prints dimensions for named sizes. Its sizing list gives a D tank as 16.5 inches tall and an E tank as 25.5 inches tall, both 4.38 inches in diameter, and smaller sizes such as M9 (10.9 inches tall, 4.38 inches across) and C (11 inches tall). Its own FAQ tells you to "measure the diameter and height of your tank."
Vive's FAQ and its sizing list do not cover the same sizes. The FAQ gives B or M6 tanks as 11.8 inches tall and 3.21 inches in diameter, but the sizing list on the same page has no M6 line at all; it has an ML6 line (7.8 inches tall, 4.38 inches across) and an M7 line. If your supplier calls your cylinder an M6, do not rely on either line: measure it, and give the seller the height and diameter in writing.
| Size as printed | Height | Diameter | Where printed |
|---|---|---|---|
| D tank | 16.5 in | 4.38 in | Vive sizing list |
| E tank | 25.5 in | 4.38 in | Vive sizing list |
| M9 | 10.9 in | 4.38 in | Vive sizing list |
| ML6 | 7.8 in | 4.38 in | Vive sizing list |
| B or M6 | 11.8 in | 3.21 in | Vive FAQ only |
| Diestco D holder | 14 in high | 6 in | Diestco B6321 page |
| Diestco E holder | 25 in high | 5 in | Diestco B6311 page |
The holder pages then name sizes without dimensions. Diestco sells a D tank holder and an E tank holder; Drive's STDS803 page says it holds an E cylinder tank; Drive's 150-0110 page says it is "Designed to hold one (1) D or E oxygen cylinder"
; Invacare's catalog lists the 1497 as "Holder, Oxygen, Black (D and E Tanks)"
; and SpinLife's page for the Pride holder says it is "designed to fit both D and E size tanks."
In our reading, a bag holder is a sleeve the cylinder stands in, not a fitted case: Diestco's D holder is 14 inches high and Vive prints a D tank as 16.5 inches tall, so by those two pages the cylinder would stand about 2.5 inches above the bag's rim. Neither page says whether that is intended, so ask Diestco or the seller before you order.
Vive's holder page lists sizes from M2 to E under "Sizing" without saying which ones the bag holds; no holder page names a smaller M size as a fit, and none names a portable oxygen concentrator. The only document we read that pairs a carrier with a concentrator is CMS's code list, where code E1354 reads "Oxygen accessory, wheeled cart for portable cylinder or portable concentrator, [...] any type, replacement only, each."
That is a cart, not a chair holder. If you use a concentrator, ask its maker how it may be carried on a chair and whether its vents must stay clear.
Four ways an oxygen holder mounts
How a holder fixes to the chair matters more than its fabric or finish, because it decides which chairs it can go on, how much it moves, and whether it gets in the way of folding or the backrest. On the pages we read, oxygen holders mount in four ways.
- Straps around the push handles. Diestco's D and E tank holders for wheelchairs say each
"Mounts with adjustable straps that loop around push handles."
Skil-Care's instruction sheet adds bottom straps to the frame. - A hook and loop strap around the seatback. Diestco's scooter and power chair holders mount
"onto seatback with a hook and loop strap,"
the B6221 page says (the B6211 page: "onto the seatback"), for chairs and scooters without push handles, as SpinLife's and 1800wheelchair's option names put it. - A rigid bracket on the frame. Drive's 150-0110 page says its bracket
"mounts to back of wheelchair with easy-to-assemble U-bolts"
; Drive's STDS803 page says a protruding bar holds the cylinder and prints no mounting method, and Vitality Medical's page says it attaches to most wheelchair frames; 1800wheelchair's page says Invacare's 1496"Attaches to the rear seat frame."
- A maker's own hitch or backrest hardware. SpinLife's page says the Pride scooter holder attaches to the universal rear hitch adapter; Permobil's page says its holder is available with different sets of mounting hardware for the Corpus 3G and PS seating systems.
In our view, strap mounts suit chairs with push handles and fit many frames, but they hang the cylinder from the top of the backrest; in our reading, that is the kind of high load Ki Mobility's general warning about objects hung "above the occupants center of gravity"
covers, although the warning does not name oxygen holders. Bracket and hitch mounts can sit lower and hold the cylinder more firmly, but each is made for a frame, a hitch or a seating system, so the fitment list on the page is the limit. Where a page prints no list, ask the seller to confirm your make and model in writing before you order. Weight and tipping get their own section below.
Which holder for which chair
The table below maps chair types to the holders whose pages name them. It is a starting list for the question you ask the seller, not a fit confirmation: where a cell names a holder, the fit is as that holder's page or manual prints it.
| Your chair | Holders whose pages name it | What to check |
|---|---|---|
| Manual chair with push handles | Diestco B6321, B6311; Skil-Care 707027 | Handle height; load on handles |
| Manual chair, Invacare Tracer | Invacare 1497, 1496 (catalog 02-016) | Your model in the catalog |
| Manual chair, Ki Catalyst 5 | Ki oxygen tank holder (manual) | D cylinders, per manual |
| Manual chair, Drive | Drive STDS803 (seller text) | Drive's page names no model |
| Jazzy power chair | Pride Jazzy holder | Most Jazzy chairs, per Pride |
| Permobil Corpus 3G or PS seat | Permobil oxygen bottle holder | Hardware set for your seat |
| Pride scooter with rear hitch | Pride ACCASMB1017 | One accessory per bracket |
| Other scooter or power chair | Diestco B6221, B6211 | Seatback height, 7 to 21 in |
Two rows rest on seller text rather than the maker's page: Vitality Medical's description of Drive's STDS803 as designed for most standard Drive wheelchairs, and SpinLife's scooter menu for Pride's ACCASMB1017. In our view, treat both as a reason to ask, and have the maker or seller confirm in writing that the holder fits your model and your cylinder before you pay. Holders that a page says fit almost anything, such as Vive's, still leave you to check that the straps sit on a part of the chair meant to carry a load; in our view, a tube that holds a backrest release or a folding hinge is not that place, and your dealer can show you which tubes are.
Fabric oxygen bags compared
Fabric holders are the cheaper family on the pages we read: the 6 bag listings in our price table ran from $17.99 to $75. Vive's prints a weight of about 11 ounces, and the Diestco and Vive bags carry a pocket. What they share is that the cylinder is held by fabric and straps, so how tight you pull the straps decides how much it swings.
| Bag, as listed | Mount, as printed | Sizes, as printed | Other printed facts |
|---|---|---|---|
| Diestco D Tank Holder B6321 | Straps around push handles | D (14 in x 6 in) | Tool pocket, reflective tape |
| Diestco E Tank Holder B6311 | Straps around push handles | E (25 in x 5 in) | Tool and ID pockets |
| Diestco D holder B6221 | Seatback hook and loop strap | D (14 in x 6 in) | Seatbacks 6 to 24 in |
| Diestco E holder B6211 | Seatback hook and loop strap | E (25 in x 5 in) | Page 6 to 24 in; tag 7 to 24 in |
| Vive LVA2060 | Adjustable straps | D and E; shortens | 11.04 oz; 28.35 x 7.68 in |
| Skil-Care 707027 | Push handles and frame | D and E | Wheelchairs 16 to 24 in |
| NYOrtho 9546 | Adjustable straps | Not named (E tank variant) | 27-1/4 x 7-1/2 in; nylon |
Diestco's two documents for the scooter and power chair holder B6211 disagree. The product page says it fits seatbacks from 6 to 24 inches high. The mounting tag linked from the same page says it fits seatbacks 7 to 24 inches tall. 1800wheelchair's page for the D version B6221 says the holder fits seatbacks from 7 to 21 inches. Plan on the narrowest figure, 7 to 21 inches, until Diestco confirms your seatback height in writing. The tag's mounting steps are short: pass the 2 inch strap between the seat and the seatback, back through the metal loop, and "Pull strap down tightly," the tag says, and it notes that "Excess strap can be cut once you have your Oxygen Tank Holder mounted."
In our view, do not cut the strap until you have tried the holder with the cylinder in it. For the wheelchair E holder B6311, 1800wheelchair's specification tab prints a depth of 26 inches against Diestco's 25; plan on 26 inches for clearance.
Vive's page claims its holder "is easy to attach to any wheelchair, transport chair, rollator or other mobility aid,"
that it is "Sized to accommodate most oxygen tank sizes including D and E cylinders,"
and that a fastener shortens it for smaller tanks. Its FAQ says the bag "is designed to carry a single cylinder"
and weighs "approximately 11.04 ounces."
Skil-Care's instruction sheet, linked from Vitality Medical's page, says its holder is designed to secure all D and E size oxygen cylinders to a standard wheelchair, and lists it for wheelchairs 16 to 24 inches. For the E cylinder it says to open the holder to full length and to "Tighten all straps to limit movement of cylinder."
NYOrtho's page, also on Vitality Medical, describes its holder as "an economical alternative to heavy steel tank holders"
that "is easily placed off-center on the back of the wheelchair to help avoid discomfort to the head."
Those are maker claims as the seller prints them; we did not test any of them.
SpinLife lists a Diestco "Oxygen Tank Bag" with four type options: D or E, each for scooters and power chairs without push handles or for chairs with push handles. SpinLife's description says it "Securely carries an oxygen tank on most mobility scooters and power wheelchairs"
and tells you to "verify compatibility with your specific mobility device and oxygen tank size."
In our reading, those four options match Diestco's own four holders.
Two details on these pages are easy to miss. Vive's FAQ explains how its bag is shortened for a smaller cylinder: "Fold the bag upward, securing the bottom fastener to the matching strap, ensuring the holder bag straps remain loose."
Vive's page gives the bag as 28.35 by 7.68 inches, which in our reading is longer than the E tank Vive itself lists at 25.5 inches, so a D cylinder needs the fold. Diestco's four pages each mention 300-yard reflective tape, which is Diestco's description of its own tape; neither Diestco nor Vive prints a load rating for its bag. In our view, ask the seller for the bag's rated load, and if none is printed, plan as if the bag holds the cylinder in place but does not make the chair any more able to carry it.
Rigid holders compared
Rigid holders reach higher prices on the pages we read: the 4 listings in our price table ran from $48.75 to $168. The pages that name a material say steel or chrome; they bolt, clamp or hitch to the frame, and one carries an IV rod too.
| Holder, as listed | Mount, as printed | Sizes, as printed | Other printed facts |
|---|---|---|---|
| Drive STDS803 | Not printed (seller: frame) | E | HCPCS E2208 on Drive's tab |
| Drive 150-0110 | U-bolts, back of chair | One D or E | Steel; also a wall mount |
| Invacare 1497 | Not printed; parts list has a clamping knob | D and E | Tracer catalog 02-016 |
| Invacare 1496 | Rear seat frame | Oxygen and IV bag | IV rod in the kit |
| Pride ACCASMB1017 | Rear hitch adapter | D and E | Most Pride scooters |
| Permobil holder | Corpus 3G or PS hardware | Standard cylinder | On the backrest |
Drive's page for the STDS803 says it holds an E cylinder tank, that a "Protruding Bar holds Oxygen Cylinder in place,"
and that a "Universal spacing sleeve can be added or removed to accommodate a secure fit with additional models."
Drive's page lists no chair models. Vitality Medical's page for the same item prints a weight of 3 pounds and says it is "Designed To Fit Most Standard Drive Medical Wheelchairs"
; that is the seller's text, not Drive's. Drive's other holder, 150-0110, is sold "4/case" on Drive's page, and Vitality Medical lists it under the Carex name at $48.75 marked "Each," although the description on the same page ends "Quantity: 4/case"; ask Vitality in writing whether the price is for one holder or four.
Invacare's Tracer parts catalog 02-016 lists two holders. The 1497 is "Holder, Oxygen, Black (D and E Tanks)"
with a clamping knob, guide tube inserts, a spacer and an instruction sheet, part 1027930. The 1496 is "Holder, I.V./Oxygen, Chrome"
with an IV rod, a base and its own instruction sheet, part 1027931. The catalog marks the hex head screw 11239X000-NLA in both holders' lists, and the 1496's chrome spacer 1017843-NLA, marked NLA, which the catalog's usage guide (PDF page 2, read 12 November 2026) lists as "No Longer Available"; ask the seller what replaces that screw. We did not read either instruction sheet. 1800wheelchair sells the 1496 under Invacare's sku 1496 and says it "Attaches to the rear seat frame and holds both the oxygen tank and I.V. bag."
The catalog covers the Tracer EX2, EXI, SX5 and SX5 Recliner; it does not say the holders fit other chairs.
Two maker pages print almost no detail. Pride's Jazzy page says its oxygen tank holder is "Compatible with most Jazzy® power wheelchairs"
and "simple to attach and easy to remove,"
and Pride's scooter page says the same for "most Pride scooters." Permobil's page says its holder is "Available with different sets of mounting hardware for the Corpus 3G and PS seating systems"
and "can accommodate a standard oxygen cylinder on the backrest"
; it does not say which cylinder is standard. Ask the dealer for the part number for your seating system and the cylinder sizes it takes.
Oxygen holders on power chairs and scooters
Many power chairs and scooters have no push handles, so the holder has to go on the seatback, a hitch or a bracket. The documents we read show three routes. First, a fabric bag strapped around the seatback, such as Diestco's B6211 and B6221. Second, the maker's own holder: Pride's scooter holder on the rear hitch, Pride's Jazzy holder, Permobil's backrest holder, or the holders that power chair order forms list. Third, for chairs carrying a ventilator, a holder on the ventilator tray.
SpinLife's page for Pride's scooter holder ACCASMB1017 is the most specific. It says the holder "attaches to the universal rear hitch adapter"
and "is compatible on almost every Pride scooter, including the Victory, Maxima, Revo, Go-Go, and Celebrity Series's, as well as the Travel Pro."
Its scooter menu lists 8 choices: Celebrity, Go-Go Elite Traveller, Legend, Maxima, Rally, Revo, Victory, Pursuit 2. SpinLife's page for Pride's walker holder adds a limit that matters here: "The bracket located on the back of all Pride scooters accommodates only one accessory at a time."
In our reading, that means a Pride scooter rider cannot carry the oxygen holder and the walker holder on the rear bracket together; ask the dealer what Pride offers if you need both.
Power chair order forms print the maker's own options with list prices. Merits' Atlantis order form, read 9 November 2026, lists an "Oxygen Tank Holder- attaches to seat bracket"
at $140 and an "Oxygen Tank Bag Holder- attaches to backrest"
under part number B6211, which is the number Diestco prints for its E tank holder for scooters, at $90, both with the code E2208. Permobil's M3 Corpus order form, read the same day, lists an "O2 Holder for Laptop Ventilator Tray"
at $373, marked as a custom option that mounts to the left or right side of the compact laptop ventilator tray. 1800wheelchair's page for the Golden Compass heavy duty power chair, read 9 November 2026, offers an oxygen tank holder as an add-on at $175. Golden's Buzzaround Extreme owner's manual, read 13 November 2026, lists an oxygen tank holder among the scooter's accessories and says to contact your Golden provider to order.
Ordering the holder with the chair has one advantage on paper: the maker or dealer chooses hardware made for that frame. Adding one later works too, but the fitment question then falls on you and the seller. In our view, when the chair is new, ask the dealer to quote the maker's holder as part of the order.
Oxygen safety: what the manuals say
A holder carries the cylinder; it does not make oxygen safe. The chair and scooter manuals we read put the oxygen warnings in their safety sections, and we quote them with their conditions and consequences. None of them replaces the instructions from your oxygen supplier, which the Ki manual says you must follow.
Ki Mobility's Catalyst 5 manual, read 13 November 2026, has a section headed Oxygen Tank Holder. It warns: "Oxygen tanks can be dangerous if not used properly. Oxygen tanks contain a highly pressurized gas that vigorously accelerates combustion. Ensure you have been provided proper instructions for using an oxygen tank by the supplier of your tank. You must heed all warnings and follow all of the instructions for use that have been provided by the supplier of your oxygen tank. Failure to follow all of the instructions for use, and heed all warnings, for oxygen tanks can result in serious injury or death."
Its use instruction says to "Ensure that the bottle is well seated in the bottom of the holder and the clamp is tightened to the point that the cylinder cannot be pulled out."
The same manual's general warnings say the chair "meets ISO 7176-16 for flammability"
and that "Resistance to ignition can change with use, aging or cleaning. Precautions should be taken to avoid ignition sources and proximity to flammable materials that can increase ignition such as oxygen and alcohol."
It goes on: "Changes to flammability may result in serious injury or death."
Pride's Scooter Consumer Safety Guide, read 13 November 2026, prints two oxygen lines as warnings. Among its warnings on reaching, bending and loose objects it says: "Ensure that all oxygen or air tubing is correctly routed and secured so that the tubing does not become entangled, kinked, or severed."
Under Flammability Precautions it says: "Exercise extreme caution when using oxygen in close proximity to electrical circuits and combustible materials. Contact your oxygen provider for information on using oxygen safely."
The same guide warns: "Do not operate your scooter while smoking,"
and that smoking while operating it "can ignite a fire that can result in serious personal injury or death."
Hoveround's MPV5 manual, read 13 November 2026, has two lines about the battery charger: "DO NOT plug in battery charger within 10 feet of an oxygen concentrator or oxygen cylinders"
and "DO NOT plug the battery charger and oxygen concentrator into the same electrical outlet."
That is one maker's manual for one chair; in our view it is worth asking your own chair's maker the same question, and our power wheelchair charger guide covers chargers in general.
Weight, tipping and the load behind the backrest
A cylinder on the push handles is a load hung high and behind you. No holder page we saved prints the weight of a filled cylinder, so ask your oxygen supplier what your full cylinder weighs, and add the holder. Two holder pages print their own weight: Vive's FAQ says its bag weighs approximately 11.04 ounces, and Vitality Medical's page for Drive's STDS803 prints 3 pounds. SpinLife's page data for Pride's scooter holder carries a product weight of 5 and a weight capacity of 10 with no unit printed; treat those as unconfirmed until Pride or SpinLife gives the unit in writing.
Ki Mobility's Catalyst 5 manual, in its general warnings, says: "Do not hang backpacks, bags or heavy objects above the occupants center of gravity. The additional weight alters the chair’s center of gravity increasing your risk of tipping over. A tip-over could result in serious injury or death."
It goes on: "If additional loads need to be carried, it is recommended to use under seat carriers and pouches."
The manual does not name oxygen holders in that warning; it is a general line about loads. Ki prints its own oxygen tank holder in a separate section, and that section names no weight limit.
Pride's Scooter Consumer Safety Guide warns: "The addition of accessories to the scooter may change the overall weight, size, and/or center of gravity of your scooter. It is important to take note of these changes to avoid damage to the scooter and surrounding property."
Pride's Baja safety guide, INFMANU4828 Rev H, is marked mandatory where it says: "To avoid bodily injury and/or property damage, you must confirm your scooter’s final transport weight with your Provider/Dealer or lift installer prior to transit,"
and that the quoted unit weight "does NOT include dealer-installed accessories (e.g., positioning components, cushions, back, portable oxygen tanks, etc.) or items being transported by the scooter (i.e. walkers, canes, etc.) and should NOT be relied upon to assess the compatibility of your finished scooter with a vehicle lift or other vehicular transport mechanisms."
That guide covers Baja scooters; in our reading the point carries to any chair that goes onto a lift: the cylinder, the walker and the cane count.
In our view, three habits reduce the load problem. Choose the lowest mount your chair's maker offers, such as a frame or hitch holder, over a bag on the push handles. Count the full cylinder, the holder and anything else on the back against the chair's weight limit. And if you push yourself in a light manual chair, ask the dealer about anti-tippers before you add the cylinder; our anti-tipper guide covers how they are set. Whether the load suits your balance is a question for your therapist.
In a car, van or bus
This is where the manuals are strictest. Ki Mobility's Catalyst 5 manual, in its section on transit use, warns: "Remove and secure any items temporarily attached to the chair while in a motor vehicle. Leaving items attached to the vent tray, battery tray or oxygen tank holder and not securing them properly and separately in a motor vehicle could result in these items becoming dangerous projectiles in the event of an accident. Additionally, oxygen tanks contain a highly pressurized gas that vigorously accelerates combustion. These factors could lead to serious injury or death to the user and/or anyone else in the vehicle."
Two lines follow in the same section. "When using this wheelchair as a seat in a motor vehicle, you must remove any items attached to the vent tray, battery tray or oxygen tank holder and properly secure them separately."
And: "If the chair is equipped with an oxygen tank holder never use the wheelchair as a seat in a motor vehicle."
The manual's list of accessories to take off for transit names "oxygen tank holders, oxygen tanks, IV poles"
and says that "In the event of an accident, these items can become dangerous projectiles which may injure or kill you or other occupants of the motor vehicle."
Those lines are printed for Ki's Catalyst 5. Pride's Scooter Consumer Safety Guide, read 13 November 2026, goes further for its scooters: "The scooter user should never sit on the scooter while it is in a moving vehicle,"
and it says the scooter should be stowed with removable parts "removed and/or properly secured during motor vehicle transport."
Invacare's Tracer SX5 manual, read 9 November 2026, goes further still in a warning: "Wheelchair users should NOT be transported in vehicles of any kind while in wheelchairs."
It says Invacare's position is that users "should be transferred into appropriate seating in vehicles for transportation."
Other manuals we read for this guide did not print a line on this; that does not mean their makers allow it. If you ride in a vehicle seated in a wheelchair or power chair, ask your chair's maker in writing whether it may be used as a seat with an oxygen holder fitted, and ask your oxygen supplier how to secure the cylinder in the vehicle. Our wheelchair van guide covers vehicles and tie-downs in general.
Flying with oxygen or a concentrator
A cylinder holder on your chair does not mean the cylinder can fly with you. The FAA's PackSafe page on oxygen, read 19 November 2026 (last updated 13 April 2026, the page says), states that "Passengers may not carry their own oxygen (compressed oxygen or liquid oxygen) in checked baggage, carry-on baggage or on their person."
It adds that compressed oxygen used in the cabin "must be provided by the airline"
and that "Airlines are not required to provide oxygen service and many do not."
It also notes that "oxygen cylinders are not allowed in baggage in the U.S."
Portable oxygen concentrators are treated differently. The same page says "Passengers may carry portable oxygen concentrators (POCs),"
and the FAA's PackSafe page on POCs says that those depending on one "must bring sufficient spare batteries in carry-on baggage for the duration of the flight"
and that "Spare batteries must be protected from damage and short circuit."
Rules outside the US differ, and each airline has its own process, so ask the airline before you book. Flying with the chair itself is covered in our guide to flying with a power chair.
Crutch and cane holders: the types
Some users who walk short distances need a crutch or cane within reach at the end of a ride, for a transfer or the first steps. Permobil's crutch holder page puts it this way: "Typically, a user will use crutches to assist with transfers, but relies on the power wheelchair for functional mobility."
The holders on the pages we read come in four types: fabric sleeves that strap to push handles or a seatback, a cup at the bottom with a strap at the top, clips that screw to an armrest, and tubes or brackets that fit a scooter's rear hitch.
Which wheelchair crutch holder or wheelchair cane holder should I choose? Mobility Atlas read the maker and seller pages for these holders and found that the mount decides. On a manual chair with push handles, Diestco's fabric holders loop around the handles; Diestco's crutch holder carries forearm and underarm crutches. Ki Mobility's Catalyst 5 manual describes a holder with a "bottom receiving cup" and a hook and loop fastener on the back cane. On Pride scooters, SpinLife's pages say the single and double cane holders attach to the rear universal accessory hitch, and Pride's cane clips screw into the armrest, two per cane. On power chairs, Pride's Jazzy cane and crutch holder ships with hardware, and Permobil sells its own. Prices on the pages we read ran from $10 for one Pride cane clip to $120 for Pride's double cane holder on SpinLife's search page. Ki's manual warns that a fall or tip-over from unsecured canes or crutches "may result in [...] serious injury or death."
Ki's instructions are the clearest we read. Its Catalyst 5 manual says: "Place narrow end of cane or crutch in the bottom receiving cup,"
then use the hook and loop fastener "to secure the cane or crutch to the upper back cane. Confirm the canes or crutches will stay securely in place, both vertically and horizontally, when the wheelchair is in motion."
Its warning in the same section first says to "Always remove any items temporarily attached to the wheelchair while in a motor vehicle,"
because they could become "dangerous projectiles," and goes on: "Additionally, secure canes or crutches in a proper manner while riding your wheelchair. These items may become entangled in the wheelchair resulting in a fall or tip-over. A fall or tip-over may result in damage to your chair or in serious injury or death."
Invacare's Tracer SX5 manual shows a fixed carrier with a clamp and base on the step tube and a strap at the back upholstery screw, and Diestco's fabric holders are described in detail in our wheelchair bag guide, so we give them one line each here. The SX5 manual's warning says to "Check base weekly to ensure proper placement"
and "NEVER insert or remove items while wheelchair is moving."
Diestco's crutch holder page lists it at 8 by 25 inches, while 1800wheelchair's specification tab for its Diestco crutch holder (sku B6-13, sold for wheelchairs or scooters) prints a depth of 26 inches and a diameter of 5 inches, against Diestco's 8 by 25 by 5 inches; plan on the longer figure when you check door clearance.
Drive's page for its Wheelchair Cane/Crutch Holder STDS1034 prints the name, the item number and a UPC and nothing about mounting or fit, and its product option tab adds nothing more. Pride's Jazzy page says its cane and crutch holder "is durable and easy to mount onto your power chair. All hardware is included."
Permobil's page says its holder lets a user "carry crutches or similar assistive device with their wheelchair."
For each of these, ask the seller for the instruction sheet and the list of chairs it fits before you order. Choosing the crutch or cane itself is covered in our guides to crutches and walking canes.
Cane holders for scooters, and walker holders
Scooter makers sell cane holders that use the scooter's own hardware. SpinLife's page for Pride's single cane holder ACCINDV1058 says it is "compatible with all Pride mobility scooters that feature the universal rear accessory attachment hitch,"
and the double cane holder ACCINDV1019 page says the same. The double holder's tile on SpinLife's search page showed $120, while its product page data carried $119.81; plan on the higher figure. SpinLife's page for Pride's cane clip ACCINDV1074 says the clips "are easily installed by screwing into the armrest of your Pride scooter"
and that "Two clips are required to hold a cane,"
at $10 each, so $20 for one cane. For Golden scooters, SpinLife's page says Golden's tube cane holder MBA-CANEHT "Fits on the mounting bracket on the back of your scooter"
and "Can be used on the Companions, Buzzaround, Buzzaround Lite and Avenger"
; its description also says it fits "all Golden scooters." Plan on the four named lines until Golden confirms your model.
Walker holders carry the largest item. Pride's Jazzy page says its walker holder "can hold either a standard or rolling walker, with a weight capacity of up to 15 pounds,"
and that it is "compatible with most Jazzy Power Chairs, including the Jazzy Select® 6 lightweight wheelchair."
Pride's scooter page gives the same 15 pound capacity and says that "you’ll also need to buy the universal accessory bar and attach it to the back of your Pride scooter."
SpinLife's page for the scooter version lists eight compatible series by model code, from the Revo 2.0 (S66/S67) to the Go-Go LX (S50LX/S54LX), and says the clevis pin that holds the accessory "is included with the original purchase of your mobility unit."
In our view, weigh your walker before you order; neither page lists walkers by name.
| Holder, as listed | Mount, as printed | Printed limit or fit | Source page |
|---|---|---|---|
| Pride walker holder, Jazzy | Not printed | 15 lb; most Jazzy chairs | Pride Jazzy page |
| Pride walker holder, scooter | Universal accessory bar | 15 lb; most Pride scooters | Pride scooter page |
| Pride single cane holder | Rear accessory hitch | Scooters with the hitch | SpinLife page |
| Pride double cane holder | Rear accessory hitch | Scooters with the hitch | SpinLife page |
| Pride cane clip, each | Screws into armrest | Two per cane | SpinLife page |
| Golden tube cane holder | Rear mounting bracket | Four Golden scooter lines | SpinLife page |
| Diestco walker holder | Not opened | For scooters (title) | 1800wheelchair tile |
SpinLife's page also says that "The bracket located on the back of all Pride scooters accommodates only one accessory at a time."
In our reading, if both holders use that rear bracket, it cannot take a walker holder and an oxygen holder together; in our view, ask the dealer whether a seatback bag such as Diestco's B6211 can carry one of them.
What holders cost in November 2026
How much does an oxygen cylinder holder for a wheelchair cost? Mobility Atlas read four US sellers on 19 November 2026 and listed 10 oxygen holder prices: the price of each oxygen holder on the product pages we opened at SpinLife, Vitality Medical and Vive Health (on Vitality's Carex page, only the 150-0110 holder, not its racks), and the three oxygen holder tiles on 1800wheelchair's attachments category. The range in our table was $17.99, for Vive's fabric holder on Vive's own store, to $168, for Invacare's chrome IV and oxygen holder 1496 at 1800wheelchair. Fabric bags ran from $17.99 to $75; rigid holders from $48.75 to $168. We left out 1800wheelchair's Drive oxygen cylinder rack and Vitality Medical search tiles whose product pages we did not open. Maker list prices on power chair order forms are a separate set: Merits' order form lists its own seat-bracket oxygen holder at $140. Prices differ by seller, date, tax and funding, so confirm before you order.
| Oxygen holder, as listed | Seller (US) | Price as printed | Note |
|---|---|---|---|
| Vive Oxygen Tank Holder LVA2060 | Vive Health | Current price $17.99 | Fabric |
| Skil-Care 707027 | Vitality Medical | $38.06 (list $42.29) | Fabric |
| Carex 150-0110, D or E holder | Vitality Medical | Price: $48.75 | Each; page also says 4/case |
| Drive STDS803 | Vitality Medical | $57.24, out of stock | Steel |
| Diestco Oxygen Tank Bag | SpinLife | $64 (struck $69) | Fabric; four types |
| Diestco 02 D-Tank Holder | 1800wheelchair | $70 | Fabric |
| NYOrtho 9546 | Vitality Medical | $74.21 (list $82.46) | Fabric |
| Diestco O2 E-Tank holder | 1800wheelchair | $75 | Fabric |
| Pride ACCASMB1017 | SpinLife | $126 (struck $198) | Rigid; scooter hitch |
| Invacare IV and Oxygen Holder 1496 | 1800wheelchair | $168 | Chrome; IV rod |
For crutch, cane and walker holders we listed 11 prices: the cane holder tiles on SpinLife's search results, minus three that are not wheelchair or scooter holders (Drive's Nitro Sprint cane holder, listed under walking aid accessories, a catheterization pants holder and a travel case), SpinLife's page for Pride's walker holder, and the three crutch, cane and walker tiles on 1800wheelchair's category. The range in our table was $10, for one Pride cane clip (two are needed per cane), to $120, for Pride's double cane holder. SpinLife's Pride walker holder was $99 with $150 struck through, plus $35 for the version for Pride power chairs with the Deluxe Contour seat.
| Holder, as listed | Seller (US) | Price as printed | Note |
|---|---|---|---|
| Cane Holder for Whill Model C2 | SpinLife | $30 | Search tile |
| Cane Holder Kit (F/Fi) | SpinLife | $89 | Search tile |
| Single Cane Holder, 3 in diameter for Pride Scooters | SpinLife | $98 | Rear hitch |
| Double Cane Holder, 3 in diameter for Pride Scooters | SpinLife | $120 | Page data $119.81 |
| Tube Cane Holder | SpinLife | $63 | Golden scooters |
| Cane Holder- Whill Model Ri | SpinLife | $50 | Search tile |
| Cane Clip Attachment, Each | SpinLife | $10 | Each; two per cane |
| Walker Holder for Pride | SpinLife | $99 | Struck $150 |
| Diestco Walker Holder for Scooters | 1800wheelchair | $68 | Tile; page not opened |
| Crutch Holder for Wheelchairs and Scooters | 1800wheelchair | $52 | Diestco B6-13 |
| Triumph Mobility Prestige Cane holder | 1800wheelchair | $28 | Tile; page not opened |
Two chair-side sources price the same kinds of holders as options. 1800wheelchair's Golden Compass page, read 9 November 2026, priced the add-ons at $175 for an oxygen tank holder, $175 for a walker holder, $96 for a cane holder, $106 for a crutch holder and $96 for a quad cane holder. Merits' Atlantis order form lists MSRPs of $98 for a cane and crutch holder on the seat bracket, $66 for a backrest crutch holder numbered B6213 (the number on Diestco's crutch holder tag) and $60 for a backrest cane holder numbered B6212; the form names no brand for either. Shipping lines and stock notes on the tiles changed from page to page, so ask for a total with delivery.
Returns and warranties, as printed
Return terms differ more than prices do, and in our view a holder that does not fit your chair is a likely return. Each term below belongs to the document that prints it.
- Diestco's policies page, read 12 November 2026, allows a return if Diestco receives the product
"within 10 days following the date of delivery,"
unused and in its original packaging, with a Return Authorization Number; it says"No restocking fee will be charged"
and that the warranty"is valid for the duration of 6 months after purchase of the product."
In our reading, that applies to products bought from Diestco. - SpinLife's pages for the Pride oxygen holder, the Diestco oxygen bag, the Pride cane holders, the cane clip, the walker holder and the Golden tube cane holder each say
"This item has a 20% Restocking Fee"
and that an RA"must be requested within 30 days of delivery."
They also say items custom-made by the manufacturer are non-returnable. - 1800wheelchair's return tab, on the three holder pages whose return tab we saved (the Diestco E tank holder, the Invacare 1496 and the crutch holder), says it offers
"a 30-day refund with a 10% to 30% restocking fee for most items"
and lists"Wheelchair accessories (bags, ramps & attachments)"
among the items with that fee; Invacare products get 45 days, and "All Parts" are listed as non-returnable. - Vive Health's return policy, read 19 November 2026, says
"All purchases have a 30-day return window"
and that customers"may be required to pay cost of return label + restocking fee,"
and applies when the"Purchase [was] made directly with Vive Health."
Its footnote applies the restocking fee to"items equal to or greater than 20lbs,"
and it says an issue"must be confirmed with a Vive Health product expert using photos or videos for a refund request to be considered."
The holder's product page lists a "60 day guarantee" under What’s Included; the two documents differ, so plan on 30 days and ask Vive in writing. - Vitality Medical's page for Drive's STDS803 prints a "30-day return policy" and "Items must be unopened."
Two warranty fields need care. SpinLife's page data for the Pride oxygen holder, the Pride double cane holder and the Pride walker holder carries a warranty line that reads "There is no warranty on these slippers, they are a single patient use item."
In our reading that line was written for another product and copied into these pages, so ask SpinLife in writing what warranty applies before you order. SpinLife's page for the Diestco bag repeats Diestco's 6 month warranty. 1800wheelchair's "All Parts" line matters if the seller treats a holder as a part: ask before you order whether your holder is returnable.
Medicare codes E2207 and E2208
Two Medicare codes name these holders. CMS's October 2026 HCPCS file, read 19 November 2026, gives E2207 as "Wheelchair accessory, crutch and cane holder, each"
and E2208 as "Wheelchair accessory, cylinder tank carrier, each."
A code is a name for billing; it does not say Medicare will pay. Drive's page and catalog sheet for the STDS803 print E2208, and Merits' Atlantis order form prints E2208 next to two oxygen holders and E2207 next to two cane or crutch holders. That is the maker's coding, not a coverage decision.
We searched the text of Medicare's LCD L33792, Wheelchair Options/Accessories, version 43 (in effect 10/01/2025 to 12/19/2026, the page says), and its policy article A52504, version 61 (same dates), by a word search for E2207, E2208, cylinder, crutch, cane holder and oxygen, on 19 November 2026. Neither page's text, as we saved it, named either code or any of those words. The code tables of the article load separately and we did not read them, so we cannot say how the article codes these items. One of the LCD's three general conditions is that an item must "be reasonable and necessary for the diagnosis or treatment of illness or injury or to improve the functioning of a malformed body member."
Both pages list a future version effective 12/20/2026, which we did not read.
Medicare's Benefit Policy Manual, chapter 15, read 13 November 2026, says that "Equipment which basically serves comfort or convenience functions or is primarily for the convenience of a person caring for the patient [...] do not constitute medical equipment."
In our reading, whether a cylinder carrier is paid depends on the supplier's claim and the DME MAC's decision, and the documents we read do not settle it either way. Ask the supplier, before delivery, whether they will bill Medicare for the holder and what you will owe if it is denied. If the oxygen comes from an oxygen supplier and the chair from a different supplier, ask both who would provide the holder. We did not read Medicare Advantage, Medicaid or VA rules for these items; ask the plan in writing. Medicare's wheelchair rules in general are covered in our wheelchair accessories guide.
What FDA reports mention
We searched openFDA's device adverse event file on 19 November 2026 (data last updated 11 November 2026) by a word search of the report narratives, limited to six device product codes (IOR, ITI, INI, IMK, KNO, ILK). A search for oxygen tank, oxygen cylinder, oxygen holder, tank holder or cylinder holder returned 4 reports; a search for crutch holder, cane holder or walker holder returned 3. The 7 reports were received between 19 March 2001 and 20 May 2019. We read each one. These are reports, not rates: FDA's page about its MAUDE database, read 9 November 2026, calls it a "passive surveillance system"
with "under-reporting of events, inaccuracies in reports, lack of verification that the device caused the reported event."
Two of the oxygen reports describe the holder or tank on the back of the chair, and a third a holder linked to pressure sores. A 2014 report on a Jumao manual chair stated that a facility "PUT AN OXYGEN HOLDER ON THE BACK OF THE VERANDA CHAIR, AND THE WEIGHT OF THE PRODUCT TORE THE UPHOLSTERY."
A 2016 Invacare report stated that "THE BACK ASSEMBLY AND ATTACHING HARDWARE ARE BENT BACKWARDS DUE TO THE USER THAT HAS AN OXYGEN TANK HANGING OFF OF THE BACK."
A 2015 report filed by Invamex stated that a dealer reported the oxygen holder on a T4 chair was "ALLEGEDLY CAUSING USER TO HAVE PRESSURE SORES ON THEIR BACK."
Pressure care is a clinician's question; in our view, if a holder presses on your back, stop using it and tell your therapist.
The fourth is a 2019 Permobil report coded as a death. It stated that the user "HAD WENT OUTSIDE TO SMOKE A CIGARETTE WHILE USING AN OXYGEN TANK,"
and that witnesses claimed to have seen the user on the ground, on fire, with the chair also burning. The report says the photos showed "AN E SIZE OXYGEN TANK WITH REGULATOR"
and that "NO ALLEGATIONS WERE MADE OF A DEVICE MALFUNCTION OR DEVIATION HAD CONTRIBUTED TO THIS EVENT."
We give it because it is the record in this search that matches the warnings quoted above: Pride's guide says "Do not operate your scooter while smoking,"
and Ki's manual says oxygen "vigorously accelerates combustion."
The three crutch and cane reports are older and mixed: a 2001 report on a Quickie chair stated "THE REAR SIDE FRAME SNAPPED OFF AT THE CANE HOLDER"
with no injuries reported; a 2005 report from a Permobil user listed among other complaints that "THE CRUTCH HOLDER IS POSITIONED WHERE IT CANNOT BE REACHED"
; and a 2012 Invacare report mentioned a cane holder in passing. A search of openFDA's recall file for oxygen holder or carrier in the same product codes returned no matches. Seven reports cannot show how often anything happens.
Ordering a holder through Mobility Atlas
Our everyday wheelchair accessories page lists an oxygen holder (Diestco's D tank holder B6321) and crutch and cane holders. Mobility Atlas can find and quote the holders in this guide, including ones that are not listed on that page and maker parts such as Invacare's 1497 or Pride's hitch holders. The process is the same for each: you send an enquiry or a part request, we send a written quote with delivery to your country, and nothing is charged before you accept it.
To get a useful quote, send four things: the make, model and year of the chair or scooter, with a photo of the back of the chair; the cylinder size your supplier gives you, or its height and diameter; how you want it mounted (push handles, seatback, frame or hitch); and, for a crutch, cane or walker holder, what you carry and its weight.
Three traps
Trap one: buying by size letter alone. The pages we read say D and E, but one page lists M6 only in its FAQ and not in its size list, and Diestco's D holder is shorter than the D cylinder Vive describes. Measure the cylinder and send the height and diameter with your order.
Trap two: forgetting the vehicle. Ki Mobility's Catalyst 5 manual says that if the chair is equipped with an oxygen tank holder, it must never be used as a seat in a motor vehicle, and that holders and tanks left attached can become dangerous projectiles. Pride's Scooter Consumer Safety Guide says "The scooter user should never sit on the scooter while it is in a moving vehicle."
If you travel seated in a wheelchair or power chair, ask your chair's maker before you fit a holder, and plan where the cylinder rides in the vehicle.
Trap three: two accessories, one bracket. SpinLife's page says the bracket on the back of Pride scooters takes only one accessory at a time, and Diestco's seatback holders differ by page on the shortest seatback they fit (6 or 7 inches, and 7 to 21 inches on 1800wheelchair's page). Before you order a walker holder and an oxygen holder for one scooter, ask the dealer where each will go.
Three composite scenarios
These are composite scenarios, not individual customers. Each uses only the documents for the products it names.
Scenario one: a Ki Catalyst 5 user carries a D cylinder. Ki's manual says its oxygen tank holder "has been designed to secure D cylinders"
and that the bottle must be well seated with the clamp "tightened to the point that the cylinder cannot be pulled out."
The user rides to work in an adapted van seated in the chair. The same manual says that if the chair has an oxygen tank holder, never use it as a seat in a motor vehicle, so the user asks the Ki dealer in writing what to do and asks the oxygen supplier how to secure the cylinder separately in the van. In our view, that answer comes before the holder is fitted, not after.
Scenario two: a Pride Victory scooter rider uses an E cylinder and a rolling walker. SpinLife's page says Pride's oxygen tank holder fits D and E tanks, attaches to the universal rear hitch adapter, and lists Victory in its scooter menu, at $126. SpinLife's walker holder page lists the Victory Series too, at $99, but says the rear bracket "accommodates only one accessory at a time."
Pride's page gives the walker holder a 15 pound weight capacity and says a universal accessory bar must be bought separately; the rider's rolling walker has not been weighed, so that limit is still unknown. SpinLife's page data for the oxygen holder also carries a weight capacity of 10 with no unit, and the weight of the rider's full E cylinder is not printed on any page we read, so that limit is unknown too; the rider asks Pride or SpinLife for the rated load in writing before ordering. When the scooter rides in a van, Pride's safety guide says "The scooter user should never sit on the scooter while it is in a moving vehicle,"
so the rider transfers to a vehicle seat. The rider asks the Pride dealer which item can go elsewhere, and keeps the tubing routed as Pride's safety guide asks, so that it does not "become entangled, kinked, or severed."
Scenario three: a manual chair user with push handles carries an E cylinder and forearm crutches. Diestco's E tank holder B6311 is 25 inches high on Diestco's page (26 inches deep on 1800wheelchair's tab) and 5 inches across and mounts with straps around the push handles; Diestco's crutch holder for wheelchairs mounts the same way and is 8 by 25 inches. Both would hang from the same handles, and Diestco's pages print no weight limit for either. The user asks the chair's dealer whether the chair's manual allows that load on the handles, and, because Diestco's policies allow a return of an unused product if Diestco receives it within 10 days of delivery, asks Diestco before ordering whether trying a holder on the chair still counts as unused.
What to ask the oxygen supplier, the dealer and the therapist
Ask the oxygen supplier:
- Which cylinder size will I get, and what are its height, diameter and full weight?
- How should the cylinder and regulator sit in a chair holder, and how do I route the tubing?
- How do I secure the cylinder in a car or van, and where do I store spares?
- If I use a concentrator, how may it be carried on a chair, and do its vents need to stay clear?
Ask the chair dealer or maker:
- Which oxygen, crutch, cane or walker holder does the maker sell for my chair, and what is its part number?
- What does my chair's manual say about loads on the push handles or backrest, and what is the total weight limit?
- Can the chair be used as a seat in a motor vehicle with a holder fitted?
- Will the holder stop the chair from folding, or the backrest from reclining or tilting?
- Is the holder returnable if it does not fit, and what warranty applies, in writing?
Ask the therapist or seating clinician:
- Does a load behind the backrest change my balance or my need for anti-tippers?
- Where should a crutch or cane sit so I can reach it for transfers?
- Could the holder press on my back or shoulders when I lean back?
Sources and documents
Method: how we checked. We opened every page and document listed below in a browser, saved its text with the address and the read date, and wrote only from those saved texts. Prices are as printed on the date given, with the price label shown on the page; ranges and counts in this guide were computed by script over the price lines named in the text, with the exclusions named. FDA searches are word searches of report narratives and are described with their dates above. Read dates: pages new to this guide on 19 November 2026; earlier documents on 9, 12 or 13 November 2026, as given in the text.
Prices checked November 2026 (19 November 2026 for SpinLife, 1800wheelchair, Vitality Medical and Vive Health; 9 November 2026 for the Merits and Permobil order forms and 1800wheelchair's Golden Compass page).
Documents checked November 2026 (maker pages, manuals, CMS, FAA and openFDA, with the read date given for each document where it is used).
This article is general information. Rules and prices differ by country and change, so confirm them before you buy or travel.
Common questions
Will any oxygen tank holder fit my wheelchair?
No single holder fits every chair. Strap bags such as Diestco's B6311 and B6321 need push handles; Diestco's B6211 and B6221 strap around a seatback instead. Rigid holders are made for frames or hitches: Invacare's 1497 appears in its Tracer parts catalog, and SpinLife's page says Pride's ACCASMB1017 attaches to the universal rear hitch adapter of most Pride scooters. Give the seller your chair's make and model and the cylinder's height and diameter, and ask for the fit in writing.
What size oxygen cylinder fits a wheelchair holder?
The holder pages we read name D and E cylinders. Vive's page prints a D tank as 16.5 inches tall and an E tank as 25.5 inches tall, both 4.38 inches across; Diestco's D holder is 14 inches high and its E holder 25 inches high. Vive's holder page lists sizes from M2 to E under "Sizing" without saying which ones the bag holds; no holder page names a smaller M size as a fit, so measure your cylinder and ask the seller before you order.
Is it safe to carry an oxygen tank on the back of a wheelchair?
Ki Mobility's Catalyst 5 manual describes its own holder with conditions. It says the cylinder must be well seated with the clamp tightened so it cannot be pulled out, warns that oxygen "vigorously accelerates combustion,"
and says never to use the chair as a seat in a motor vehicle with an oxygen tank holder fitted; Pride's scooter guide says "The scooter user should never sit on the scooter while it is in a moving vehicle."
Ki's general warnings also say heavy objects hung above the occupant's center of gravity increase the risk of tipping. Ki's manual says to follow your oxygen supplier's instructions, and Pride's scooter guide says to route and secure the tubing and not to drive while smoking.
How much does a wheelchair oxygen tank holder cost?
On 19 November 2026 the oxygen holder prices we listed at SpinLife, 1800wheelchair, Vitality Medical and Vive Health ran from $17.99 for Vive's fabric holder to $168 for Invacare's chrome IV and oxygen holder at 1800wheelchair. Fabric bags ran from $17.99 to $75 and rigid holders from $48.75 to $168. Prices differ by seller, country, date, tax and funding, so confirm the total with delivery before you order.
Does Medicare pay for a wheelchair oxygen tank holder or crutch holder?
There are codes for both: E2208 for a cylinder tank carrier and E2207 for a crutch and cane holder, in CMS's HCPCS file. A code is not coverage. The text of LCD L33792 and article A52504 we read named neither code, and Medicare's manual says comfort or convenience equipment is not medical equipment; the documents we read do not say whether a holder falls under that line. Ask your supplier before delivery whether they will bill Medicare and what you owe if it is denied; we did not read Medicare Advantage, Medicaid or VA rules.
Can I return a holder that does not fit?
It depends on the seller. Diestco's own policy allows returns received within 10 days of delivery with no restocking fee; SpinLife's holder pages print a 20% restocking fee and a 30 day window for an RA; 1800wheelchair's tab lists a 10% to 30% fee on wheelchair accessories and says all parts are non-returnable; Vive's policy has a 30 day return window (its product page lists a 60 day guarantee). Ask before you order whether trying the holder on the chair counts as use.
Sources
- Diestco: D Tank Holder for Wheelchair B6321
- Diestco: E Tank Holder for Wheelchair B6311
- Diestco: D Tank Holder for Scooter/Powerchair B6221
- Diestco: E Tank Holder for Scooter/Powerchair B6211
- Diestco: mounting tag, Oxygen Tank Holder B6211
- Diestco: Crutch Holder for Wheelchairs (read 12 November 2026)
- Diestco: Policies, returns and 6-month warranty (read 12 November 2026)
- Drive Medical: Oxygen E Cylinder Holders STDS803
- Drive Medical: Cylinder Holder for Wheelchair, D,E Cylinders 150-0110
- Drive Medical: Wheelchair Cane/Crutch Holder STDS1034
- Vive Health: Oxygen Tank Holder LVA2060 (price read 19 November 2026)
- Vive Health: Shipping and return policy (read 19 November 2026)
- Pride Mobility: Jazzy accessories, Oxygen Tank Holder
- Pride Mobility: Jazzy accessories, Walker Holder
- Pride Mobility: Jazzy accessories, Cane Crutch Holder (read 12 November 2026)
- Pride Mobility: Scooter accessories, Oxygen Tank Holder
- Pride Mobility: Scooter accessories, Walker Holder
- Pride Mobility: Scooter accessories, Single or Double Cane Clip Attachment
- Pride Mobility: Scooter Consumer Safety Guide (read 13 November 2026)
- Pride Mobility: Baja Non-Medical Consumer Safety Guide INFMANU4828 Rev H (read 13 November 2026)
- Permobil: Oxygen Bottle Holder
- Permobil: Crutch Holder
- Permobil: M3 Corpus order form (read 9 November 2026)
- Invacare: Tracer EX2, EXI, SX5 and SX5 Recliner parts catalog 02-016, oxygen holder pages
- Invacare: Tracer parts catalog 02-016, usage guide page (read 12 November 2026)
- Invacare: Tracer SX5 user manual 1110550 (read 9 November 2026)
- Ki Mobility: Catalyst 5 user instruction manual and warranty (read 13 November 2026)
- Hoveround: MPV5 owner's manual Rev U (read 13 November 2026)
- Golden Technologies: Buzzaround Extreme owner's manual (read 13 November 2026)
- Merits Health: Atlantis P710 order form (read 9 November 2026)
- SpinLife: search results for oxygen (prices read 19 November 2026)
- SpinLife: search results for cane holder (prices read 19 November 2026)
- SpinLife: Pride Oxygen Tank Holder for Pride Scooters ACCASMB1017
- SpinLife: Diestco Oxygen Tank Bag
- SpinLife: Pride Single Cane Holder ACCINDV1058
- SpinLife: Pride Double Cane Holder ACCINDV1019
- SpinLife: Pride Cane Clip Attachment ACCINDV1074
- SpinLife: Walker Holder for Pride
- SpinLife: Golden Tube Cane Holder MBA-CANEHT
- 1800wheelchair: Cane, Crutch and Oxygen Attachments (prices read 19 November 2026)
- 1800wheelchair: Invacare IV and Oxygen Holder, with return tab
- 1800wheelchair: Diestco O2 E-Tank holder for Wheelchair, with specification tab
- 1800wheelchair: Diestco 02 D-Tank Holder
- 1800wheelchair: Crutch Holder for Wheelchairs and Scooters, with specification and return tabs
- 1800wheelchair: Golden Compass Heavy Duty Powerchair, accessory options (read 9 November 2026)
- Vitality Medical: search results for wheelchair oxygen holder (prices read 19 November 2026)
- Vitality Medical: Skil-Care Wheelchair Oxygen Cylinder Holder 707027
- Skil-Care: Oxygen Cylinder Holder 707027 instructions (hosted by Vitality Medical)
- Vitality Medical: NYOrtho Oxygen Holder for Wheelchairs
- Vitality Medical: Carex Cylinder Holder for Wheelchair
- Vitality Medical: Drive Universal Wheelchair Oxygen E Cylinder Holder STDS803
- Drive Medical: catalog sheet, Oxygen E Cylinder Holders (hosted by Vitality Medical)
- SpinLife: Return policy (read 12 November 2026)
- CMS: October 2026 Alpha-Numeric HCPCS file, codes E1354, E1355, E2207 and E2208
- CMS: LCD L33792, Wheelchair Options/Accessories, version 43
- CMS: Article A52504, Wheelchair Options/Accessories Policy Article, version 61
- CMS: Medicare Benefit Policy Manual, chapter 15 (read 13 November 2026)
- FAA: PackSafe, Oxygen (compressed or liquid)
- FAA: PackSafe, Portable Oxygen Concentrators
- FDA: About the MAUDE database (read 9 November 2026)
- openFDA: device adverse event reports, word search for oxygen tank, cylinder or holder, six device product codes
- openFDA: device adverse event reports, word search for crutch, cane or walker holder, six product codes
- openFDA: device recalls, word search for oxygen holder or carrier, six product codes
Read on . The wording of the article is our own.




